This enables the PEX8311 internal PCI wire interrupt and the PEX8311 local interrupt input so the local interrupts are forwarded to the PCI. Fixes: 585562046628 ("gpio: Add GPIO support for the ACCES PCIe-IDIO-24 family") Signed-off-by: Arnaud de Turckheim <quarium@xxxxxxxxx> --- drivers/gpio/gpio-pcie-idio-24.c | 52 +++++++++++++++++++++++++++++++- 1 file changed, 51 insertions(+), 1 deletion(-) diff --git a/drivers/gpio/gpio-pcie-idio-24.c b/drivers/gpio/gpio-pcie-idio-24.c index a61de14d09b6..2a07fd96707e 100644 --- a/drivers/gpio/gpio-pcie-idio-24.c +++ b/drivers/gpio/gpio-pcie-idio-24.c @@ -28,6 +28,47 @@ #include <linux/spinlock.h> #include <linux/types.h> +/* + * PLX PEX8311 PCI LCS_INTCSR Interrupt Control/Status + * + * Bit: Description + * 0: Enable Interrupt Sources (Bit 0) + * 1: Enable Interrupt Sources (Bit 1) + * 2: Generate Internal PCI Bus Internal SERR# Interrupt + * 3: Mailbox Interrupt Enable + * 4: Power Management Interrupt Enable + * 5: Power Management Interrupt + * 6: Slave Read Local Data Parity Check Error Enable + * 7: Slave Read Local Data Parity Check Error Status + * 8: Internal PCI Wire Interrupt Enable + * 9: PCI Express Doorbell Interrupt Enable + * 10: PCI Abort Interrupt Enable + * 11: Local Interrupt Input Enable + * 12: Retry Abort Enable + * 13: PCI Express Doorbell Interrupt Active + * 14: PCI Abort Interrupt Active + * 15: Local Interrupt Input Active + * 16: Local Interrupt Output Enable + * 17: Local Doorbell Interrupt Enable + * 18: DMA Channel 0 Interrupt Enable + * 19: DMA Channel 1 Interrupt Enable + * 20: Local Doorbell Interrupt Active + * 21: DMA Channel 0 Interrupt Active + * 22: DMA Channel 1 Interrupt Active + * 23: Built-In Self-Test (BIST) Interrupt Active + * 24: Direct Master was the Bus Master during a Master or Target Abort + * 25: DMA Channel 0 was the Bus Master during a Master or Target Abort + * 26: DMA Channel 1 was the Bus Master during a Master or Target Abort + * 27: Target Abort after internal 256 consecutive Master Retrys + * 28: PCI Bus wrote data to LCS_MBOX0 + * 29: PCI Bus wrote data to LCS_MBOX1 + * 30: PCI Bus wrote data to LCS_MBOX2 + * 31: PCI Bus wrote data to LCS_MBOX3 + */ +#define PLX_PEX8311_PCI_LCS_INTCSR 0x68 +#define INTCSR_INTERNAL_PCI_WIRE BIT(8) +#define INTCSR_LOCAL_INPUT BIT(11) + /** * struct idio_24_gpio_reg - GPIO device registers structure * @out0_7: Read: FET Outputs 0-7 @@ -92,6 +133,7 @@ struct idio_24_gpio_reg { struct idio_24_gpio { struct gpio_chip chip; raw_spinlock_t lock; + __u8 __iomem *plx; struct idio_24_gpio_reg __iomem *reg; unsigned long irq_mask; }; @@ -455,6 +497,7 @@ static int idio_24_probe(struct pci_dev *pdev, const struct pci_device_id *id) struct device *const dev = &pdev->dev; struct idio_24_gpio *idio24gpio; int err; + const size_t pci_plx_bar_index = 1; const size_t pci_bar_index = 2; const char *const name = pci_name(pdev); struct gpio_irq_chip *girq; @@ -469,12 +512,13 @@ static int idio_24_probe(struct pci_dev *pdev, const struct pci_device_id *id) return err; } - err = pcim_iomap_regions(pdev, BIT(pci_bar_index), name); + err = pcim_iomap_regions(pdev, BIT(pci_plx_bar_index) | BIT(pci_bar_index), name); if (err) { dev_err(dev, "Unable to map PCI I/O addresses (%d)\n", err); return err; } + idio24gpio->plx = pcim_iomap_table(pdev)[pci_plx_bar_index]; idio24gpio->reg = pcim_iomap_table(pdev)[pci_bar_index]; idio24gpio->chip.label = name; @@ -504,6 +548,12 @@ static int idio_24_probe(struct pci_dev *pdev, const struct pci_device_id *id) /* Software board reset */ iowrite8(0, &idio24gpio->reg->soft_reset); + /* + * enable PLX PEX8311 internal PCI wire interrupt and local interrupt + * input + */ + iowrite8((INTCSR_INTERNAL_PCI_WIRE | INTCSR_LOCAL_INPUT) >> 8, + idio24gpio->plx + PLX_PEX8311_PCI_LCS_INTCSR + 1); err = devm_gpiochip_add_data(dev, &idio24gpio->chip, idio24gpio); if (err) { -- 2.25.1