Re: [PATCH 13/18] ipu3-cio2: Add functionality allowing software_node connections to sensors on platforms designed for Windows

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Sakari - sorry for delayed reply. I didn't get this email actually,
just spotted it on the newsgroup by chance.

On 15/12/2020 22:02, Sakari Ailus wrote:
> Hi Daniel,
> 
> On Tue, Dec 15, 2020 at 10:28:59AM +0000, Daniel Scally wrote:
>> Morning Sakari
>>
>> On 30/11/2020 20:35, Sakari Ailus wrote:
>>>> +/*
>>>> + * Extend this array with ACPI Hardware ID's of devices known to be working.
>>>> + * Do not add a HID for a sensor that is not actually supported.
>>>> + */
>>>> +static const char * const cio2_supported_devices[] = {
>>>> +	"INT33BE",
>>>> +	"OVTI2680",
>>>
>>> I guess we don't have the known-good frequencies for the CSI-2 bus in
>>> firmware?
>>>
>>> One option would be to put there what the drivers currently use. This
>>> assumes the support for these devices is, well, somewhat opportunistic but
>>> I guess there's no way around that right now at least.
>>>
>>> As the systems are laptops, they're likely somewhat less prone to EMI
>>> issues to begin with than mobile phones anyway.
>>
>> Just looking at this; we're currently using this with the ov2680 driver
>> that's in mainline currently (with very minor tweaks) plus a
>> hacked-into-roughly-working version of the atomisp-ov5693 driver (ACPI
>> ID INT33BE = ov5693 physical device). Neither of those drivers lists any
>> link frequencies, nor provides a link frequency control for v4l2 to work
>> with.
>>
>> On the other hand, the ov5648 [1] and ov8865 [2] drivers which Paul has
>> submitted recently, which we also want to be able to support, _do_
>> include that. I can register the frequencies Paul's defined there as a
>> link-frequencies property but this gives rise to two questions:
>>
>>
>> 1. Is this _mandatory_? Do I need to be finding the link-frequencies for
>> the OV2680 and OV5693 drivers too? Or can I skip that property where the
>> driver doesn't handle it anyway. Seems to be working fine without
>> controlling it in driver.
> 
> Receiver drivers generally need the information to program the receiver
> timing. It may work for you without using the correct frequency, but the
> risk of failure on another unit increases.

Hmm, ok. I'll see if I can find the correct values then to add to the
existing drivers.

>> 2. Can I trust all the values in the drivers to be available on each
>> platform? For example for the ov5648 Paul lists these as available:
>>
>>  938static const s64 ov5648_link_freq_menu[] = {
>>
>>
>>  939        210000000,
>>
>>
>>  940        168000000,
>>
>>
>>  941};
>>
>> But can I safely register a link-frequencies property for both of those
>> and trust that that'll work on all IPU3 platforms with an ov5648 in them?
> 
> Ideally we'd know which frequency Windows uses, and use the same.
> 
> Using another frequency may have adverse effects elsewhere in the system.
> AFAIU mostly this concerns radios of all sorts.
> 
> Now that this is in the kernel in any case, it can be fixed later on so I'm
> not too worried about it. Having still a comment there that the
> configuration is opportunistic would be nice.
> 

Understood - I'll add in the ability to add the link-frequencies plus a
comment explaining.

Thanks
Dan




[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux