Re: [PATCH v2 2/2] dt-bindings: pinctrl: qcom: add msm8953 pinctrl bindings

[Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>]

On Wed 07 Oct 11:06 CDT 2020, Vladimir Lypak wrote:

> Add device tree bindings documentation for Qualcomm MSM8953
> pinctrl driver.
> 
> Signed-off-by: Vladimir Lypak <junak.pub@xxxxxxxxx>

Reviewed-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>

Regards,
Bjorn

> ---
> Changes in V2:
>  - removed "wakeup-parent" property.
>  - changed pincfg property pattern to '-pins$' and added its description.
>  - added "serial-pins" subnode to example.
> ---
>  .../pinctrl/qcom,msm8953-pinctrl.yaml         | 167 ++++++++++++++++++
>  1 file changed, 167 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml
> 
> diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml b/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml
> new file mode 100644
> index 000000000000..abe9f4c9b1e3
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/pinctrl/qcom,msm8953-pinctrl.yaml
> @@ -0,0 +1,167 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/pinctrl/qcom,msm8953-pinctrl.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Qualcomm Technologies, Inc. MSM8953 TLMM block
> +
> +maintainers:
> +  - Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
> +
> +description: |
> +  This binding describes the Top Level Mode Multiplexer block found in the
> +  MSM8953 platform.
> +
> +properties:
> +  compatible:
> +    const: qcom,msm8953-pinctrl
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    description: Specifies the TLMM summary IRQ
> +    maxItems: 1
> +
> +  interrupt-controller: true
> +
> +  '#interrupt-cells':
> +    description:
> +      Specifies the PIN numbers and Flags, as defined in defined in
> +      include/dt-bindings/interrupt-controller/irq.h
> +    const: 2
> +
> +  gpio-controller: true
> +
> +  '#gpio-cells':
> +    description: Specifying the pin number and flags, as defined in
> +      include/dt-bindings/gpio/gpio.h
> +    const: 2
> +
> +  gpio-ranges:
> +    maxItems: 1
> +
> +#PIN CONFIGURATION NODES
> +patternProperties:
> +  '-pins$':
> +    type: object
> +    description:
> +      Pinctrl node's client devices use subnodes for desired pin configuration.
> +      Client device subnodes use below standard properties.
> +    $ref: "/schemas/pinctrl/pincfg-node.yaml"
> +
> +    properties:
> +      pins:
> +        description:
> +          List of gpio pins affected by the properties specified in this
> +          subnode.
> +        items:
> +          oneOf:
> +            - pattern: "^gpio([0-9]|[1-9][0-9]|1[0-7][0-9])$"
> +            - enum: [ sdc1_clk, sdc1_cmd, sdc1_data, sdc1_rclk, sdc2_clk,
> +                      sdc2_cmd, sdc2_data, qdsd_clk, qdsd_cmd, qdsd_data0,
> +                      qdsd_data1, qdsd_data2, qdsd_data3 ]
> +        minItems: 1
> +        maxItems: 16
> +
> +      function:
> +        description:
> +          Specify the alternative function to be configured for the specified
> +          pins.
> +
> +        enum: [ accel_int, adsp_ext, alsp_int, atest_bbrx0, atest_bbrx1,
> +                atest_char, atest_char0, atest_char1, atest_char2, atest_char3,
> +                atest_gpsadc_dtest0_native, atest_gpsadc_dtest1_native, atest_tsens,
> +                atest_wlan0, atest_wlan1, bimc_dte0, bimc_dte1, blsp1_spi,
> +                blsp3_spi, blsp6_spi, blsp7_spi, blsp_i2c1, blsp_i2c2, blsp_i2c3,
> +                blsp_i2c4, blsp_i2c5, blsp_i2c6, blsp_i2c7, blsp_i2c8, blsp_spi1,
> +                blsp_spi2, blsp_spi3, blsp_spi4, blsp_spi5, blsp_spi6, blsp_spi7,
> +                blsp_spi8, blsp_uart2, blsp_uart4, blsp_uart5, blsp_uart6, cam0_ldo,
> +                cam1_ldo, cam1_rst, cam1_standby, cam2_rst, cam2_standby, cam3_rst,
> +                cam3_standby, cam_irq, cam_mclk, cap_int, cci_async, cci_i2c,
> +                cci_timer0, cci_timer1, cci_timer2, cci_timer3, cci_timer4,
> +                cdc_pdm0, codec_int1, codec_int2, codec_reset, cri_trng, cri_trng0,
> +                cri_trng1, dac_calib0, dac_calib1, dac_calib10, dac_calib11,
> +                dac_calib12, dac_calib13, dac_calib14, dac_calib15, dac_calib16,
> +                dac_calib17, dac_calib18, dac_calib19, dac_calib2, dac_calib20,
> +                dac_calib21, dac_calib22, dac_calib23, dac_calib24, dac_calib25,
> +                dac_calib3, dac_calib4, dac_calib5, dac_calib6, dac_calib7,
> +                dac_calib8, dac_calib9, dbg_out, ddr_bist, dmic0_clk, dmic0_data,
> +                ebi_cdc, ebi_ch0, ext_lpass, flash_strobe, fp_int, gcc_gp1_clk_a,
> +                gcc_gp1_clk_b, gcc_gp2_clk_a, gcc_gp2_clk_b, gcc_gp3_clk_a,
> +                gcc_gp3_clk_b, gcc_plltest, gcc_tlmm, gpio, gsm0_tx, gsm1_tx,
> +                gyro_int, hall_int, hdmi_int, key_focus, key_home, key_snapshot,
> +                key_volp, ldo_en, ldo_update, lpass_slimbus, lpass_slimbus0,
> +                lpass_slimbus1, m_voc, mag_int, mdp_vsync, mipi_dsi0, modem_tsync,
> +                mss_lte, nav_pps, nav_pps_in_a, nav_pps_in_b, nav_tsync,
> +                nfc_disable, nfc_dwl, nfc_irq, ois_sync, pa_indicator, pbs0, pbs1,
> +                pbs2, pressure_int, pri_mi2s, pri_mi2s_mclk_a, pri_mi2s_mclk_b,
> +                pri_mi2s_ws, prng_rosc, pwr_crypto_enabled_a, pwr_crypto_enabled_b,
> +                pwr_down, pwr_modem_enabled_a, pwr_modem_enabled_b,
> +                pwr_nav_enabled_a, pwr_nav_enabled_b, qdss_cti_trig_in_a0,
> +                qdss_cti_trig_in_a1, qdss_cti_trig_in_b0, qdss_cti_trig_in_b1,
> +                qdss_cti_trig_out_a0, qdss_cti_trig_out_a1, qdss_cti_trig_out_b0,
> +                qdss_cti_trig_out_b1, qdss_traceclk_a, qdss_traceclk_b,
> +                qdss_tracectl_a, qdss_tracectl_b, qdss_tracedata_a,
> +                qdss_tracedata_b, sd_write, sdcard_det, sec_mi2s, sec_mi2s_mclk_a,
> +                sec_mi2s_mclk_b, smb_int, ss_switch, ssbi_wtr1, ts_resout,
> +                ts_sample, ts_xvdd, tsens_max, uim1_clk, uim1_data, uim1_present,
> +                uim1_reset, uim2_clk, uim2_data, uim2_present, uim2_reset,
> +                uim_batt, us_emitter, us_euro, wcss_bt, wcss_fm, wcss_wlan,
> +                wcss_wlan0, wcss_wlan1, wcss_wlan2, wsa_en, wsa_io, wsa_irq ]
> +
> +      drive-strength:
> +        enum: [2, 4, 6, 8, 10, 12, 14, 16]
> +        default: 2
> +        description:
> +          Selects the drive strength for the specified pins, in mA.
> +
> +      bias-pull-down: true
> +
> +      bias-pull-up: true
> +
> +      bias-disable: true
> +
> +      output-high: true
> +
> +      output-low: true
> +
> +    required:
> +      - pins
> +      - function
> +
> +    additionalProperties: false
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - interrupt-controller
> +  - '#interrupt-cells'
> +  - gpio-controller
> +  - '#gpio-cells'
> +  - gpio-ranges
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +        #include <dt-bindings/interrupt-controller/arm-gic.h>
> +        tlmm: pinctrl@1000000 {
> +              compatible = "qcom,msm8953-pinctrl";
> +              reg = <0x01000000 0x300000>;
> +              interrupts = <GIC_SPI 208 IRQ_TYPE_LEVEL_HIGH>;
> +              interrupt-controller;
> +              #interrupt-cells = <2>;
> +              gpio-controller;
> +              #gpio-cells = <2>;
> +              gpio-ranges = <&tlmm 0 0 142>;
> +
> +              serial_default: serial-pins {
> +                    pins = "gpio4", "gpio5";
> +                    function = "blsp_uart2";
> +                    drive-strength = <2>;
> +                    bias-disable;
> +              };
> +        };
> -- 
> 2.28.0
>