Document DT bindings for ROHM BD71815. BD71815 is a single-chip power management IC mainly for battery-powered portable devices. The IC integrates 5 bucks, 7 LDOs, a boost driver for LED, a battery charger with a Coulomb counter, a real-time clock, a 32kHz clock and two general-purpose outputs although only one is documented by the data-sheet. Signed-off-by: Matti Vaittinen <matti.vaittinen@xxxxxxxxxxxxxxxxx> --- Changes since v1: - fixed patch ordering to meet ref dependencies - added missing blank lines - clkout-mode changed from string to tristated (uint) - added default for rsense resistor .../bindings/mfd/rohm,bd71815-pmic.yaml | 202 ++++++++++++++++++ 1 file changed, 202 insertions(+) create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml b/Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml new file mode 100644 index 000000000000..b52b8585d48d --- /dev/null +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71815-pmic.yaml @@ -0,0 +1,202 @@ +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mfd/rohm,bd71815-pmic.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ROHM BD71815 Power Management Integrated Circuit bindings + +maintainers: + - Matti Vaittinen <matti.vaittinen@xxxxxxxxxxxxxxxxx> + +description: | + BD71815AGW is a single-chip power management ICs for battery-powered + portable devices. It integrates 5 buck converters, 8 LDOs, a boost driver + for LED and a 500 mA single-cell linear charger. Also included is a Coulomb + counter, a real-time clock (RTC), and a 32.768 kHz clock gate and two GPOs. + +properties: + compatible: + const: rohm,bd71815 + + reg: + description: + I2C slave address. + maxItems: 1 + + interrupts: + maxItems: 1 + + gpio-controller: true + + "#gpio-cells": + const: 2 + description: | + The first cell is the pin number and the second cell is used to specify + flags. See ../gpio/gpio.txt for more information. + + clocks: + maxItems: 1 + + "#clock-cells": + const: 0 + + clock-output-names: + const: bd71815-32k-out + + rohm,clkout-open-drain: + description: clk32kout mode. Set to 1 for "open-drain" or 0 for "cmos". + $ref: "/schemas/types.yaml#/definitions/uint32" + minimum: 0 + maximum: 1 + + rohm,charger-sense-resistor-ohms: + minimum: 10000000 + maximum: 50000000 + description: | + BD71827 and BD71828 have SAR ADC for measuring charging currents. + External sense resistor (RSENSE in data sheet) should be used. If + something other but 30MOhm resistor is used the resistance value + should be given + here in Ohms. + default: 30000000 + + regulators: + $ref: ../regulator/rohm,bd71815-regulator.yaml + description: + List of child nodes that specify the regulators. + + gpio-reserved-ranges: + description: | + Usage of BD71828 GPIO pins can be changed via OTP. This property can be + used to mark the pins which should not be configured for GPIO. Please see + the ../gpio/gpio.txt for more information. + + rohm,enable-hidden-gpo: + description: | + The BD71815 has undocumented GPO at pin E5. Pin is marked as GND at the + data-sheet as it's location in the middle of GND pins makes it hard to + use on PCB. If your board has managed to use this pin you can enable the + second GPO by defining this property. Dont enable this if you are unsure + about how the E5 pin is connected on your board. + type: boolean + +required: + - compatible + - reg + - interrupts + - clocks + - "#clock-cells" + - regulators + - gpio-controller + - "#gpio-cells" + +additionalProperties: false + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/leds/common.h> + i2c { + #address-cells = <1>; + #size-cells = <0>; + pmic: pmic@4b { + compatible = "rohm,bd71815"; + reg = <0x4b>; + + interrupt-parent = <&gpio1>; + interrupts = <29 IRQ_TYPE_LEVEL_LOW>; + + clocks = <&osc 0>; + #clock-cells = <0>; + clock-output-names = "bd71815-32k-out"; + + gpio-controller; + #gpio-cells = <2>; + + rohm,charger-sense-resistor-ohms = <10000000>; + + regulators { + buck1: buck1 { + regulator-name = "buck1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <2000000>; + regulator-always-on; + regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <1150000>; + rohm,dvs-suspend-voltage = <950000>; + }; + buck2: buck2 { + regulator-name = "buck2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <2000000>; + regulator-always-on; + regulator-ramp-delay = <1250>; + rohm,dvs-run-voltage = <1150000>; + rohm,dvs-suspend-voltage = <950000>; + }; + buck3: buck3 { + regulator-name = "buck3"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <2700000>; + regulator-always-on; + }; + buck4: buck4 { + regulator-name = "buck4"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1850000>; + regulator-always-on; + }; + buck5: buck5 { + regulator-name = "buck5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + ldo1: ldo1 { + regulator-name = "ldo1"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + ldo2: ldo2 { + regulator-name = "ldo2"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + ldo3: ldo3 { + regulator-name = "ldo3"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + ldo4: ldo4 { + regulator-name = "ldo4"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + ldo5: ldo5 { + regulator-name = "ldo5"; + regulator-min-microvolt = <800000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + ldo6: ldodvref { + regulator-name = "ldodvref"; + regulator-always-on; + }; + ldo7: ldolpsr { + regulator-name = "ldolpsr"; + regulator-always-on; + }; + + boost: wled { + regulator-name = "wled"; + regulator-min-microamp = <10>; + regulator-max-microamp = <25000>; + }; + }; + }; + }; -- 2.25.4 -- Matti Vaittinen, Linux device drivers ROHM Semiconductors, Finland SWDC Kiviharjunlenkki 1E 90220 OULU FINLAND ~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~ Simon says - in Latin please. ~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~ Thanks to Simon Glass for the translation =]
[PATCH v2 07/17] dt_bindings: mfd: Add ROHM BD71815 PMIC
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
- Subject: [PATCH v2 07/17] dt_bindings: mfd: Add ROHM BD71815 PMIC
- From: Matti Vaittinen <matti.vaittinen@xxxxxxxxxxxxxxxxx>
- Date: Tue, 19 Jan 2021 09:21:23 +0200
- In-reply-to: <cover.1611037866.git.matti.vaittinen@fi.rohmeurope.com>
- References: <cover.1611037866.git.matti.vaittinen@fi.rohmeurope.com>
- Follow-Ups:
- Re: [PATCH v2 07/17] dt_bindings: mfd: Add ROHM BD71815 PMIC
- From: Rob Herring
- Re: [PATCH v2 07/17] dt_bindings: mfd: Add ROHM BD71815 PMIC
- References:
- [PATCH v2 00/17] Support ROHM BD71815 PMIC
- From: Matti Vaittinen
- [PATCH v2 00/17] Support ROHM BD71815 PMIC
- Prev by Date: [PATCH v2 04/17] mfd: bd718x7: simplify by cleaning unnecessary device data
- Next by Date: [PATCH v2 08/17] mfd: Add ROHM BD71815 ID
- Previous by thread: Re: [PATCH v2 04/17] mfd: bd718x7: simplify by cleaning unnecessary device data
- Next by thread: Re: [PATCH v2 07/17] dt_bindings: mfd: Add ROHM BD71815 PMIC
- Index(es):
 |