On Mon, Aug 2, 2021 at 5:43 AM Hans de Goede <hdegoede@xxxxxxxxxx> wrote:
>
> Hi Chris,
>
> On 7/6/21 8:47 PM, Chris Blake wrote:
> > This adds platform support for the Cisco Meraki MX100 (Tinkerbell)
> > network appliance. This sets up the network LEDs and Reset
> > button. Note that this patch requires
> > mfd: lpc_ich: Enable GPIO driver for DH89xxCC which has been accepted
> > and is currently targeted for 5.15.
> >
> > Signed-off-by: Chris Blake <chrisrblake93@xxxxxxxxx>
> > Co-developed-by: Christian Lamparter <chunkeey@xxxxxxxxx>
> > ---
> > drivers/platform/x86/Kconfig | 13 ++
> > drivers/platform/x86/Makefile | 3 +
> > drivers/platform/x86/meraki-mx100.c | 185 ++++++++++++++++++++++++++++
> > 3 files changed, 201 insertions(+)
> > create mode 100644 drivers/platform/x86/meraki-mx100.c
> >
> > diff --git a/drivers/platform/x86/Kconfig b/drivers/platform/x86/Kconfig
> > index 7d385c3b2239..8d70176e335f 100644
> > --- a/drivers/platform/x86/Kconfig
> > +++ b/drivers/platform/x86/Kconfig
> > @@ -302,6 +302,19 @@ config ASUS_NB_WMI
> > If you have an ACPI-WMI compatible Asus Notebook, say Y or M
> > here.
> >
> > +config MERAKI_MX100
> > + tristate "Cisco Meraki MX100 Platform Driver"
> > + depends on GPIOLIB
> > + depends on GPIO_ICH
> > + depends on LEDS_CLASS
> > + select LEDS_GPIO
> > + help
> > + This driver provides support for the front button and LEDs on
> > + the Cisco Meraki MX100 (Tinkerbell) 1U appliance.
> > +
> > + To compile this driver as a module, choose M here: the module
> > + will be called meraki-mx100.
> > +
> > config EEEPC_LAPTOP
> > tristate "Eee PC Hotkey Driver"
> > depends on ACPI
> > diff --git a/drivers/platform/x86/Makefile b/drivers/platform/x86/Makefile
> > index 7ee369aab10d..25c5aee1cde7 100644
> > --- a/drivers/platform/x86/Makefile
> > +++ b/drivers/platform/x86/Makefile
> > @@ -39,6 +39,9 @@ obj-$(CONFIG_ASUS_NB_WMI) += asus-nb-wmi.o
> > obj-$(CONFIG_EEEPC_LAPTOP) += eeepc-laptop.o
> > obj-$(CONFIG_EEEPC_WMI) += eeepc-wmi.o
> >
> > +# Cisco/Meraki
> > +obj-$(CONFIG_MERAKI_MX100) += meraki-mx100.o
> > +
> > # Dell
> > obj-$(CONFIG_X86_PLATFORM_DRIVERS_DELL) += dell/
> >
> > diff --git a/drivers/platform/x86/meraki-mx100.c b/drivers/platform/x86/meraki-mx100.c
> > new file mode 100644
> > index 000000000000..12b17ef06d14
> > --- /dev/null
> > +++ b/drivers/platform/x86/meraki-mx100.c
> > @@ -0,0 +1,185 @@
> > +// SPDX-License-Identifier: GPL-2.0+
> > +
> > +/*
> > + * Cisco Meraki MX100 (Tinkerbell) board platform driver
> > + *
> > + * Based off of arch/x86/platform/meraki/tink.c from the
> > + * Meraki GPL release meraki-firmware-sources-r23-20150601
> > + *
> > + * Format inspired by platform/x86/pcengines-apuv2.c
> > + *
> > + * Copyright (C) 2021 Chris Blake <chrisrblake93@xxxxxxxxx>
> > + */
> > +
> > +#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
> > +
> > +#include <linux/dmi.h>
> > +#include <linux/err.h>
> > +#include <linux/gpio.h>
> > +#include <linux/gpio_keys.h>
> > +#include <linux/input.h>
> > +#include <linux/kernel.h>
> > +#include <linux/leds.h>
> > +#include <linux/module.h>
> > +#include <linux/platform_device.h>
> > +
> > +#define TINK_GPIO_OFFSET 436
> > +
> > +/* LEDs */
> > +static const struct gpio_led tink_leds[] = {
> > + {
> > + .name = "mx100:green:internet",
> > + .gpio = TINK_GPIO_OFFSET + 11,
> > + .active_low = 1,
>
> Unfortunately you cannot count on gpio-numbers on x86 devices being stable,
> so you need to drop all the .gpio = *and active_low* settings here,
> instead you need to create + add a gpiod lookup table looking like this:
>
> static struct gpiod_lookup_table gpios_led_table = {
> .dev_id = "leds-gpio",
> .table = {
> GPIO_LOOKUP_IDX("<TINK-gpiochip-dev_id>", 11,
> NULL, 0, GPIO_ACTIVE_LOW),
> GPIO_LOOKUP_IDX("<TINK-gpiochip-dev_id>", 18,
> NULL, 1, GPIO_ACTIVE_HIGH),
> GPIO_LOOKUP_IDX("<TINK-gpiochip-dev_id>", 20,
> NULL, 2, GPIO_ACTIVE_HIGH),
>
> Note the first set of numbers are the pin numbers on the
> TINK gpiochip.
