Re: [PATCH v2 5/6] gpiolib: disable bias on inputs when pull up/down are both set

[Bartosz Golaszewski <brgl@xxxxxxxx>]

czw., 17 paź 2019 o 07:06 Kent Gibson <warthog618@xxxxxxxxx> napisał(a):
>
> On Wed, Oct 16, 2019 at 09:01:04AM +0800, Kent Gibson wrote:
> > On Tue, Oct 15, 2019 at 02:51:18PM +0200, Bartosz Golaszewski wrote:
> > > wt., 15 paź 2019 o 02:58 Kent Gibson <warthog618@xxxxxxxxx> napisał(a):
> > > >
> > > > On Mon, Oct 14, 2019 at 06:50:41PM +0200, Bartosz Golaszewski wrote:
> > > > > pon., 14 paź 2019 o 15:04 Kent Gibson <warthog618@xxxxxxxxx> napisał(a):
> > > > > >
> > > > > > On Mon, Oct 14, 2019 at 02:43:54PM +0200, Bartosz Golaszewski wrote:
> > > > > > > sob., 12 paź 2019 o 03:57 Kent Gibson <warthog618@xxxxxxxxx> napisał(a):
> > > > > > > >
> > > > > > > > This patch allows pull up/down bias to be disabled, allowing
> > > > > > > > the line to float or to be biased only by external circuitry.
> > > > > > > > Use case is for where the bias has been applied previously,
> > > > > > > > either by default or by the user, but that setting may
> > > > > > > > conflict with the current use of the line.
> > > > > > > >
> > > > > > > > Signed-off-by: Kent Gibson <warthog618@xxxxxxxxx>
> > > > > > > > ---
> > > > > > > >  drivers/gpio/gpiolib.c | 22 +++++++---------------
> > > > > > > >  1 file changed, 7 insertions(+), 15 deletions(-)
> > > > > > > >
> > > > > > > > diff --git a/drivers/gpio/gpiolib.c b/drivers/gpio/gpiolib.c
> > > > > > > > index 647334f53622..f90b20d548b9 100644
> > > > > > > > --- a/drivers/gpio/gpiolib.c
> > > > > > > > +++ b/drivers/gpio/gpiolib.c
> > > > > > > > @@ -539,11 +539,6 @@ static int linehandle_create(struct gpio_device *gdev, void __user *ip)
> > > > > > > >             (lflags & GPIOHANDLE_REQUEST_OUTPUT))
> > > > > > > >                 return -EINVAL;
> > > > > > > >
> > > > > > > > -       /* Same with pull-up and pull-down. */
> > > > > > > > -       if ((lflags & GPIOHANDLE_REQUEST_PULL_UP) &&
> > > > > > > > -           (lflags & GPIOHANDLE_REQUEST_PULL_DOWN))
> > > > > > > > -               return -EINVAL;
> > > > > > > > -
> > > > > > > >         /*
> > > > > > > >          * Do not allow OPEN_SOURCE & OPEN_DRAIN flags in a single request. If
> > > > > > > >          * the hardware actually supports enabling both at the same time the
> > > > > > > > @@ -935,14 +930,6 @@ static int lineevent_create(struct gpio_device *gdev, void __user *ip)
> > > > > > > >              (lflags & GPIOHANDLE_REQUEST_PULL_DOWN)))
> > > > > > > >                 return -EINVAL;
> > > > > > > >
> > > > > > > > -       /*
> > > > > > > > -        * Do not allow both pull-up and pull-down flags to be set as they
> > > > > > > > -        *  are contradictory.
> > > > > > > > -        */
> > > > > > > > -       if ((lflags & GPIOHANDLE_REQUEST_PULL_UP) &&
> > > > > > > > -           (lflags & GPIOHANDLE_REQUEST_PULL_DOWN))
> > > > > > > > -               return -EINVAL;
> > > > > > > > -
> > > > > > > >         le = kzalloc(sizeof(*le), GFP_KERNEL);
> > > > > > > >         if (!le)
> > > > > > > >                 return -ENOMEM;
> > > > > > > > @@ -2931,6 +2918,7 @@ static int gpio_set_config(struct gpio_chip *gc, unsigned offset,
> > > > > > > >         unsigned arg;
> > > > > > > >
> > > > > > > >         switch (mode) {
> > > > > > > > +       case PIN_CONFIG_BIAS_DISABLE:
> > > > > > > >         case PIN_CONFIG_BIAS_PULL_DOWN:
> > > > > > > >         case PIN_CONFIG_BIAS_PULL_UP:
> > > > > > > >                 arg = 1;
> > > > > > > > @@ -2991,7 +2979,11 @@ int gpiod_direction_input(struct gpio_desc *desc)
> > > > > > > >         if (ret == 0)
> > > > > > > >                 clear_bit(FLAG_IS_OUT, &desc->flags);
> > > > > > > >
> > > > > > > > -       if (test_bit(FLAG_PULL_UP, &desc->flags))
> > > > > > > > +       if (test_bit(FLAG_PULL_UP, &desc->flags) &&
> > > > > > > > +               test_bit(FLAG_PULL_DOWN, &desc->flags))
> > > > > > > > +               gpio_set_config(chip, gpio_chip_hwgpio(desc),
> > > > > > > > +                               PIN_CONFIG_BIAS_DISABLE);
> > > > > > > > +       else if (test_bit(FLAG_PULL_UP, &desc->flags))
> > > > > > >
> > > > > > > From looking at the code: user-space can disable bias when setting
> > > > > > > both PULL_UP and PULL_DOWN flags. I don't understand why it's done in
> > > > > > > this implicit way? Why not a separate flag?
> > > > > >
> > > > > > An extra flag would waste a bit and add nothing but more sanity checking.
> > > > > >
> > > > >
> > > > > I disagree. The user API needs to be very explicit. Sanity checking is
> > > > > alright - if there'll be too many ifdefs, we can start thinking about
> > > > > adding some core library helpers for sanitizing conflicting flags, I'm
> > > > > sure other frameworks could use something like this as well.
> > > > >
> > > > > Especially in this context: setting PULL_UP and PULL_DOWN together
> > > > > disables bias - this doesn't make sense logically.
> > > > >
> > > > In a way it does make a weird kind of sense - they cancel.  Physically.
> > > >
> > >
> > > Yes, on some devices we set both bits to disable bias, but on others
> > > the pull-up and pull-down bits need to be cleared and yet others have
> > > a dedicated bit for that. It's not standardized and the pinctrl
> > > framework defines all three values as separate bits to expose a common
> > > programming interface.
> > >
>
> Is there any documentation on this?  The pinctrl docs stay pretty high
> level and doesn't touch on this. And from the pinconf-generic.h
> documentation, I'd consider drivers that require both pull-up and
> pull-down set to disable bias to be non-compliant with the API - for
> BIAS_DISABLE it says "this setting disables all biasing", so you'd think
> the driver would support that and do any mapping (setting both pulls
> high or low or whatever) internally.
>
> > Ok. And, since gpiolib has no knowledge of what combinations are
> > appropriate for a given chip, we can't provide a higher level
> > abstraction and have no option but to expose that pinconf
> > complexity in the GPIO uapi?
> >
> > In fact, pinconf doesn't just define 3 bias bits - it defines 6:
> >
> > enum pin_config_param {
> >       PIN_CONFIG_BIAS_BUS_HOLD,
> >       PIN_CONFIG_BIAS_DISABLE,
> >       PIN_CONFIG_BIAS_HIGH_IMPEDANCE,
> >       PIN_CONFIG_BIAS_PULL_DOWN,
> >       PIN_CONFIG_BIAS_PULL_PIN_DEFAULT,
> >       PIN_CONFIG_BIAS_PULL_UP,
> >
> > Do we need to support any of the remaining 3 in the GPIO uapi, either
> > now or possibly in the future?
> >
> > And what about the other PIN_CONFIG flags?  Some of these might be
> > candidates for controlling via SET_CONFIG_IOCTL, if not in the request
> > itself? (again this is contemplating the future, not suggesting being part
> > of this patch)
> >
> > > > Did you read the cover letter?  The problem, as I see it,
> > > > is that we're stuck using a flag field to encode a two bit enum.
> > > > That fact the we only have a flag field to play with can't be
> > > > changed due to ABI.
> > >
> > > For some reason I haven't received the cover letter on my inbox. I'm
> > > only now seeing it on linux-gpio archives.
> > >
> > And for some reason I didn't get 0001, yet all 7 parts made it to the mailing
> > list. Spam filters kicking in? Though it isn't in my spam folder either.
> > Something odd going on.
> >
> > > Anyway: I don't understand why you insist on using two instead of
> > > three bits. You have 32 bits in total that can be used and only 5 are
> > > used so far. There's plenty left.
> > >
> > Cos it makes no sense to me to encode 4 values into 3 bits when 2 will
> > do.  But if you want to expose part of the pinconf API within the GPIO
> > uapi then that goes out the window - it's not 4 values anymore.
> >
> > And partly cos I'm frustrated that I'd asked questions regarding how the
> > API should look earlier and got no reply.  This is the sort of thing I
> > usually deal with in the design stage, not review.
> >
> > I realise you guys are busy, but a little time spent clarifying design
> > would save a whole lot more time in coding, testing and review.
> >
> > > I'd prefer to see:
> > >
> > > GPIOHANDLE_REQUEST_PULL_UP
> > > GPIOHANDLE_REQUEST_PULL_DOWN
> > > GPIOHANDLE_REQUEST_PULL_DISABLED
> > >
> > > or maybe even
> > >
> > > GPIOHANDLE_REQUEST_BIAS_PULL_UP
> > > GPIOHANDLE_REQUEST_BIAS_PULL_DOWN
> > > GPIOHANDLE_REQUEST_BIAS_DISABLED
> > >
> > > to stay consistent with the pinctrl flags. No bit set among these
> > > three would mean AS_IS.
> > >
> > That makes sense, if we are exposing the pinctrl API here.
> >
>
> Looking at going with the naming including BIAS...
> What to do with constants defined in headers prior to this patch that
> don't include the BIAS?  e.g. FLAG_PULL_UP and FLAG_PULL_DOWN in gpiolib.h?

But this has nothing to do with user-space. This was added so that
GPIO expanders can use this without pulling in the pinctrl framework.

> Safe to assume they can't be renamed?

What for?

> So ok to stay with the unBIASed names for both old (cos they are there)
> and also the new (to be consistent with the old)?

There's no need for perfect naming consistency between user and kernel
space declarations. The difference is: you need to be sure to get the
user-space flags right the first time - unlike the kernel APIs, they
cannot be renamed later.

>
> Also, while the DT interface (gpiod_configure_flags) has GPIO_PULL_UP
> and GPIO_PULL_DOWN, it doesn't support DISABLE, and it explicitly rejects
> both having both PULL_UP and PULL_DOWN set.  Should we be extending the
> DISABLE support to the DT interface, and should the API behaviour also
> mirror the pinctrl behaviour you describe above?

Is someone needing it? Adding new features without users is frowned
upon for good reasons.

>
> And are there any combinations that are guaranteed to be invalid,
> and so should be rejected, like DISABLE + PULL_UP??  In fact are there
> any combinations that are valid other then PULL_UP + PULL_DOWN?

You mean invalid? You just said PULL_UP + PULL_DOWN is rejected.

Bart

>
> Cheers,
> Kent.