[PATCH v3 00/16] Basic StarFive JH7100 RISC-V SoC support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



This series adds support for the StarFive JH7100 RISC-V SoC. The SoC has
many devices that need non-coherent dma operations to work which isn't
upstream yet[1], so this just adds basic support to boot up, get a
serial console, blink an LED and reboot itself. Unlike the Allwinner D1
this chip doesn't use any extra pagetable bits, but instead the DDR RAM
appears twice in the memory map, with and without the cache.

The JH7100 is a test chip for the upcoming JH7110 and about 300 BeagleV
Starlight Beta boards were sent out with them as part of a now cancelled
BeagleBoard.org project. However StarFive has produced more of the
JH7100s and more boards will be available[2] to buy. I've seen pictures
of the new boards now, so hopefully before the end of the year.

This series is also available at
https://github.com/esmil/linux/commits/starlight-minimal
..but a more complete kernel including drivers for non-coherent
peripherals based on this series can be found at
https://github.com/starfive-tech/linux/tree/visionfive

[1]: https://lore.kernel.org/linux-riscv/20210723214031.3251801-2-atish.patra@xxxxxxx/
[2]: https://www.linkedin.com/pulse/starfive-release-open-source-single-board-platform-q3-2021-starfive/

/Emil

Changes since v2:
- Ahmad and Geert agreed to switch the license of the clock and reset dt
  headers to GPL-2.0 OR MIT, so that both headers and device tree files
  can all use the same license.
  Bindings are still GPL-2.0-only OR BSD-2-Clause as recommended.
- Clock and reset drivers now set .suppress_bind_attrs = true and use
  builtin_platform_driver_probe to make sure the probe function is only
  called at init time so we can use __init and __initconst.
- The clock driver now uses devm_clk_hw_register and .parent_data when
  registering clocks. This way we can use the dt clock indexes rather
  than strings for parent lists and decrease the amount of static data
  needed considerably.
- Various dt binding cleanups from Rob
- Reworked description in the pinctrl dt binding.
- Pinctrl driver now depends on CONFIG_OF again since it uses
  pinconf_generic_parse_dt_config which is otherwise not defined.
- Pinctrl no longer devm_kfree's data that won't be referenced
  if dt pinconf parsing fails before registering groups and function,
  and other nits by Andy.
- The dw8250 quirk no longer needs a skip_clk_set_rate bit, but sets
  port->set_termios to the function called after clk_set_rate.

Changes since v1:
- Let SOC_STARFIVE select RESET_CONTROLLER but drop SERIAL_8250_DW
- Add missing Signed-of-by to clock dt-binding header
- Use builtin_platform_driver macro for the clock driver, add explicit
  comment to the determine_rate callback and other small nits from Andy
- Use reset-controller for node names in documentation and device tree
- Use readl_poll_timeout in reset driver to avoid hanging forever if a
  driver leaves the associated clock gated and sort Kconfig and Makefile
  entries properly.
- In the pinctrl driver align register names with documentation, remove
  invalid __init tag from probe function, use of_property_* functions to
  parse device tree, hoist pinmux unpacking into helper function to
  better document what's going on, bail on invalid signal group in
  device tree and fix many other nits from Andy.
- Refactor and rebase 8250_dw quirk on tty-next

Emil Renner Berthing (12):
  RISC-V: Add StarFive SoC Kconfig option
  dt-bindings: timer: Add StarFive JH7100 clint
  dt-bindings: interrupt-controller: Add StarFive JH7100 plic
  dt-bindings: reset: Add Starfive JH7100 reset bindings
  reset: starfive-jh7100: Add StarFive JH7100 reset driver
  dt-bindings: pinctrl: Add StarFive pinctrl definitions
  dt-bindings: pinctrl: Add StarFive JH7100 bindings
  pinctrl: starfive: Add pinctrl driver for StarFive SoCs
  dt-bindings: serial: snps-dw-apb-uart: Add JH7100 uarts
  serial: 8250_dw: Add StarFive JH7100 quirk
  RISC-V: Add initial StarFive JH7100 device tree
  RISC-V: Add BeagleV Starlight Beta device tree

Geert Uytterhoeven (4):
  dt-bindings: clock: starfive: Add JH7100 clock definitions
  dt-bindings: clock: starfive: Add JH7100 bindings
  clk: starfive: Add JH7100 clock generator driver
  dt-bindings: reset: Add StarFive JH7100 reset definitions

 .../clock/starfive,jh7100-clkgen.yaml         |   56 +
 .../sifive,plic-1.0.0.yaml                    |    1 +
 .../pinctrl/starfive,jh7100-pinctrl.yaml      |  307 ++++
 .../bindings/reset/starfive,jh7100-reset.yaml |   38 +
 .../bindings/serial/snps-dw-apb-uart.yaml     |    5 +
 .../bindings/timer/sifive,clint.yaml          |    1 +
 MAINTAINERS                                   |   22 +
 arch/riscv/Kconfig.socs                       |    8 +
 arch/riscv/boot/dts/Makefile                  |    1 +
 arch/riscv/boot/dts/starfive/Makefile         |    2 +
 .../dts/starfive/jh7100-beaglev-starlight.dts |  164 ++
 arch/riscv/boot/dts/starfive/jh7100.dtsi      |  230 +++
 drivers/clk/Kconfig                           |    1 +
 drivers/clk/Makefile                          |    1 +
 drivers/clk/starfive/Kconfig                  |    9 +
 drivers/clk/starfive/Makefile                 |    3 +
 drivers/clk/starfive/clk-starfive-jh7100.c    |  689 +++++++++
 drivers/pinctrl/Kconfig                       |   17 +
 drivers/pinctrl/Makefile                      |    1 +
 drivers/pinctrl/pinctrl-starfive.c            | 1353 +++++++++++++++++
 drivers/reset/Kconfig                         |    7 +
 drivers/reset/Makefile                        |    1 +
 drivers/reset/reset-starfive-jh7100.c         |  178 +++
 drivers/tty/serial/8250/8250_dw.c             |    3 +
 include/dt-bindings/clock/starfive-jh7100.h   |  202 +++
 .../dt-bindings/pinctrl/pinctrl-starfive.h    |  275 ++++
 include/dt-bindings/reset/starfive-jh7100.h   |  126 ++
 27 files changed, 3701 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/clock/starfive,jh7100-clkgen.yaml
 create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml
 create mode 100644 Documentation/devicetree/bindings/reset/starfive,jh7100-reset.yaml
 create mode 100644 arch/riscv/boot/dts/starfive/Makefile
 create mode 100644 arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts
 create mode 100644 arch/riscv/boot/dts/starfive/jh7100.dtsi
 create mode 100644 drivers/clk/starfive/Kconfig
 create mode 100644 drivers/clk/starfive/Makefile
 create mode 100644 drivers/clk/starfive/clk-starfive-jh7100.c
 create mode 100644 drivers/pinctrl/pinctrl-starfive.c
 create mode 100644 drivers/reset/reset-starfive-jh7100.c
 create mode 100644 include/dt-bindings/clock/starfive-jh7100.h
 create mode 100644 include/dt-bindings/pinctrl/pinctrl-starfive.h
 create mode 100644 include/dt-bindings/reset/starfive-jh7100.h

-- 
2.33.1




[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux