Re: [PATCH v8 6/7] arm64: dts: add dts nodes for MT6779

[Hanks Chen <hanks.chen@xxxxxxxxxxxx>]

On Mon, 2020-07-20 at 18:13 +0200, Matthias Brugger wrote:
> 
> On 16/07/2020 06:04, Hanks Chen wrote:
> > On Tue, 2020-07-14 at 20:14 +0200, Matthias Brugger wrote:
> >>
> >> On 14/07/2020 11:20, Hanks Chen wrote:
> >>> this adds initial MT6779 dts settings for board support,
> >>> including cpu, gic, timer, ccf, pinctrl, uart, sysirq...etc.
> >>>
> >>> Signed-off-by: Hanks Chen <hanks.chen@xxxxxxxxxxxx>
> >>> ---
> >>>    arch/arm64/boot/dts/mediatek/Makefile       |   1 +
> >>>    arch/arm64/boot/dts/mediatek/mt6779-evb.dts |  31 +++
> >>>    arch/arm64/boot/dts/mediatek/mt6779.dtsi    | 271 ++++++++++++++++++++
> >>>    3 files changed, 303 insertions(+)
> >>>    create mode 100644 arch/arm64/boot/dts/mediatek/mt6779-evb.dts
> >>>    create mode 100644 arch/arm64/boot/dts/mediatek/mt6779.dtsi
> >>>
> >> [...]
> >>> +
> >>> +		uart0: serial@11002000 {
> >>> +			compatible = "mediatek,mt6779-uart",
> >>> +				     "mediatek,mt6577-uart";
> >>> +			reg = <0 0x11002000 0 0x400>;
> >>> +			interrupts = <GIC_SPI 115 IRQ_TYPE_LEVEL_LOW>;
> >>> +			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_UART0>;
> >>> +			clock-names = "baud", "bus";
> >>> +			status = "disabled";
> >>> +		};
> >>> +
> >>> +		uart1: serial@11003000 {
> >>> +			compatible = "mediatek,mt6779-uart",
> >>> +				     "mediatek,mt6577-uart";
> >>> +			reg = <0 0x11003000 0 0x400>;
> >>> +			interrupts = <GIC_SPI 116 IRQ_TYPE_LEVEL_LOW>;
> >>> +			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_UART1>;
> >>> +			clock-names = "baud", "bus";
> >>> +			status = "disabled";
> >>> +		};
> >>> +
> >>> +		uart2: serial@11004000 {
> >>> +			compatible = "mediatek,mt6779-uart",
> >>> +				     "mediatek,mt6577-uart";
> >>> +			reg = <0 0x11004000 0 0x400>;
> >>> +			interrupts = <GIC_SPI 117 IRQ_TYPE_LEVEL_LOW>;
> >>> +			clocks = <&clk26m>, <&infracfg_ao CLK_INFRA_UART2>;
> >>> +			clock-names = "baud", "bus";
> >>> +			status = "disabled";
> >>> +		};
> >>
> >> Devicetree describes the HW we have. As far as I know, we have 4 UARTs on
> >> MT6779. So we should list them all here.
> >>
> > 
> > Actually, We have only 3 UARTs HW on MT6779, but have 4 UART clk in
> > header file of clk.
> 
> Correct, I got confused by the four clocks.
> With that clarified I'm fine with the patch and will take it as soon as the 
> clock driver patch is accepted.
> 
> Regards,
> Matthias
> 
Got it, I send a new serial to fix the redundant UART clk
https://lkml.org/lkml/2020/7/21/45

Thanks

Hanks Chen

> > CLK_INFRA_UART3 is a dummy clk interface, it has no effect on the
> > operation of the read/write instruction.
> > 
> > If you think it is not good, I can remove it in the header file of clk.
> > 
> > Thanks
> > 
> >> Regards,
> >> Matthias
> >