Re: [PATCH] dt-bindings: mfd: Convert stmfx bindings to json-schema

[Rob Herring <robh@xxxxxxxxxx>]

On Wed, Jan 29, 2020 at 06:06:13PM +0100, Benjamin Gaignard wrote:
> Convert stmfx bindings to json-schema
> 
> Signed-off-by: Benjamin Gaignard <benjamin.gaignard@xxxxxx>
> ---
>  Documentation/devicetree/bindings/mfd/stmfx.txt    |  28 -----
>  Documentation/devicetree/bindings/mfd/stmfx.yaml   | 100 ++++++++++++++++++
>  .../devicetree/bindings/pinctrl/pinctrl-stmfx.txt  | 116 ---------------------
>  3 files changed, 100 insertions(+), 144 deletions(-)
>  delete mode 100644 Documentation/devicetree/bindings/mfd/stmfx.txt
>  create mode 100644 Documentation/devicetree/bindings/mfd/stmfx.yaml
>  delete mode 100644 Documentation/devicetree/bindings/pinctrl/pinctrl-stmfx.txt
> 
> diff --git a/Documentation/devicetree/bindings/mfd/stmfx.txt b/Documentation/devicetree/bindings/mfd/stmfx.txt
> deleted file mode 100644
> index f0c2f7fcf5c7..000000000000
> --- a/Documentation/devicetree/bindings/mfd/stmfx.txt
> +++ /dev/null
> @@ -1,28 +0,0 @@
> -STMicroelectonics Multi-Function eXpander (STMFX) Core bindings
> -
> -ST Multi-Function eXpander (STMFX) is a slave controller using I2C for
> -communication with the main MCU. Its main features are GPIO expansion, main
> -MCU IDD measurement (IDD is the amount of current that flows through VDD) and
> -resistive touchscreen controller.
> -
> -Required properties:
> -- compatible: should be "st,stmfx-0300".
> -- reg: I2C slave address of the device.
> -- interrupts: interrupt specifier triggered by MFX_IRQ_OUT signal.
> -  Please refer to ../interrupt-controller/interrupt.txt
> -
> -Optional properties:
> -- drive-open-drain: configure MFX_IRQ_OUT as open drain.
> -- vdd-supply: phandle of the regulator supplying STMFX.
> -
> -Example:
> -
> -	stmfx: stmfx@42 {
> -		compatible = "st,stmfx-0300";
> -		reg = <0x42>;
> -		interrupts = <8 IRQ_TYPE_EDGE_RISING>;
> -		interrupt-parent = <&gpioi>;
> -		vdd-supply = <&v3v3>;
> -	};
> -
> -Please refer to ../pinctrl/pinctrl-stmfx.txt for STMFX GPIO expander function bindings.
> diff --git a/Documentation/devicetree/bindings/mfd/stmfx.yaml b/Documentation/devicetree/bindings/mfd/stmfx.yaml
> new file mode 100644
> index 000000000000..4219e0ffcb85
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/stmfx.yaml
> @@ -0,0 +1,100 @@
> +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/mfd/stmfx.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: STMicroelectonics Multi-Function eXpander (STMFX) bindings
> +
> +description: ST Multi-Function eXpander (STMFX) is a slave controller using I2C for
> +             communication with the main MCU. Its main features are GPIO expansion,
> +             main MCU IDD measurement (IDD is the amount of current that flows
> +             through VDD) and resistive touchscreen controller.

Use normal formatting which is 2 spaces.

> +
> +maintainers:
> +  - Amelie Delaunay <amelie.delaunay@xxxxxx>
> +
> +allOf:
> +  - $ref: ../pinctrl/pincfg-node.yaml
> +
> +properties:
> +  compatible:
> +    const: st,stmfx-0300
> +
> +  reg:
> +    enum: [ 0x42, 0x43 ]
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  drive-open-drain: true
> +
> +  vdd-supply:
> +    maxItems: 1
> +
> +  stmfx-pin-controller:

Really should be 'pinctrl'

> +    type: object
> +
> +    properties:
> +      compatible:
> +        const: st,stmfx-0300-pinctrl
> +
> +      "#gpio-cells":
> +        const: 2
> +
> +      "#interrupt-cells":
> +        const: 2
> +
> +      gpio-controller: true
> +
> +      interrupt-controller: true
> +
> +      gpio-ranges:
> +        description: if all STMFX pins[24:0] are available (no other STMFX function in use),
> +                     you should use gpio-ranges = <&stmfx_pinctrl 0 0 24>;
> +                     if agpio[3:0] are not available (STMFX Touchscreen function in use),
> +                     you should use gpio-ranges = <&stmfx_pinctrl 0 0 16>, <&stmfx_pinctrl 20 20 4>;
> +                     if agpio[7:4] are not available (STMFX IDD function in use),
> +                     you should use gpio-ranges = <&stmfx_pinctrl 0 0 20>;
> +        maxItems: 1
> +
> +    required:
> +      - compatible
> +      - "#gpio-cells"
> +      - "#interrupt-cells"
> +      - gpio-controller
> +      - interrupt-controller
> +      - gpio-ranges
> +
> +additionalProperties: false
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    i2c@0 {
> +      #address-cells = <1>;
> +      #size-cells = <0>;
> +      stmfx@42 {
> +        compatible = "st,stmfx-0300";
> +        reg = <0x42>;
> +        interrupts = <8 IRQ_TYPE_EDGE_RISING>;
> +        interrupt-parent = <&gpioi>;
> +        vdd-supply = <&v3v3>;
> +
> +        stmfx-pin-controller {
> +          compatible = "st,stmfx-0300-pinctrl";
> +          #gpio-cells = <2>;
> +          #interrupt-cells = <2>;
> +          gpio-controller;
> +          interrupt-controller;
> +          gpio-ranges = <&stmfx_pinctrl 0 0 24>;

Perhaps keep the label to show this points to this node.

> +        };
> +      };
> +    };
> +
> +...
> diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-stmfx.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-stmfx.txt
> deleted file mode 100644
> index c1b4c1819b84..000000000000
> --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-stmfx.txt
> +++ /dev/null
> @@ -1,116 +0,0 @@
> -STMicroelectronics Multi-Function eXpander (STMFX) GPIO expander bindings
> -
> -ST Multi-Function eXpander (STMFX) offers up to 24 GPIOs expansion.
> -Please refer to ../mfd/stmfx.txt for STMFX Core bindings.
> -
> -Required properties:
> -- compatible: should be "st,stmfx-0300-pinctrl".
> -- #gpio-cells: should be <2>, the first cell is the GPIO number and the second
> -  cell is the gpio flags in accordance with <dt-bindings/gpio/gpio.h>.
> -- gpio-controller: marks the device as a GPIO controller.
> -- #interrupt-cells: should be <2>, the first cell is the GPIO number and the
> -  second cell is the interrupt flags in accordance with
> -  <dt-bindings/interrupt-controller/irq.h>.
> -- interrupt-controller: marks the device as an interrupt controller.
> -- gpio-ranges: specifies the mapping between gpio controller and pin
> -  controller pins. Check "Concerning gpio-ranges property" below.
> -Please refer to ../gpio/gpio.txt.
> -
> -Please refer to pinctrl-bindings.txt for pin configuration.
> -
> -Required properties for pin configuration sub-nodes:
> -- pins: list of pins to which the configuration applies.
> -
> -Optional properties for pin configuration sub-nodes (pinconf-generic ones):
> -- bias-disable: disable any bias on the pin.
> -- bias-pull-up: the pin will be pulled up.
> -- bias-pull-pin-default: use the pin-default pull state.
> -- bias-pull-down: the pin will be pulled down.
> -- drive-open-drain: the pin will be driven with open drain.
> -- drive-push-pull: the pin will be driven actively high and low.
> -- output-high: the pin will be configured as an output driving high level.
> -- output-low: the pin will be configured as an output driving low level.

What about all these nodes?

> -
> -Note that STMFX pins[15:0] are called "gpio[15:0]", and STMFX pins[23:16] are
> -called "agpio[7:0]". Example, to refer to pin 18 of STMFX, use "agpio2".
> -
> -Concerning gpio-ranges property:
> -- if all STMFX pins[24:0] are available (no other STMFX function in use), you
> -  should use gpio-ranges = <&stmfx_pinctrl 0 0 24>;
> -- if agpio[3:0] are not available (STMFX Touchscreen function in use), you
> -  should use gpio-ranges = <&stmfx_pinctrl 0 0 16>, <&stmfx_pinctrl 20 20 4>;
> -- if agpio[7:4] are not available (STMFX IDD function in use), you
> -  should use gpio-ranges = <&stmfx_pinctrl 0 0 20>;
> -
> -
> -Example:
> -
> -	stmfx: stmfx@42 {
> -		...
> -
> -		stmfx_pinctrl: stmfx-pin-controller {
> -			compatible = "st,stmfx-0300-pinctrl";
> -			#gpio-cells = <2>;
> -			#interrupt-cells = <2>;
> -			gpio-controller;
> -			interrupt-controller;
> -			gpio-ranges = <&stmfx_pinctrl 0 0 24>;
> -
> -			joystick_pins: joystick {
> -				pins = "gpio0", "gpio1", "gpio2", "gpio3", "gpio4";
> -				drive-push-pull;
> -				bias-pull-up;
> -			};
> -		};
> -	};
> -
> -Example of STMFX GPIO consumers:
> -
> -	joystick {
> -		compatible = "gpio-keys";
> -		#address-cells = <1>;
> -		#size-cells = <0>;
> -		pinctrl-0 = <&joystick_pins>;
> -		pinctrl-names = "default";
> -		button-0 {
> -			label = "JoySel";
> -			linux,code = <KEY_ENTER>;
> -			interrupt-parent = <&stmfx_pinctrl>;
> -			interrupts = <0 IRQ_TYPE_EDGE_RISING>;
> -		};
> -		button-1 {
> -			label = "JoyDown";
> -			linux,code = <KEY_DOWN>;
> -			interrupt-parent = <&stmfx_pinctrl>;
> -			interrupts = <1 IRQ_TYPE_EDGE_RISING>;
> -		};
> -		button-2 {
> -			label = "JoyLeft";
> -			linux,code = <KEY_LEFT>;
> -			interrupt-parent = <&stmfx_pinctrl>;
> -			interrupts = <2 IRQ_TYPE_EDGE_RISING>;
> -		};
> -		button-3 {
> -			label = "JoyRight";
> -			linux,code = <KEY_RIGHT>;
> -			interrupt-parent = <&stmfx_pinctrl>;
> -			interrupts = <3 IRQ_TYPE_EDGE_RISING>;
> -		};
> -		button-4 {
> -			label = "JoyUp";
> -			linux,code = <KEY_UP>;
> -			interrupt-parent = <&stmfx_pinctrl>;
> -			interrupts = <4 IRQ_TYPE_EDGE_RISING>;
> -		};
> -	};
> -
> -	leds {
> -		compatible = "gpio-leds";
> -		orange {
> -			gpios = <&stmfx_pinctrl 17 1>;
> -		};
> -
> -		blue {
> -			gpios = <&stmfx_pinctrl 19 1>;
> -		};
> -	}
> -- 
> 2.15.0
>