Re: [PATCH] pinctrl: at91-pio4: add support for fewer lines on last PIO bank

[Ludovic Desroches <ludovic.desroches@xxxxxxxxxxxxx>]

On Fri, Nov 13, 2020 at 03:24:29PM +0200, Eugen Hristev wrote:
> Some products, like sama7g5, do not have a full last bank of PIO lines.
> In this case for example, sama7g5 only has 8 lines for the PE bank.
> PA0-31, PB0-31, PC0-31, PD0-31, PE0-7, in total 136 lines.
> To cope with this situation, added a data attribute that is product dependent,
> to specify the number of lines of the last bank.
> In case this number is different from the macro ATMEL_PIO_NPINS_PER_BANK,
> adjust the total number of lines accordingly.
> This will avoid advertising 160 lines instead of the actual 136, as this
> product supports, and to avoid reading/writing to invalid register addresses.
> 
> Signed-off-by: Eugen Hristev <eugen.hristev@xxxxxxxxxxxxx>

Acked-by: Ludovic Desroches <ludovic.desroches@xxxxxxxxxxxxx>

Thanks.

> ---
>  drivers/pinctrl/pinctrl-at91-pio4.c | 18 ++++++++++++++++--
>  1 file changed, 16 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/pinctrl/pinctrl-at91-pio4.c b/drivers/pinctrl/pinctrl-at91-pio4.c
> index 578b387100d9..d267367d94b9 100644
> --- a/drivers/pinctrl/pinctrl-at91-pio4.c
> +++ b/drivers/pinctrl/pinctrl-at91-pio4.c
> @@ -71,8 +71,15 @@
>  /* Custom pinconf parameters */
>  #define ATMEL_PIN_CONFIG_DRIVE_STRENGTH	(PIN_CONFIG_END + 1)
>  
> +/**
> + * struct atmel_pioctrl_data - Atmel PIO controller (pinmux + gpio) data struct
> + * @nbanks: number of PIO banks
> + * @last_bank_count: number of lines in the last bank (can be less than
> + *	the rest of the banks).
> + */
>  struct atmel_pioctrl_data {
>  	unsigned nbanks;
> +	unsigned last_bank_count;
>  };
>  
>  struct atmel_group {
> @@ -980,11 +987,13 @@ static const struct dev_pm_ops atmel_pctrl_pm_ops = {
>   * We can have up to 16 banks.
>   */
>  static const struct atmel_pioctrl_data atmel_sama5d2_pioctrl_data = {
> -	.nbanks		= 4,
> +	.nbanks			= 4,
> +	.last_bank_count	= ATMEL_PIO_NPINS_PER_BANK,
>  };
>  
>  static const struct atmel_pioctrl_data microchip_sama7g5_pioctrl_data = {
> -	.nbanks		= 5,
> +	.nbanks			= 5,
> +	.last_bank_count	= 8, /* sama7g5 has only PE0 to PE7 */
>  };
>  
>  static const struct of_device_id atmel_pctrl_of_match[] = {
> @@ -1025,6 +1034,11 @@ static int atmel_pinctrl_probe(struct platform_device *pdev)
>  	atmel_pioctrl_data = match->data;
>  	atmel_pioctrl->nbanks = atmel_pioctrl_data->nbanks;
>  	atmel_pioctrl->npins = atmel_pioctrl->nbanks * ATMEL_PIO_NPINS_PER_BANK;
> +	/* if last bank has limited number of pins, adjust accordingly */
> +	if (atmel_pioctrl_data->last_bank_count != ATMEL_PIO_NPINS_PER_BANK) {
> +		atmel_pioctrl->npins -= ATMEL_PIO_NPINS_PER_BANK;
> +		atmel_pioctrl->npins += atmel_pioctrl_data->last_bank_count;
> +	}
>  
>  	atmel_pioctrl->reg_base = devm_platform_ioremap_resource(pdev, 0);
>  	if (IS_ERR(atmel_pioctrl->reg_base))
> -- 
> 2.25.1
>