[PATCH v5 3/4] dt-bindings: pinctrl: Add bindings for Ingenic X1830.

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Add the pinctrl bindings for the X1830 Soc from Ingenic.

Signed-off-by: Zhou Yanjie <zhouyanjie@xxxxxxxx>
Acked-by: Rob Herring <robh@xxxxxxxxxx>
---

Notes:
    v2:
    New patch.
    
    v2->v3:
    No change.
    
    v3->v4:
    No change.
    
    v4->v5:
    No change.

 Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt | 8 +++++---
 1 file changed, 5 insertions(+), 3 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt
index 0014d98..d9b2100 100644
--- a/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt
+++ b/Documentation/devicetree/bindings/pinctrl/ingenic,pinctrl.txt
@@ -10,9 +10,9 @@ GPIO port configuration registers and it is typical to refer to pins using the
 naming scheme "PxN" where x is a character identifying the GPIO port with
 which the pin is associated and N is an integer from 0 to 31 identifying the
 pin within that GPIO port. For example PA0 is the first pin in GPIO port A, and
-PB31 is the last pin in GPIO port B. The jz4740 and the x1000 contains 4 GPIO
-ports, PA to PD, for a total of 128 pins. The jz4760, the jz4770 and the jz4780
-contains 6 GPIO ports, PA to PF, for a total of 192 pins.
+PB31 is the last pin in GPIO port B. The jz4740, the x1000 and the x1830
+contains 4 GPIO ports, PA to PD, for a total of 128 pins. The jz4760, the
+jz4770 and the jz4780 contains 6 GPIO ports, PA to PF, for a total of 192 pins.
 
 
 Required properties:
@@ -28,6 +28,7 @@ Required properties:
     - "ingenic,x1000-pinctrl"
     - "ingenic,x1000e-pinctrl"
     - "ingenic,x1500-pinctrl"
+    - "ingenic,x1830-pinctrl"
  - reg: Address range of the pinctrl registers.
 
 
@@ -40,6 +41,7 @@ Required properties for sub-nodes (GPIO chips):
     - "ingenic,jz4770-gpio"
     - "ingenic,jz4780-gpio"
     - "ingenic,x1000-gpio"
+    - "ingenic,x1830-gpio"
  - reg: The GPIO bank number.
  - interrupt-controller: Marks the device node as an interrupt controller.
  - interrupts: Interrupt specifier for the controllers interrupt.
-- 
2.7.4





[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux