Re: [PATCH v2 06/16] clk: starfive: Add JH7100 clock generator driver

[Stephen Boyd <sboyd@xxxxxxxxxx>]

Quoting Emil Renner Berthing (2021-10-26 15:35:36)
> On Tue, 26 Oct 2021 at 22:20, Stephen Boyd <sboyd@xxxxxxxxxx> wrote:
> > Quoting Emil Renner Berthing (2021-10-21 10:42:13)
> > > +};
> > > +
> > > +struct clk_starfive_jh7100_priv {
> > > +       /* protect registers against overlapping read-modify-write */
> > > +       spinlock_t rmw_lock;
> >
> > Does overlapping mean concurrent?
> 
> Yes, sorry.
> 
> > Do different clks share the same registers?
> 
> No, each clock has their own register, but they use that register both
> to gate the clock and other configuration. The Locking chapter of
> Documentation/driver-api/clk.rst talks about the prepare lock and the
> enable lock and then says:
> "However, access to resources that are shared between operations of
> the two groups needs to be protected by the drivers. An example of
> such a resource would be a register that controls both the clock rate
> and the clock enable/disable state."

Alright got it. Maybe say "protect clk enable and set rate from
happening at the same time".

> 
> > > +               return ERR_PTR(-EINVAL);
> > > +       }
> > > +
> > > +       if (idx >= JH7100_CLK_PLL0_OUT)
> > > +               return priv->pll[idx - JH7100_CLK_PLL0_OUT];
> > > +
> > > +       return &priv->reg[idx].hw;
> > > +}
> > > +
> > > +static int __init clk_starfive_jh7100_probe(struct platform_device *pdev)
> >
> > Drop __init as this can be called after kernel init is over.
> 
> Oh interesting, I'd like to know when that can happen. The comment for
> the builtin_platform_driver macro says it's just a wrapper for

I thought this was using module_platform_driver() macro?

> device_initcall.
> 
> Won't we then need to remove all the __initconst tags too since the
> probe function walks through jh7100_clk_data which eventually
> references all __initconst data?

Yes. If it's builtin_platform_driver() it can't be a module/tristate
Kconfig, in which case all the init markings can stay.

> 
> > > +
> > > +               clk->hw.init = &init;
> > > +               clk->idx = idx;
> > > +               clk->max = jh7100_clk_data[idx].max;
> > > +
> > > +               ret = clk_hw_register(priv->dev, &clk->hw);
> >
> > Why not use devm_clk_hw_register()?
> 
> I probably could. Just for my understanding that's just to avoid the
> loop on error below, because as a builtin driver the device won't
> otherwise go away, right?

Yes

> 
> > > +               if (ret)
> > > +                       goto err;
> > > +       }
> > > +
> > > +       ret = devm_of_clk_add_hw_provider(priv->dev, clk_starfive_jh7100_get, priv);
> > > +       if (ret)
> > > +               goto err;
> > > +
> > > +       return 0;
> > > +err:
> > > +       while (idx)
> > > +               clk_hw_unregister(&priv->reg[--idx].hw);
> > > +       return ret;
> > > +}
> > > +
> > > +static const struct of_device_id clk_starfive_jh7100_match[] = {
> > > +       { .compatible = "starfive,jh7100-clkgen" },
> > > +       { /* sentinel */ }
> > > +};
> >
> > Please add MODULE_DEVICE_TABLE()
> 
> Will do!

If it's never going to be a module then don't add any module_* things.