On 04/03/2021 04:41, Brad Larson wrote:
> Add Pensando common and Elba SoC specific device nodes
> and corresponding binding documentation.
>
> Signed-off-by: Brad Larson <brad@xxxxxxxxxxx>
> ---
> .../bindings/gpio/pensando,elba-spics.txt | 24 ++
> .../devicetree/bindings/mmc/cdns,sdhci.yaml | 2 +-
> .../bindings/spi/cadence-quadspi.txt | 1 +
> .../devicetree/bindings/vendor-prefixes.yaml | 2 +
Hi,
dt-bindings go always to separate patches, at beginning of patchset.
> arch/arm64/boot/dts/Makefile | 1 +
> arch/arm64/boot/dts/pensando/Makefile | 6 +
> arch/arm64/boot/dts/pensando/elba-16core.dtsi | 171 ++++++++++
> .../boot/dts/pensando/elba-asic-common.dtsi | 113 +++++++
> arch/arm64/boot/dts/pensando/elba-asic.dts | 8 +
> .../boot/dts/pensando/elba-flash-parts.dtsi | 80 +++++
> arch/arm64/boot/dts/pensando/elba.dtsi | 310 ++++++++++++++++++
You need the board/vendor YAML file. See:
Documentation/devicetree/bindings/arm/
> 11 files changed, 717 insertions(+), 1 deletion(-)
> create mode 100644 Documentation/devicetree/bindings/gpio/pensando,elba-spics.txt
> create mode 100644 arch/arm64/boot/dts/pensando/Makefile
> create mode 100644 arch/arm64/boot/dts/pensando/elba-16core.dtsi
> create mode 100644 arch/arm64/boot/dts/pensando/elba-asic-common.dtsi
> create mode 100644 arch/arm64/boot/dts/pensando/elba-asic.dts
> create mode 100644 arch/arm64/boot/dts/pensando/elba-flash-parts.dtsi
> create mode 100644 arch/arm64/boot/dts/pensando/elba.dtsi
>
> diff --git a/Documentation/devicetree/bindings/gpio/pensando,elba-spics.txt b/Documentation/devicetree/bindings/gpio/pensando,elba-spics.txt
> new file mode 100644
> index 000000000000..30f5f3275238
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/pensando,elba-spics.txt
> @@ -0,0 +1,24 @@
> +Pensando Elba SPI Chip Select Driver
> +
> +The Pensando Elba ASIC provides four SPI bus chip selects
> +
> +Required properties:
> +- compatible: Should be "pensando,elba-spics"
> +- reg: Address range of spics controller
> +- gpio-controller: Marks the device node as gpio controller
> +- #gpio-cells: Must be 2
> +
> +Example:
> +-------
> +spics: spics@307c2468 {
> + compatible = "pensando,elba-spics";
> + reg = <0x0 0x307c2468 0x0 0x4>;
> + gpio-controller;
> + #gpio-cells = <2>;
> +};
> +
> +&spi0 {
> + num-cs = <4>;
> + cs-gpios = <&spics 0 0>, <&spics 1 0>, <&porta 1 0>, <&porta 7 0>;
> + ...
> +}
> diff --git a/Documentation/devicetree/bindings/mmc/cdns,sdhci.yaml b/Documentation/devicetree/bindings/mmc/cdns,sdhci.yaml
> index af7442f73881..645ae696ba24 100644
> --- a/Documentation/devicetree/bindings/mmc/cdns,sdhci.yaml
> +++ b/Documentation/devicetree/bindings/mmc/cdns,sdhci.yaml
> @@ -122,7 +122,7 @@ unevaluatedProperties: false
> examples:
> - |
> emmc: mmc@5a000000 {
> - compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc";
> + compatible = "socionext,uniphier-sd4hc", "cdns,sd4hc", "pensando,elba-emmc";
Why are you doing this?