>
> The second set of numbers simply goes 0,1,2,3,4...
> and basically gives the indexes into your tink_leds[] array
> for which this lookup is.
>
> You can use e.g. gpiodetect from libgpiod-utils to find the
> <TINK-gpiochip-dev_id>.
>
> (I assume the GPIO_ACTIVE_FOO field explains itself)
>
> Once you've created the table don't forget to register it
> with gpiod_add_lookup_table() and unregister it again
> on module remove.
>
> > + .default_trigger = "default-on",
> > + },
> > + {
> > + .name = "mx100:green:lan2",
> > + .gpio = TINK_GPIO_OFFSET + 18,
> > + },
> > + {
> > + .name = "mx100:green:lan3",
> > + .gpio = TINK_GPIO_OFFSET + 20,
> > + },
> > + {
> > + .name = "mx100:green:lan4",
> > + .gpio = TINK_GPIO_OFFSET + 22,
> > + },
> > + {
> > + .name = "mx100:green:lan5",
> > + .gpio = TINK_GPIO_OFFSET + 23,
> > + },
> > + {
> > + .name = "mx100:green:lan6",
> > + .gpio = TINK_GPIO_OFFSET + 32,
> > + },
> > + {
> > + .name = "mx100:green:lan7",
> > + .gpio = TINK_GPIO_OFFSET + 34,
> > + },
> > + {
> > + .name = "mx100:green:lan8",
> > + .gpio = TINK_GPIO_OFFSET + 35,
> > + },
> > + {
> > + .name = "mx100:green:lan9",
> > + .gpio = TINK_GPIO_OFFSET + 36,
> > + },
> > + {
> > + .name = "mx100:green:lan10",
> > + .gpio = TINK_GPIO_OFFSET + 37,
> > + },
> > + {
> > + .name = "mx100:green:lan11",
> > + .gpio = TINK_GPIO_OFFSET + 48,
> > + },
> > + {
> > + .name = "mx100:green:ha",
> > + .gpio = TINK_GPIO_OFFSET + 16,
> > + .active_low = 1,
> > + },
> > + {
> > + .name = "mx100:orange:ha",
> > + .gpio = TINK_GPIO_OFFSET + 7,
> > + .active_low = 1,
> > + },
> > + {
> > + .name = "mx100:green:usb",
> > + .gpio = TINK_GPIO_OFFSET + 21,
> > + .active_low = 1,
> > + },
> > + {
> > + .name = "mx100:orange:usb",
> > + .gpio = TINK_GPIO_OFFSET + 19,
> > + .active_low = 1,
> > + },
> > +};
> > +
> > +static const struct gpio_led_platform_data tink_leds_pdata = {
> > + .num_leds = ARRAY_SIZE(tink_leds),
> > + .leds = tink_leds,
> > +};
> > +
> > +/* Reset Button */
> > +static struct gpio_keys_button tink_buttons[] = {
> > + {
> > + .desc = "Reset",
> > + .type = EV_KEY,
> > + .code = KEY_RESTART,
> > + .gpio = TINK_GPIO_OFFSET + 60,
> > + .active_low = 1,
>
> Same remark wrt hardcoding GPIO numbers. Note this needs a separate
> lookup table, see the pcengines-apuv2.c code.
