Re: [PATCH v2 3/5] pinctrl: renesas: pinctrl-rzg2l: Add support to get/set pin config for GPIO port pins

["Lad, Prabhakar" <prabhakar.csengg@xxxxxxxxx>]

Hi Geert,

Thank you for the review.

On Mon, Nov 8, 2021 at 3:36 PM Geert Uytterhoeven <geert@xxxxxxxxxxxxxx> wrote:
>
> Hi Prabhakar,
>
> On Fri, Oct 29, 2021 at 2:44 PM Lad Prabhakar
> <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx> wrote:
> > Add support to get/set pin config for GPIO port pins.
> >
> > Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@xxxxxxxxxxxxxx>
> > Reviewed-by: Biju Das <biju.das.jz@xxxxxxxxxxxxxx>
>
> Thanks for your patch!
>
> > --- a/drivers/pinctrl/renesas/pinctrl-rzg2l.c
> > +++ b/drivers/pinctrl/renesas/pinctrl-rzg2l.c
>
> > @@ -495,6 +512,14 @@ static int rzg2l_pinctrl_pinconf_get(struct pinctrl_dev *pctldev,
> >                 port = RZG2L_SINGLE_PIN_GET_PORT(*pin_data);
> >                 cfg = RZG2L_SINGLE_PIN_GET_CFGS(*pin_data);
> >                 bit = RZG2L_SINGLE_PIN_GET_BIT(*pin_data);
> > +       } else {
> > +               cfg = RZG2L_GPIO_PORT_GET_CFGS(*pin_data);
> > +               port = RZG2L_PIN_ID_TO_PORT(_pin);
> > +               bit = RZG2L_PIN_ID_TO_PIN(_pin);
> > +               port_pin = true;
>
> Instead of setting this flag, perhaps port should be adjusted?

Something like below?

#define RZG2L_PORT_START_OFFSET 0x10

port = RZG2L_PIN_ID_TO_PORT_pin) + RZG2L_PORT_START_OFFSET;
rzg2l_validate_gpio_pin(pctrl, *pin_data, port - RZG2L_PORT_START_OFFSET, bit)

and rename port -> port_offset in rzg2l_pinctrl_pinconf_get/set Or
would you prefer to change the RZG2L_PIN_ID_TO_PORT macro and adjust
the entire file?

> Then rzg2l_r{ead,mw}_pin_config() don't have to care about that
> anymore.
>
Agreed.

Cheers,
Prabhakar

> > +
> > +               if (rzg2l_validate_gpio_pin(pctrl, *pin_data, port, bit))
> > +                       return -EINVAL;
> >         }
> >
> >         switch (param) {
> > @@ -557,6 +582,14 @@ static int rzg2l_pinctrl_pinconf_set(struct pinctrl_dev *pctldev,
> >                 port = RZG2L_SINGLE_PIN_GET_PORT(*pin_data);
> >                 cfg = RZG2L_SINGLE_PIN_GET_CFGS(*pin_data);
> >                 bit = RZG2L_SINGLE_PIN_GET_BIT(*pin_data);
> > +       } else {
> > +               cfg = RZG2L_GPIO_PORT_GET_CFGS(*pin_data);
> > +               port = RZG2L_PIN_ID_TO_PORT(_pin);
> > +               bit = RZG2L_PIN_ID_TO_PIN(_pin);
> > +               port_pin = true;
>
> Likewise.
>
> > +
> > +               if (rzg2l_validate_gpio_pin(pctrl, *pin_data, port, bit))
> > +                       return -EINVAL;
> >         }
> >
> >         for (i = 0; i < num_configs; i++) {
>
> Gr{oetje,eeting}s,
>
>                         Geert
>
> --
> Geert Uytterhoeven -- There's lots of Linux beyond ia32 -- geert@xxxxxxxxxxxxxx
>
> In personal conversations with technical people, I call myself a hacker. But
> when I'm talking to journalists I just say "programmer" or something like that.
>                                 -- Linus Torvalds