> reg = <0x5a000000 0x400>;
> interrupts = <0 78 4>;
> clocks = <&clk 4>;
> diff --git a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> index 8ace832a2d80..dbb346b2b1d7 100644
> --- a/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> +++ b/Documentation/devicetree/bindings/spi/cadence-quadspi.txt
> @@ -6,6 +6,7 @@ Required properties:
> For TI 66AK2G SoC - "ti,k2g-qspi", "cdns,qspi-nor".
> For TI AM654 SoC - "ti,am654-ospi", "cdns,qspi-nor".
> For Intel LGM SoC - "intel,lgm-qspi", "cdns,qspi-nor".
> + For Pensando SoC - "pensando,cdns-qspi".
> - reg : Contains two entries, each of which is a tuple consisting of a
> physical address and length. The first entry is the address and
> length of the controller register set. The second entry is the
> diff --git a/Documentation/devicetree/bindings/vendor-prefixes.yaml b/Documentation/devicetree/bindings/vendor-prefixes.yaml
> index f6064d84a424..9a21d780c5e1 100644
> --- a/Documentation/devicetree/bindings/vendor-prefixes.yaml
> +++ b/Documentation/devicetree/bindings/vendor-prefixes.yaml
> @@ -850,6 +850,8 @@ patternProperties:
> description: Parallax Inc.
> "^pda,.*":
> description: Precision Design Associates, Inc.
> + "^pensando,.*":
> + description: Pensando Systems Inc.
> "^pericom,.*":
> description: Pericom Technology Inc.
> "^pervasive,.*":
> diff --git a/arch/arm64/boot/dts/Makefile b/arch/arm64/boot/dts/Makefile
> index f1173cd93594..c85db0a097fe 100644
> --- a/arch/arm64/boot/dts/Makefile
> +++ b/arch/arm64/boot/dts/Makefile
> @@ -19,6 +19,7 @@ subdir-y += marvell
> subdir-y += mediatek
> subdir-y += microchip
> subdir-y += nvidia
> +subdir-y += pensando
> subdir-y += qcom
> subdir-y += realtek
> subdir-y += renesas
> diff --git a/arch/arm64/boot/dts/pensando/Makefile b/arch/arm64/boot/dts/pensando/Makefile
> new file mode 100644
> index 000000000000..0c2c0961e64a
> --- /dev/null
> +++ b/arch/arm64/boot/dts/pensando/Makefile
> @@ -0,0 +1,6 @@
> +# SPDX-License-Identifier: GPL-2.0
> +dtb-$(CONFIG_ARCH_PENSANDO_ELBA_SOC) += elba-asic.dtb
> +
> +always-y := $(dtb-y)
> +subdir-y := $(dts-dirs)
> +clean-files := *.dtb
> diff --git a/arch/arm64/boot/dts/pensando/elba-16core.dtsi b/arch/arm64/boot/dts/pensando/elba-16core.dtsi
> new file mode 100644
> index 000000000000..b0386864cfec
> --- /dev/null
> +++ b/arch/arm64/boot/dts/pensando/elba-16core.dtsi
> @@ -0,0 +1,171 @@
> +// SPDX-License-Identifier: GPL-2.0
> +
> +/ {
> + cpus {
> + #address-cells = <2>;
> + #size-cells = <0>;
> +
> + cpu-map {
> + cluster0 {
> + core0 { cpu = <&cpu0>; };
> + core1 { cpu = <&cpu1>; };
> + core2 { cpu = <&cpu2>; };
> + core3 { cpu = <&cpu3>; };
> + };
> + cluster1 {
> + core0 { cpu = <&cpu4>; };
> + core1 { cpu = <&cpu5>; };
> + core2 { cpu = <&cpu6>; };
> + core3 { cpu = <&cpu7>; };
> + };
> + cluster2 {
> + core0 { cpu = <&cpu8>; };
> + core1 { cpu = <&cpu9>; };
> + core2 { cpu = <&cpu10>; };
> + core3 { cpu = <&cpu11>; };
> + };
> + cluster3 {
> + core0 { cpu = <&cpu12>; };
> + core1 { cpu = <&cpu13>; };
> + core2 { cpu = <&cpu14>; };
> + core3 { cpu = <&cpu15>; };
> + };
> + };
> +
> + // CLUSTER 0
> + cpu0: cpu@0 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72", "arm,armv8";
> + reg = <0 0x0>;
> + enable-method = "spin-table";
> + next-level-cache = <&l2_0>;
> + };
> + cpu1: cpu@1 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72", "arm,armv8";
> + reg = <0 0x1>;
> + enable-method = "spin-table";
> + next-level-cache = <&l2_0>;
> + };
> + cpu2: cpu@2 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72", "arm,armv8";
> + reg = <0 0x2>;
> + enable-method = "spin-table";
> + next-level-cache = <&l2_0>;
> + };
> + cpu3: cpu@3 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72", "arm,armv8";
> + reg = <0 0x3>;
> + enable-method = "spin-table";
> + next-level-cache = <&l2_0>;
> + };
> +
> + l2_0: l2-cache0 {
> + compatible = "cache";
> + };
> +
> + // CLUSTER 1
> + cpu4: cpu@100 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72", "arm,armv8";
> + reg = <0 0x100>;
> + enable-method = "spin-table";
> + next-level-cache = <&l2_1>;
> + };
> + cpu5: cpu@101 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72", "arm,armv8";
> + reg = <0 0x101>;
> + enable-method = "spin-table";
> + next-level-cache = <&l2_1>;
> + };
> + cpu6: cpu@102 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72", "arm,armv8";
> + reg = <0 0x102>;
> + enable-method = "spin-table";
> + next-level-cache = <&l2_1>;
> + };
> + cpu7: cpu@103 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72", "arm,armv8";
> + reg = <0 0x103>;
> + enable-method = "spin-table";
> + next-level-cache = <&l2_1>;
> + };
> +
> + l2_1: l2-cache1 {
> + compatible = "cache";
> + };
> +
> + // CLUSTER 2
> + cpu8: cpu@200 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72", "arm,armv8";
> + reg = <0 0x200>;
> + enable-method = "spin-table";
> + next-level-cache = <&l2_2>;
> + };
> + cpu9: cpu@201 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72", "arm,armv8";
> + reg = <0 0x201>;
> + enable-method = "spin-table";
> + next-level-cache = <&l2_2>;
> + };
> + cpu10: cpu@202 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72", "arm,armv8";
> + reg = <0 0x202>;
> + enable-method = "spin-table";
> + next-level-cache = <&l2_2>;
> + };
> + cpu11: cpu@203 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72", "arm,armv8";
> + reg = <0 0x203>;
> + enable-method = "spin-table";
> + next-level-cache = <&l2_2>;
> + };
> +
> + l2_2: l2-cache2 {
> + compatible = "cache";
> + };
> +
> + // CLUSTER 3
> + cpu12: cpu@300 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72", "arm,armv8";
> + reg = <0 0x300>;
> + enable-method = "spin-table";
> + next-level-cache = <&l2_3>;
> + };
> + cpu13: cpu@301 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72", "arm,armv8";
> + reg = <0 0x301>;
> + enable-method = "spin-table";
> + next-level-cache = <&l2_3>;
> + };
> + cpu14: cpu@302 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72", "arm,armv8";
> + reg = <0 0x302>;
> + enable-method = "spin-table";
> + next-level-cache = <&l2_3>;
> + };
> + cpu15: cpu@303 {
> + device_type = "cpu";
> + compatible = "arm,cortex-a72", "arm,armv8";
> + reg = <0 0x303>;
> + enable-method = "spin-table";
> + next-level-cache = <&l2_3>;
> + };
> +
> + l2_3: l2-cache3 {
> + compatible = "cache";
> + };
Run the dtbs_check and build dtbs with W=1 - no warnings are usually
expected.
