[PATCH v2 16/16] RISC-V: Add BeagleV Starlight Beta device tree

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add initial device tree for the BeagleV Starlight Beta board. About 300
of these boards were sent out as part of a now cancelled BeagleBoard.org
project.

I2C timing data is based on the device tree in the vendor u-boot port.
Heartbeat LED added by Geert.

Signed-off-by: Emil Renner Berthing <kernel@xxxxxxxx>
Co-developed-by: Geert Uytterhoeven <geert@xxxxxxxxxxxxxx>
Signed-off-by: Geert Uytterhoeven <geert@xxxxxxxxxxxxxx>
---
 arch/riscv/boot/dts/Makefile                  |   1 +
 arch/riscv/boot/dts/starfive/Makefile         |   2 +
 .../dts/starfive/jh7100-beaglev-starlight.dts | 162 ++++++++++++++++++
 3 files changed, 165 insertions(+)
 create mode 100644 arch/riscv/boot/dts/starfive/Makefile
 create mode 100644 arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts

diff --git a/arch/riscv/boot/dts/Makefile b/arch/riscv/boot/dts/Makefile
index fe996b88319e..ff174996cdfd 100644
--- a/arch/riscv/boot/dts/Makefile
+++ b/arch/riscv/boot/dts/Makefile
@@ -1,5 +1,6 @@
 # SPDX-License-Identifier: GPL-2.0
 subdir-y += sifive
+subdir-y += starfive
 subdir-$(CONFIG_SOC_CANAAN_K210_DTB_BUILTIN) += canaan
 subdir-y += microchip
 
diff --git a/arch/riscv/boot/dts/starfive/Makefile b/arch/riscv/boot/dts/starfive/Makefile
new file mode 100644
index 000000000000..0ea1bc15ab30
--- /dev/null
+++ b/arch/riscv/boot/dts/starfive/Makefile
@@ -0,0 +1,2 @@
+# SPDX-License-Identifier: GPL-2.0
+dtb-$(CONFIG_SOC_STARFIVE) += jh7100-beaglev-starlight.dtb
diff --git a/arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts b/arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts
new file mode 100644
index 000000000000..d30d42d299c6
--- /dev/null
+++ b/arch/riscv/boot/dts/starfive/jh7100-beaglev-starlight.dts
@@ -0,0 +1,162 @@
+// SPDX-License-Identifier: (GPL-2.0 OR MIT)
+/* Copyright (C) 2021 StarFive Technology Co., Ltd. */
+/* Copyright (C) 2021 Emil Renner Berthing <kernel@xxxxxxxx> */
+
+/dts-v1/;
+#include "jh7100.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include <dt-bindings/pinctrl/pinctrl-starfive.h>
+
+/ {
+	model = "BeagleV Starlight Beta";
+	compatible = "beagle,beaglev-starlight-jh7100-r0", "starfive,jh7100";
+
+	aliases {
+		serial0 = &uart3;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	cpus {
+		timebase-frequency = <6250000>;
+	};
+
+	memory@80000000 {
+		device_type = "memory";
+		reg = <0x0 0x80000000 0x2 0x0>;
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led-ack {
+			gpios = <&gpio 43 GPIO_ACTIVE_HIGH>;
+			color = <LED_COLOR_ID_GREEN>;
+			function = LED_FUNCTION_HEARTBEAT;
+			linux,default-trigger = "heartbeat";
+			label = "ack";
+		};
+	};
+};
+
+&gpio {
+	i2c0_pins: i2c0-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(62, GPO_LOW,
+				  GPO_I2C0_PAD_SCK_OEN,
+				  GPI_I2C0_PAD_SCK_IN)>,
+				 <GPIOMUX(61, GPO_LOW,
+				  GPO_I2C0_PAD_SDA_OEN,
+				  GPI_I2C0_PAD_SDA_IN)>;
+			bias-disable; /* external pull-up */
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	i2c1_pins: i2c1-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(47, GPO_LOW,
+				  GPO_I2C1_PAD_SCK_OEN,
+				  GPI_I2C1_PAD_SCK_IN)>,
+				 <GPIOMUX(48, GPO_LOW,
+				  GPO_I2C1_PAD_SDA_OEN,
+				  GPI_I2C1_PAD_SDA_IN)>;
+			bias-pull-up;
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	i2c2_pins: i2c2-0 {
+		i2c-pins {
+			pinmux = <GPIOMUX(60, GPO_LOW,
+				  GPO_I2C2_PAD_SCK_OEN,
+				  GPI_I2C2_PAD_SCK_IN)>,
+				 <GPIOMUX(59, GPO_LOW,
+				  GPO_I2C2_PAD_SDA_OEN,
+				  GPI_I2C2_PAD_SDA_IN)>;
+			bias-disable; /* external pull-up */
+			input-enable;
+			input-schmitt-enable;
+		};
+	};
+
+	uart3_pins: uart3-0 {
+		rx-pin {
+			pinmux = <GPIOMUX(13, GPO_LOW, GPO_DISABLE,
+				  GPI_UART3_PAD_SIN)>;
+			bias-pull-up;
+			drive-strength = <14>;
+			input-enable;
+			input-schmitt-enable;
+			slew-rate = <0>;
+		};
+		tx-pin {
+			pinmux = <GPIOMUX(14, GPO_UART3_PAD_SOUT,
+				  GPO_ENABLE, GPI_NONE)>;
+			bias-disable;
+			drive-strength = <35>;
+			input-disable;
+			input-schmitt-disable;
+			slew-rate = <0>;
+		};
+	};
+};
+
+&i2c0 {
+	clock-frequency = <100000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <500>;
+	i2c-scl-falling-time-ns = <500>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c0_pins>;
+	status = "okay";
+
+	pmic@5e {
+		compatible = "ti,tps65086";
+		reg = <0x5e>;
+		gpio-controller;
+		#gpio-cells = <2>;
+
+		regulators {
+		};
+	};
+};
+
+&i2c1 {
+	clock-frequency = <400000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <100>;
+	i2c-scl-falling-time-ns = <100>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c1_pins>;
+	status = "okay";
+};
+
+&i2c2 {
+	clock-frequency = <100000>;
+	i2c-sda-hold-time-ns = <300>;
+	i2c-sda-falling-time-ns = <500>;
+	i2c-scl-falling-time-ns = <500>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&i2c2_pins>;
+	status = "okay";
+};
+
+&osc_sys {
+	clock-frequency = <25000000>;
+};
+
+&osc_aud {
+	clock-frequency = <27000000>;
+};
+
+&uart3 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart3_pins>;
+	status = "okay";
+};
-- 
2.33.1




[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux