Re: [PATCH] doc: devicetree: bindings: fix spelling mistake

[Guo Ren <guoren@xxxxxxxxxx>]

Acked-by: Guo Ren <guoren@xxxxxxxxxx>

On Thu, Jun 11, 2020 at 5:58 PM Flavio Suligoi <f.suligoi@xxxxxxx> wrote:
>
> Fix typo: "triger" --> "trigger"
>
> Signed-off-by: Flavio Suligoi <f.suligoi@xxxxxxx>
> ---
>  Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.txt | 2 +-
>  .../devicetree/bindings/interrupt-controller/csky,mpintc.txt    | 2 +-
>  Documentation/devicetree/bindings/timer/csky,mptimer.txt        | 2 +-
>  3 files changed, 3 insertions(+), 3 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.txt b/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.txt
> index ba455589f869..e1c49b660d3a 100644
> --- a/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.txt
> +++ b/Documentation/devicetree/bindings/gpio/mediatek,mt7621-gpio.txt
> @@ -12,7 +12,7 @@ Required properties for the top level node:
>     Only the GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW flags are supported.
>  - #interrupt-cells : Specifies the number of cells needed to encode an
>     interrupt. Should be 2. The first cell defines the interrupt number,
> -   the second encodes the triger flags encoded as described in
> +   the second encodes the trigger flags encoded as described in
>     Documentation/devicetree/bindings/interrupt-controller/interrupts.txt
>  - compatible:
>    - "mediatek,mt7621-gpio" for Mediatek controllers
> diff --git a/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt b/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt
> index e13405355166..e6bbcae4d07f 100644
> --- a/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt
> +++ b/Documentation/devicetree/bindings/interrupt-controller/csky,mpintc.txt
> @@ -10,7 +10,7 @@ Interrupt number definition:
>   16-31  : private  irq, and we use 16 as the co-processor timer.
>   31-1024: common irq for soc ip.
>
> -Interrupt triger mode: (Defined in dt-bindings/interrupt-controller/irq.h)
> +Interrupt trigger mode: (Defined in dt-bindings/interrupt-controller/irq.h)
>   IRQ_TYPE_LEVEL_HIGH (default)
>   IRQ_TYPE_LEVEL_LOW
>   IRQ_TYPE_EDGE_RISING
> diff --git a/Documentation/devicetree/bindings/timer/csky,mptimer.txt b/Documentation/devicetree/bindings/timer/csky,mptimer.txt
> index 15cfec08fbb8..f5c7e99cf52b 100644
> --- a/Documentation/devicetree/bindings/timer/csky,mptimer.txt
> +++ b/Documentation/devicetree/bindings/timer/csky,mptimer.txt
> @@ -8,7 +8,7 @@ regs is accessed by cpu co-processor 4 registers with mtcr/mfcr.
>   - PTIM_CTLR "cr<0, 14>" Control reg to start reset timer.
>   - PTIM_TSR  "cr<1, 14>" Interrupt cleanup status reg.
>   - PTIM_CCVR "cr<3, 14>" Current counter value reg.
> - - PTIM_LVR  "cr<6, 14>" Window value reg to triger next event.
> + - PTIM_LVR  "cr<6, 14>" Window value reg to trigger next event.
>
>  ==============================
>  timer node bindings definition
> --
> 2.17.1
>


-- 
Best Regards
 Guo Ren

ML: https://lore.kernel.org/linux-csky/