Re: [PATCH v3 3/6] dt-bindings: mfd: da9062: add regulator voltage selection documentation

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Mark,

On 19-12-04 13:46, Mark Brown wrote:
> On Fri, Nov 29, 2019 at 06:25:34PM +0100, Marco Felsch wrote:
> 
> > +  Optional regulator device-specific properties:
> > +  - dlg,vsel-sense-gpios : A GPIO reference to a local general purpose input,
> > +    the datasheet calls it GPI. The regulator sense the input signal and select
> > +    the active or suspend voltage settings. If the signal is active the
> > +    active-settings are applied else the suspend-settings are applied.
> > +    Attention: Sharing the same GPI for other purposes or across multiple
> > +    regulators is possible but the polarity setting must equal.
> 
> I'm really confused by this.  As far as I understand it it seems
> to be doing pinmuxing on the chip using the GPIO bindings which
> is itself a bit odd and I don't see anything here that configures
> whatever sets the state of the pins.  Don't we need another GPIO
> to set the vsel-sense inputs on the PMIC?

Yes the PMIC is very configurable and it took a while till I understand
it.. @Adam please correct me if I'm wrong.

The PMIC regulators regardless of the type: ldo or buck can be
simplified drawn as:



da9062-gpio               da9062-regulator
    
  +-------------------------------------------------------
  |                  PMIC
  |    
  > GPIO0            +--------------------------+
  |                  |         REGULATOR-0      |
  > GPIO1 -------+   |                          |
  |              +-- > vsel-in    voltage-a-out <
  > GPIO2        |   |                          |
  |              |   > enable-in  voltage-b-out <
  |              |   |                          |
  |              |   +--------------------------+
  |              |                              
  |              |   +--------------------------+                          
  |              |   |         REGULATOR-1      |                          
  |              |   |                          |                          
  |              +-- > vsel-in    voltage-a-out <                          
  |                  |                          |                          
  |                  > enable-in  voltage-b-out <
  |                  |                          |
  |                  +--------------------------+
  |

The 'vsel-in' and 'enable-in' regulator inputs must be routed to the
PMIC GPIOs which must be configured as input. If this is a pinmux in
your opinion, then yes we need to do that. IMHO it isn't a pinmux
because from the regulator point of view it is just a GPIO which comes
from our own gpio-dev (da9062-gpio). So the abstraction is vald. Anyway
I'm with you that this isn't the typical use-case.

Regards,
  Marco 

-- 
Pengutronix e.K.                           |                             |
Steuerwalder Str. 21                       | http://www.pengutronix.de/  |
31137 Hildesheim, Germany                  | Phone: +49-5121-206917-0    |
Amtsgericht Hildesheim, HRA 2686           | Fax:   +49-5121-206917-5555 |



[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux