Re: [PATCH v5 03/16] dt-bindings: mfd: Document ROHM BD71828 bindings

[Rob Herring <robh@xxxxxxxxxx>]

On Mon, Nov 18, 2019 at 08:54:56AM +0200, Matti Vaittinen wrote:
> ROHM BD71828 Power management IC integrates 7 buck converters, 7 LDOs,
> a real-time clock (RTC), 3 GPO/regulator control pins, HALL input
> and a 32.768 kHz clock gate.
> 
> Document the dt bindings drivers are using.
> 
> Signed-off-by: Matti Vaittinen <matti.vaittinen@xxxxxxxxxxxxxxxxx>
> ---
> 
> No changes from v4
> 
>  .../bindings/mfd/rohm,bd71828-pmic.yaml       | 249 ++++++++++++++++++
>  1 file changed, 249 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml
> 
> diff --git a/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml
> new file mode 100644
> index 000000000000..17ea9fa463e8
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/mfd/rohm,bd71828-pmic.yaml
> @@ -0,0 +1,249 @@
> +# SPDX-License-Identifier: GPL-2.0-only
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/mfd/rohm,bd71828-pmic.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: ROHM BD71828 Power Management Integrated Circuit bindings
> +
> +maintainers:
> +  - Matti Vaittinen <matti.vaittinen@xxxxxxxxxxxxxxxxx>
> +
> +description: |
> +  BD71828GW is a single-chip power management IC for battery-powered portable
> +  devices. The IC integrates 7 buck converters, 7 LDOs, and a 1500 mA
> +  single-cell linear charger. Also included is a Coulomb counter, a real-time
> +  clock (RTC), and a 32.768 kHz clock gate.
> +
> +  The BD71828 RUN state is divided into 4 configurable run-levels named RUN0,
> +  RUN1, RUN2 and RUN3. Bucks 1, 2, 6 and 7 can be either controlled individually
> +  via I2C, or some/all of them can be bound to run-levels and controlled as a
> +  group. If bucks are controlled individually these run-levels are ignored. See
> +  ../regulator/rohm,bd71828-regulator.yaml for how to define regulator voltages
> +  for run-levels. Run-levels can be changed by I2C or GPIO depending on PMIC's
> +  OTP configuration.
> +
> +properties:
> +  compatible:
> +    const: rohm,bd71828
> +
> +  reg:
> +    description:
> +      I2C slave address.
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +    description:
> +      The interrupt line the device is connected to.

The description here is not too useful, I'd drop it.

> +
> +  gpio-controller: true
> +      # Indicate BD71828 acts as a GPIO controller.
> +
> +  "#gpio-cells":
> +    const: 2
> +    description: |
> +      The first cell is the pin number and the second cell is used to specify
> +      flags. See ../gpio/gpio.txt for more information.
> +
> +  clocks:
> +    maxItems: 1
> +    description:
> +      The parent clock connected to PMIC.

The description here is not too useful, I'd drop it.

> +
> +  "#clock-cells":
> +    const: 0
> +
> +  rohm,charger-sense-resistor-ohms:
> +    minimum: 10000000
> +    maximum: 50000000
> +    description: |
> +      BD71827 and BD71828 have SAR ADC for measuring charging currents.
> +      External sense resistor (RSENSE in data sheet) should be used. If some
> +      other but 30MOhm resistor is used the resistance value should be given
> +      here in Ohms.
> +
> +  regulators:
> +    $ref: ../regulator/rohm,bd71828-regulator.yaml
> +    description:
> +      List of child nodes that specify the regulators.
> +
> +  leds:
> +    $ref: ../leds/rohm,bd71828-leds.yaml
> +
> +  rohm,dvs-vsel-gpios:
> +    maxItems: 2
> +    description: |
> +      GPIOs used to control PMIC run-levels. Should describe two GPIOs.
> +      (See run-level control in data-sheet). If this property is omitted but
> +      some bucks are marked to be controlled by run-levels - then OTP option
> +      allowing run-level control via I2C is assumed.
> +
> +  gpio-reserved-ranges:
> +    description: |
> +      Usage of BD71828 GPIO pins can be changed via OTP. This property can be
> +      used to mark the pins which should not be configured for GPIO. Please see
> +      the ../gpio/gpio.txt for more information.
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - clocks
> +  - "#clock-cells"
> +  - regulators
> +  - gpio-controller
> +  - "#gpio-cells"