> + };
> +};
> diff --git a/arch/arm64/boot/dts/pensando/elba-asic-common.dtsi b/arch/arm64/boot/dts/pensando/elba-asic-common.dtsi
> new file mode 100644
> index 000000000000..9623df208131
> --- /dev/null
> +++ b/arch/arm64/boot/dts/pensando/elba-asic-common.dtsi
> @@ -0,0 +1,113 @@
> +// SPDX-License-Identifier: GPL-2.0
> +
> +/ {
> + model = "Elba ASIC Board";
> +
> + aliases {
> + serial0 = &uart0;
> + spi0 = &spi0;
> + spi1 = &qspi;
> + };
> +
> + chosen {
> + stdout-path = "serial0:19200n8";
> + };
> +};
> +
> +&ahb_clk {
> + clock-frequency = <400000000>;
> +};
> +
> +&emmc_clk {
> + clock-frequency = <200000000>;
> +};
> +
> +&flash_clk {
> + clock-frequency = <400000000>;
> +};
> +
> +&ref_clk {
> + clock-frequency = <156250000>;
> +};
> +
> +&qspi {
> + status = "okay";
> + flash0: mt25q@0 {
> + compatible = "jdec,spi-nor";
> + reg = <0>;
> + spi-max-frequency = <40000000>;
> + spi-rx-bus-width = <2>;
> + m25p,fast-read;
> + cdns,read-delay = <0>;
> + cdns,tshsl-ns = <0>;
> + cdns,tsd2d-ns = <0>;
> + cdns,tchsh-ns = <0>;
> + cdns,tslch-ns = <0>;
> + };
> +};
> +
> +&gpio0 {
> + status = "ok";
> +};
> +
> +&emmc {
> + bus-width = <8>;
> + status = "ok";
> +};
> +
> +&wdt0 {
> + status = "okay";
> +};
> +
> +&i2c0 {
> + clock-frequency = <100000>;
> + status = "okay";
> + tmp451@4c {
Generic node name needed, like in devicetree spec.
> + compatible = "ti,tmp451";
> + reg = <0x4c>;
> + };
Here and everywhere else - line break between each node.
> + tps53659@62 {
> + compatible = "ti,tps53659";
> + reg = <0x62>;
> + };
> + pcf85263@51 {
> + compatible = "nxp,pcf85263";
> + reg = <0x51>;
> + };
> +};
> +
> +&spi0 {
> + num-cs = <4>;
> + cs-gpios = <&spics 0 0>, <&spics 1 0>, <&porta 1 0>, <&porta 7 0>;
> + status = "okay";
> + spi@0 {
> + compatible = "pensando,cpld";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + spi-max-frequency = <12000000>;
> + reg = <0>;
> + };
> + spi@1 {
> + compatible = "pensando,cpld";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + spi-max-frequency = <12000000>;
> + reg = <1>;
> + };
> + spi@2 {
> + compatible = "pensando,cpld-rd1173";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + spi-max-frequency = <12000000>;
> + reg = <2>;
> + interrupt-parent = <&porta>;
> + interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
> + };
> + spi@3 {
> + compatible = "pensando,cpld";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + spi-max-frequency = <12000000>;
> + reg = <3>;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/pensando/elba-asic.dts b/arch/arm64/boot/dts/pensando/elba-asic.dts
> new file mode 100644
> index 000000000000..411c48457006
> --- /dev/null
> +++ b/arch/arm64/boot/dts/pensando/elba-asic.dts
> @@ -0,0 +1,8 @@
> +// SPDX-License-Identifier: GPL-2.0
> +
> +/dts-v1/;
> +
> +#include "elba.dtsi"
> +#include "elba-16core.dtsi"
> +#include "elba-asic-common.dtsi"
> +#include "elba-flash-parts.dtsi"
> diff --git a/arch/arm64/boot/dts/pensando/elba-flash-parts.dtsi b/arch/arm64/boot/dts/pensando/elba-flash-parts.dtsi
> new file mode 100644
> index 000000000000..1983de1a8403
> --- /dev/null
> +++ b/arch/arm64/boot/dts/pensando/elba-flash-parts.dtsi
> @@ -0,0 +1,80 @@
> +// SPDX-License-Identifier: GPL-2.0
> +
> +&flash0 {
> + partitions {
> + compatible = "fixed-partitions";
> + #address-cells = <1>;
> + #size-cells = <1>;
> + partition@0 {
> + label = "flash";
> + reg = <0x00010000 0x0fff0000>;
> + };
> + partition@f0000 {
> + label = "golduenv";
> + reg = <0x000f0000 0x00010000>;
> + };
> + partition@100000 {
> + label = "boot0";
> + reg = <0x00100000 0x00080000>;
> + };
> + partition@180000 {
> + label = "golduboot";
> + reg = <0x00180000 0x00200000>;
> + };
> + partition@400000 {
> + label = "goldfw";
> + reg = <0x00400000 0x03c00000>;
> + };
> + partition@4010000 {
> + label = "fwmap";
> + reg = <0x04010000 0x00020000>;
> + };
> + partition@4030000 {
> + label = "fwsel";
> + reg = <0x04030000 0x00020000>;
> + };
> + partition@4090000 {
> + label = "bootlog";
> + reg = <0x04090000 0x00020000>;
No leading 0 in address and size.
> + };
> + partition@40b0000 {
> + label = "panicbuf";
> + reg = <0x040b0000 0x00020000>;
> + };
> + partition@40d0000 {
> + label = "uservars";
> + reg = <0x040d0000 0x00020000>;
> + };
> + partition@4200000 {
> + label = "uboota";
> + reg = <0x04200000 0x00400000>;
> + };
> + partition@4600000 {
> + label = "ubootb";
> + reg = <0x04600000 0x00400000>;
> + };
> + partition@4a00000 {
> + label = "mainfwa";
> + reg = <0x04a00000 0x01000000>;
> + };
> + partition@5a00000 {
> + label = "mainfwb";
> + reg = <0x05a00000 0x01000000>;
> + };
> + partition@8000000 {
> + label = "diagfw";
> + reg = <0x08000000 0x07fe0000>;
> + };
> + partition@ffe0000 {
> + label = "ubootenv";
> + reg = <0x0ffe0000 0x00010000>;
> + };
> + };
> +};
> +
> +&soc {
> + panicdump@740b0000 {
> + compatible = "pensando,capri-crash";
> + reg = <0x0 0x740b0000 0x0 0x00020000>;
> + };
> +};
> diff --git a/arch/arm64/boot/dts/pensando/elba.dtsi b/arch/arm64/boot/dts/pensando/elba.dtsi
> new file mode 100644
> index 000000000000..72245e279483
> --- /dev/null
> +++ b/arch/arm64/boot/dts/pensando/elba.dtsi
> @@ -0,0 +1,310 @@
> +// SPDX-License-Identifier: GPL-2.0
> +/*
> + * Copyright (c) 2019-2021, Pensando Systems Inc.
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
You have SPDX header. No boiler plate.
OK, I stopped...
Best regards,
Krzysztof
Re: [PATCH 7/8] arm64: dts: Add Pensando Elba SoC support
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
- Subject: Re: [PATCH 7/8] arm64: dts: Add Pensando Elba SoC support
- From: Krzysztof Kozlowski <krzysztof.kozlowski@xxxxxxxxxxxxx>
- Date: Fri, 5 Mar 2021 12:22:45 +0100
- In-reply-to: <20210304034141.7062-8-brad@pensando.io>
- References: <20210304034141.7062-1-brad@pensando.io> <20210304034141.7062-8-brad@pensando.io>
- User-agent: Mozilla/5.0 (X11; Linux x86_64; rv:78.0) Gecko/20100101 Thunderbird/78.7.1
- References:
- [PATCH 0/8] Support Pensando Elba SoC
- From: Brad Larson
- [PATCH 7/8] arm64: dts: Add Pensando Elba SoC support
- From: Brad Larson
- [PATCH 0/8] Support Pensando Elba SoC
- Prev by Date: Re: [PATCH v2 08/12] drivers: export device_is_bound()
- Next by Date: Re: [PATCH 1/8] gpio: Add Elba SoC gpio driver for spi cs control
- Previous by thread: Re: [PATCH 7/8] arm64: dts: Add Pensando Elba SoC support
- Next by thread: [PATCH 6/8] arm64: Add config for Pensando SoC platforms
- Index(es):
 |