Re: [PATCH v3 02/10] pinctrl: Ingenic: Add support for read the pin configuration of X1830.

[Zhou Yanjie <zhouyanjie@xxxxxxxxxxxxxx>]

Hi,

On 2021/3/23 上午1:58, Paul Cercueil wrote:
> Le mer. 17 mars 2021 à 17:57, 周琰杰 (Zhou Yanjie) 
> <zhouyanjie@xxxxxxxxxxxxxx> a écrit :
> > Add X1830 support in "ingenic_pinconf_get()", so that it can read the
> > configuration of X1830 SoC correctly.
> >
> > Fixes: d7da2a1e4e08 ("pinctrl: Ingenic: Add pinctrl driver for X1830.")
> >
> > Signed-off-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@xxxxxxxxxxxxxx>
> > ---
> >
> > Notes:
> >     v2:
> >     New patch.
> >
> >     v2->v3:
> >     1.Add fixes tag.
> >     2.Adjust the code, simplify the ingenic_pinconf_get() function.
> >
> >  drivers/pinctrl/pinctrl-ingenic.c | 38 
> > ++++++++++++++++++++++++++++++--------
> >  1 file changed, 30 insertions(+), 8 deletions(-)
> >
> > diff --git a/drivers/pinctrl/pinctrl-ingenic.c 
> > b/drivers/pinctrl/pinctrl-ingenic.c
> > index 05dfa0a..1d43b98 100644
> > --- a/drivers/pinctrl/pinctrl-ingenic.c
> > +++ b/drivers/pinctrl/pinctrl-ingenic.c
> > @@ -2109,26 +2109,48 @@ static int ingenic_pinconf_get(struct 
> > pinctrl_dev *pctldev,
> >      enum pin_config_param param = pinconf_to_config_param(*config);
> >      unsigned int idx = pin % PINS_PER_GPIO_CHIP;
> >      unsigned int offt = pin / PINS_PER_GPIO_CHIP;
> > -    bool pull;
> > +    unsigned int bias;
> > +    bool pull, pullup, pulldown;
> >
> > -    if (jzpc->info->version >= ID_JZ4770)
> > -        pull = !ingenic_get_pin_config(jzpc, pin, JZ4770_GPIO_PEN);
> > -    else
> > -        pull = !ingenic_get_pin_config(jzpc, pin, 
> > JZ4740_GPIO_PULL_DIS);
> > +    if (jzpc->info->version >= ID_X1830) {
> > +        unsigned int half = PINS_PER_GPIO_CHIP / 2;
> > +        unsigned int idxh = pin % half * 2;
>
> I had to look up operator precedence in C, '*' and '%' have the same 
> priority so this reads left-to-right.
>
> I'd suggest adding parentheses around the '%' to make it more obvious.

Sure.


> With that:
>
> Reviewed-by: Paul Cercueil <paul@xxxxxxxxxxxxxxx>
>
> Cheers,
> -Paul
>
> > +
> > +        if (idx < half)
> > +            regmap_read(jzpc->map, offt * jzpc->info->reg_offset +
> > +                    X1830_GPIO_PEL, &bias);
> > +        else
> > +            regmap_read(jzpc->map, offt * jzpc->info->reg_offset +
> > +                    X1830_GPIO_PEH, &bias);
> > +
> > +        bias = (bias >> idxh) & (GPIO_PULL_UP | GPIO_PULL_DOWN);
> > +
> > +        pullup = (bias == GPIO_PULL_UP) && 
> > (jzpc->info->pull_ups[offt] & BIT(idx));
> > +        pulldown = (bias == GPIO_PULL_DOWN) && 
> > (jzpc->info->pull_downs[offt] & BIT(idx));
> > +
> > +    } else {
> > +        if (jzpc->info->version >= ID_JZ4770)
> > +            pull = !ingenic_get_pin_config(jzpc, pin, JZ4770_GPIO_PEN);
> > +        else
> > +            pull = !ingenic_get_pin_config(jzpc, pin, 
> > JZ4740_GPIO_PULL_DIS);
> > +
> > +        pullup = pull && (jzpc->info->pull_ups[offt] & BIT(idx));
> > +        pulldown = pull && (jzpc->info->pull_downs[offt] & BIT(idx));
> > +    }
> >
> >      switch (param) {
> >      case PIN_CONFIG_BIAS_DISABLE:
> > -        if (pull)
> > +        if (pullup || pulldown)
> >              return -EINVAL;
> >          break;
> >
> >      case PIN_CONFIG_BIAS_PULL_UP:
> > -        if (!pull || !(jzpc->info->pull_ups[offt] & BIT(idx)))
> > +        if (!pullup)
> >              return -EINVAL;
> >          break;
> >
> >      case PIN_CONFIG_BIAS_PULL_DOWN:
> > -        if (!pull || !(jzpc->info->pull_downs[offt] & BIT(idx)))
> > +        if (!pulldown)
> >              return -EINVAL;
> >          break;
> >
> > --
> > 2.7.4