>
> > + .debounce_interval = 100,
> > + },
> > +};
> > +
> > +static const struct gpio_keys_platform_data tink_buttons_pdata = {
> > + .buttons = tink_buttons,
> > + .nbuttons = ARRAY_SIZE(tink_buttons),
> > + .poll_interval = 20,
> > + .rep = 0,
> > + .name = "mx100-keys",
> > +};
> > +
> > +/* Board setup */
> > +
> > +static struct platform_device *tink_leds_pdev;
> > +static struct platform_device *tink_keys_pdev;
> > +
> > +static struct platform_device * __init tink_create_dev(
> > + const char *name,
> > + const void *pdata,
> > + size_t sz)
> > +{
> > + struct platform_device *pdev;
> > +
> > + pdev = platform_device_register_data(NULL,
> > + name,
> > + PLATFORM_DEVID_NONE,
> > + pdata,
> > + sz);
> > +
> > + if (IS_ERR(pdev))
> > + pr_err("failed registering %s: %ld\n", name, PTR_ERR(pdev));
> > +
> > + return pdev;
> > +}
> > +
>
> You probably want to put the following here:
>
> static const struct dmi_system_id tink_systems[] __initconst = {
> {
> .matches = {
> DMI_EXACT_MATCH(DMI_SYS_VENDOR, "Cisco"),
> DMI_EXACT_MATCH(DMI_PRODUCT_NAME, "MX100-HW"),
> },
> },
> {} /* Terminating entry */
> };
> MODULE_DEVICE_TABLE(dmi, tink_systems);
>
> The MODULE_DEVICE_TABLE line will cause the module to get auto-loaded
> on the systems in the table.
>
> > +static int __init tink_board_init(void)
> > +{
> > + if (!dmi_match(DMI_SYS_VENDOR, "Cisco") || !dmi_match(DMI_PRODUCT_NAME, "MX100-HW")) {
> > + return -ENODEV;
> > + }
>
> And then replace this with:
>
> if (!dmi_first_match(tink_systems))
> return -ENODEV;
>
> In case someone tries to load the module manually.
>
> > +
> > + /* We need to make sure that GPIO60 isn't set to native mode as is default since it's our
> > + * Reset Button. To do this, write to GPIO_USE_SEL2 to have GPIO60 set to GPIO mode.
> > + * This is documented on page 1609 of the PCH datasheet, order number 327879-005US
> > + */
> > + outl(inl(0x530) | BIT(28), 0x530);
> > +
> > + tink_leds_pdev = tink_create_dev(
> > + "leds-gpio",
> > + &tink_leds_pdata,
> > + sizeof(tink_leds_pdata));
> > +
> > + tink_keys_pdev = tink_create_dev(
> > + "gpio-keys-polled",
> > + &tink_buttons_pdata,
> > + sizeof(tink_buttons_pdata));
> > +
> > + return 0;
> > +}
> > +
> > +static void __exit tink_board_exit(void)
> > +{
> > + platform_device_unregister(tink_keys_pdev);
> > + platform_device_unregister(tink_leds_pdev);
> > +}
> > +
> > +module_init(tink_board_init);
> > +module_exit(tink_board_exit);
> > +
> > +MODULE_AUTHOR("Chris Blake <chrisrblake93@xxxxxxxxx>");
> > +MODULE_DESCRIPTION("Cisco Meraki MX100 Platform Driver");
> > +MODULE_LICENSE("GPL");
> > +MODULE_ALIAS("platform:meraki-mx100");
>
> > +MODULE_SOFTDEP("pre: platform:gpio_ich platform:leds-gpio platform:gpio_keys_polled");
>
> This softdep line should not be necessary (once you use GPIO lookups) the creation
> of the platform devs will automatically cause the leds-gpio resp gpio_keyS_polled
> modules to get loaded.
>
> Other then the remarks above this looks good to me.
>
> Regards,
>
> Hans
>
Hello Hans,
Thank you so much for the feedback. I'll try to get a version 2 of
this patch out sometime in the next week or so. I appreciate you
taking the time to review this for me.
Regards,
Chris Blake
Re: [PATCH] platform/x86: add meraki-mx100 platform driver
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
- Subject: Re: [PATCH] platform/x86: add meraki-mx100 platform driver
- From: Chris <chrisrblake93@xxxxxxxxx>
- Date: Tue, 3 Aug 2021 21:04:39 -0500
- In-reply-to: <e352bafc-cf31-4cd2-31c8-3c75a96b10d5@redhat.com>
- References: <20210706184730.14951-1-chrisrblake93@gmail.com> <e352bafc-cf31-4cd2-31c8-3c75a96b10d5@redhat.com>
- References:
- [PATCH] platform/x86: add meraki-mx100 platform driver
- From: Chris Blake
- Re: [PATCH] platform/x86: add meraki-mx100 platform driver
- From: Hans de Goede
- [PATCH] platform/x86: add meraki-mx100 platform driver
- Prev by Date: Re: [RFC 08/11] gpiolib: cdev: Add hardware timestamp clock type
- Next by Date: Re: [PATCH V4 3/5] dt-bindings: gpio: Add bindings for gpio-virtio
- Previous by thread: Re: [PATCH] platform/x86: add meraki-mx100 platform driver
- Next by thread: RE: [PATCH v2 2/2] pinctrl: imx8ulp: Add pinctrl driver support
- Index(es):
 |