Re: [PATCH v2 11/16] dt-bindings: pinctrl: Add StarFive JH7100 bindings

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 

On Thu, Oct 21, 2021 at 07:42:18PM +0200, Emil Renner Berthing wrote:
> Add bindings for the StarFive JH7100 GPIO/pin controller.
> 
> Signed-off-by: Emil Renner Berthing <kernel@xxxxxxxx>
> ---
>  .../pinctrl/starfive,jh7100-pinctrl.yaml      | 274 ++++++++++++++++++
>  1 file changed, 274 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml
> new file mode 100644
> index 000000000000..342ecd91a3b0
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/starfive,jh7100-pinctrl.yaml
> @@ -0,0 +1,274 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/starfive,jh7100-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: StarFive JH7100 Pin Controller Device Tree Bindings
> +
> +maintainers:
> +  - Emil Renner Berthing <kernel@xxxxxxxx>
> +  - Drew Fustini <drew@xxxxxxxxxxxxxxx>
> +
> +properties:
> +  compatible:
> +    const: starfive,jh7100-pinctrl
> +
> +  reg:
> +    minItems: 2
> +    maxItems: 2
> +
> +  reg-names:
> +    items:
> +      - const: "gpio"
> +      - const: "padctl"

Don't need quotes.

> +
> +  clocks:
> +    maxItems: 1
> +
> +  resets:
> +    maxItems: 1
> +
> +  gpio-controller: true
> +
> +  "#gpio-cells":
> +    const: 2
> +    description: |
> +      Number of cells in GPIO specifier. Since the generic GPIO
> +      binding is used, the amount of cells must be specified as 2.
> +
> +  interrupts:
> +    maxItems: 1
> +    description: The GPIO parent interrupt.
> +
> +  interrupt-controller: true
> +
> +  "#interrupt-cells":
> +    const: 2
> +
> +  starfive,signal-group:
> +    description: |
> +      The SoC has a global setting selecting one of 7 different pinmux
> +      configurations of the pads named GPIO[0:63] and FUNC_SHARE[0:141]. After
> +      this global setting is chosen only the 64 "GPIO" pins can be further
> +      muxed by configuring them to be controlled by certain peripherals rather
> +      than software.
> +      Note that in configuration 0 none of GPIOs are routed to pads, and only
> +      in configuration 1 are the GPIOs routed to the pads named GPIO[0:63].
> +      If this property is not set it defaults to the configuration already
> +      chosen by the earlier boot stages.
> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [0, 1, 2, 3, 4, 5, 6]
> +
> +required:
> +  - compatible
> +  - reg
> +  - reg-names
> +  - clocks
> +  - gpio-controller
> +  - "#gpio-cells"
> +  - interrupts
> +  - interrupt-controller
> +  - "#interrupt-cells"
> +
> +patternProperties:
> +  '-[0-9]*$':

Can you make this more specific. As-is, '-' and 'foo-' are valid.

> +    type: object
> +    patternProperties:
> +      '-pins*$':

So foo-pinsssssss is okay? Drop the '*' or use ? if you intend to 
support 'foo-pin'.

> +        type: object
> +        description: |
> +          A pinctrl node should contain at least one subnode representing the
> +          pinctrl groups available on the machine. Each subnode will list the
> +          pins it needs, and how they should be configured, with regard to
> +          muxer configuration, bias, input enable/disable, input schmitt
> +          trigger enable/disable, slew-rate and drive strength.
> +        $ref: "/schemas/pinctrl/pincfg-node.yaml"
> +
> +        properties:
> +          pins:
> +            description: |
> +              The list of pin identifiers that properties in the node apply to.
> +              This should be set using either the PAD_GPIO or PAD_FUNC_SHARE
> +              macro. Either this or "pinmux" has to be specified.
> +
> +          pinmux:
> +            description: |
> +              The list of GPIO identifiers and their mux settings that
> +              properties in the node apply to. This should be set using the
> +              GPIOMUX macro. Either this or "pins" has to be specified.
> +
> +          bias-disable: true
> +
> +          bias-pull-up:
> +            type: boolean

Already has a type. Need to reference the common schema.

> +
> +          bias-pull-down:
> +            type: boolean
> +
> +          drive-strength:
> +            enum: [ 14, 21, 28, 35, 42, 49, 56, 63 ]
> +
> +          input-enable: true
> +
> +          input-disable: true
> +
> +          input-schmitt-enable: true
> +
> +          input-schmitt-disable: true
> +
> +          slew-rate:
> +            maximum: 7
> +
> +          starfive,strong-pull-up:
> +            description: enable strong pull-up.
> +            type: boolean
> +
> +        additionalProperties: false
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/clock/starfive-jh7100.h>
> +    #include <dt-bindings/reset/starfive-jh7100.h>
> +    #include <dt-bindings/pinctrl/pinctrl-starfive.h>
> +
> +    soc {
> +        #address-cells = <2>;
> +        #size-cells = <2>;
> +
> +        gpio: pinctrl@11910000 {
> +            compatible = "starfive,jh7100-pinctrl";
> +            reg = <0x0 0x11910000 0x0 0x10000>,
> +                  <0x0 0x11858000 0x0 0x1000>;
> +            reg-names = "gpio", "padctl";
> +            clocks = <&clkgen JH7100_CLK_GPIO_APB>;
> +            resets = <&clkgen JH7100_RSTN_GPIO_APB>;
> +            interrupts = <32>;
> +            gpio-controller;
> +            #gpio-cells = <2>;
> +            interrupt-controller;
> +            #interrupt-cells = <2>;
> +            starfive,signal-group = <6>;
> +
> +            gmac_pins_default: gmac-0 {
> +                gtxclk-pins {
> +                    pins = <PAD_FUNC_SHARE(115)>;
> +                    bias-pull-up;
> +                    drive-strength = <35>;
> +                    input-enable;
> +                    input-schmitt-enable;
> +                    slew-rate = <0>;
> +                };
> +                miitxclk-pins {
> +                    pins = <PAD_FUNC_SHARE(116)>;
> +                    bias-pull-up;
> +                    drive-strength = <14>;
> +                    input-enable;
> +                    input-schmitt-disable;
> +                    slew-rate = <0>;
> +                };
> +                tx-pins {
> +                    pins = <PAD_FUNC_SHARE(117)>,
> +                           <PAD_FUNC_SHARE(119)>,
> +                           <PAD_FUNC_SHARE(120)>,
> +                           <PAD_FUNC_SHARE(121)>,
> +                           <PAD_FUNC_SHARE(122)>,
> +                           <PAD_FUNC_SHARE(123)>,
> +                           <PAD_FUNC_SHARE(124)>,
> +                           <PAD_FUNC_SHARE(125)>,
> +                           <PAD_FUNC_SHARE(126)>;
> +                    bias-disable;
> +                    drive-strength = <35>;
> +                    input-disable;
> +                    input-schmitt-disable;
> +                    slew-rate = <0>;
> +                };
> +                rxclk-pins {
> +                    pins = <PAD_FUNC_SHARE(127)>;
> +                    bias-pull-up;
> +                    drive-strength = <14>;
> +                    input-enable;
> +                    input-schmitt-disable;
> +                    slew-rate = <6>;
> +                };
> +                rxer-pins {
> +                    pins = <PAD_FUNC_SHARE(129)>;
> +                    bias-pull-up;
> +                    drive-strength = <14>;
> +                    input-enable;
> +                    input-schmitt-disable;
> +                    slew-rate = <0>;
> +                };
> +                rx-pins {
> +                    pins = <PAD_FUNC_SHARE(128)>,
> +                           <PAD_FUNC_SHARE(130)>,
> +                           <PAD_FUNC_SHARE(131)>,
> +                           <PAD_FUNC_SHARE(132)>,
> +                           <PAD_FUNC_SHARE(133)>,
> +                           <PAD_FUNC_SHARE(134)>,
> +                           <PAD_FUNC_SHARE(135)>,
> +                           <PAD_FUNC_SHARE(136)>,
> +                           <PAD_FUNC_SHARE(137)>,
> +                           <PAD_FUNC_SHARE(138)>,
> +                           <PAD_FUNC_SHARE(139)>,
> +                           <PAD_FUNC_SHARE(140)>,
> +                           <PAD_FUNC_SHARE(141)>;
> +                    bias-pull-up;
> +                    drive-strength = <14>;
> +                    input-enable;
> +                    input-schmitt-enable;
> +                    slew-rate = <0>;
> +                };
> +            };
> +
> +            i2c0_pins_default: i2c0-0 {
> +                i2c-pins {
> +                    pinmux = <GPIOMUX(62, GPO_LOW,
> +                              GPO_I2C0_PAD_SCK_OEN,
> +                              GPI_I2C0_PAD_SCK_IN)>,
> +                             <GPIOMUX(61, GPO_LOW,
> +                              GPO_I2C0_PAD_SDA_OEN,
> +                              GPI_I2C0_PAD_SDA_IN)>;
> +                    bias-disable; /* external pull-up */
> +                    input-enable;
> +                    input-schmitt-enable;
> +                };
> +            };
> +
> +            uart3_pins_default: uart3-0 {
> +                rx-pin {
> +                    pinmux = <GPIOMUX(13, GPO_LOW, GPO_DISABLE,
> +                              GPI_UART3_PAD_SIN)>;
> +                    bias-pull-up;
> +                    input-enable;
> +                    input-schmitt-enable;
> +                };
> +                tx-pin {
> +                    pinmux = <GPIOMUX(14, GPO_UART3_PAD_SOUT,
> +                              GPO_ENABLE, GPI_NONE)>;
> +                    bias-disable;
> +                    input-disable;
> +                    input-schmitt-disable;
> +                };
> +            };
> +        };
> +
> +        gmac {
> +            pinctrl-0 = <&gmac_pins_default>;
> +            pinctrl-names = "default";
> +        };
> +
> +        i2c0 {
> +            pinctrl-0 = <&i2c0_pins_default>;
> +            pinctrl-names = "default";
> +        };
> +
> +        uart3 {
> +            pinctrl-0 = <&uart3_pins_default>;
> +            pinctrl-names = "default";
> +        };
> +    };
> +
> +...
> -- 
> 2.33.1
> 
>
[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux