czw., 17 paź 2019 o 11:53 Matti Vaittinen
<matti.vaittinen@xxxxxxxxxxxxxxxxx> napisał(a):
>
> ROHM BD71828 PMIC contains 4 pins which can be configured by OTP
> to be used for general purposes. First 3 can be used as outputs
> and 4.th pin can be used as input. Allow them to be controlled
> via GPIO framework.
>
> The driver assumes all of the pins are configured as GPIOs and
> rusts that the reserved pins in other OTP configurations are
> excluded from control using "gpio-reserved-ranges" device tree
> property (or left untouched by GPIO users).
>
> Typical use for 4.th pin (input) is to use it as HALL sensor
> input so that this pin state is toggled when HALL sensor detects
> LID position change (from close to open or open to close). PMIC
> HW implements some extra logic which allows PMIC to power-up the
> system when this pin is toggled. Please see the data sheet for
> details of GPIO options which can be selcted by OTP settings.
>
> Signed-off-by: Matti Vaittinen <matti.vaittinen@xxxxxxxxxxxxxxxxx>
> ---
> drivers/gpio/Kconfig | 12 +++
> drivers/gpio/Makefile | 1 +
> drivers/gpio/gpio-bd71828.c | 161 ++++++++++++++++++++++++++++++++++++
> 3 files changed, 174 insertions(+)
> create mode 100644 drivers/gpio/gpio-bd71828.c
>
> diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
> index bb13c266c329..fb0a099de961 100644
> --- a/drivers/gpio/Kconfig
> +++ b/drivers/gpio/Kconfig
> @@ -986,6 +986,18 @@ config GPIO_BD70528
> This driver can also be built as a module. If so, the module
> will be called gpio-bd70528.
>
> +config GPIO_BD71828
> + tristate "ROHM BD71828 GPIO support"
> + depends on MFD_ROHM_BD71828
> + help
> + Support for GPIOs on ROHM BD71828 PMIC. There are three GPIOs
> + available on the ROHM PMIC in total. The GPIOs are limited to
> + outputs only and pins must be configured to GPIO outputs by
> + OTP. Enable this only if you want to use these pins as outputs.
> +
> + This driver can also be built as a module. If so, the module
> + will be called gpio-bd71828.
> +
> config GPIO_BD9571MWV
> tristate "ROHM BD9571 GPIO support"
> depends on MFD_BD9571MWV
> diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile
> index a4e91175c708..b11932844768 100644
> --- a/drivers/gpio/Makefile
> +++ b/drivers/gpio/Makefile
> @@ -35,6 +35,7 @@ obj-$(CONFIG_GPIO_ASPEED) += gpio-aspeed.o
> obj-$(CONFIG_GPIO_ATH79) += gpio-ath79.o
> obj-$(CONFIG_GPIO_BCM_KONA) += gpio-bcm-kona.o
> obj-$(CONFIG_GPIO_BD70528) += gpio-bd70528.o
> +obj-$(CONFIG_GPIO_BD71828) += gpio-bd71828.o
> obj-$(CONFIG_GPIO_BD9571MWV) += gpio-bd9571mwv.o
> obj-$(CONFIG_GPIO_BRCMSTB) += gpio-brcmstb.o
> obj-$(CONFIG_GPIO_BT8XX) += gpio-bt8xx.o
> diff --git a/drivers/gpio/gpio-bd71828.c b/drivers/gpio/gpio-bd71828.c
> new file mode 100644
> index 000000000000..3cf3890a24c4
> --- /dev/null
> +++ b/drivers/gpio/gpio-bd71828.c
> @@ -0,0 +1,161 @@
> +// SPDX-License-Identifier: GPL-2.0
> +// Copyright (C) 2018 ROHM Semiconductors
> +// gpio-bd71828.c ROHM BD71828 gpio driver
I don't think the name of the source file is needed here.
> +
> +#include <linux/gpio/driver.h>
> +#include <linux/mfd/rohm-bd71828.h>
> +#include <linux/module.h>
> +#include <linux/platform_device.h>
> +#include <linux/regmap.h>
> +
> +#define OUT 0
> +#define IN 1
If you really want to define those, please use a common prefix for all
symbols in the driver.
> +#define GPIO_OUT_REG(off) (BD71828_REG_GPIO_CTRL1 + (off))
> +#define HALL_GPIO_OFFSET 3
> +
> +struct bd71828_gpio {
> + struct rohm_regmap_dev chip;
> + struct gpio_chip gpio;
> +};
> +
> +static void bd71828_gpio_set(struct gpio_chip *chip, unsigned int offset,
> + int value)
> +{
> + int ret;
> + struct bd71828_gpio *bdgpio = gpiochip_get_data(chip);
> + u8 val = (value) ? BD71828_GPIO_OUT_HI : BD71828_GPIO_OUT_LO;
> +
> + if (offset == HALL_GPIO_OFFSET)
> + return;
Can you add a comment here saying that this pin can only be used as
input? Otherwise this information is only available in the commit
message.
> +
> + ret = regmap_update_bits(bdgpio->chip.regmap, GPIO_OUT_REG(offset),
> + BD71828_GPIO_OUT_MASK, val);
> + if (ret)
> + dev_err(bdgpio->chip.dev, "Could not set gpio to %d\n", value);
> +}
> +
> +static int bd71828_gpio_get(struct gpio_chip *chip, unsigned int offset)
> +{
> + int ret;
> + unsigned int val;
> + struct bd71828_gpio *bdgpio = gpiochip_get_data(chip);
> +
> + if (offset == HALL_GPIO_OFFSET)
> + ret = regmap_read(bdgpio->chip.regmap, BD71828_REG_IO_STAT,
> + &val);
> + else
> + ret = regmap_read(bdgpio->chip.regmap, GPIO_OUT_REG(offset),
> + &val);
> + if (!ret)
> + ret = (val & BD71828_GPIO_OUT_MASK);
> +
> + return ret;
> +}
> +
> +static int bd71828_gpio_set_config(struct gpio_chip *chip, unsigned int offset,
> + unsigned long config)
> +{
> + struct bd71828_gpio *bdgpio = gpiochip_get_data(chip);
> +
> + if (offset == HALL_GPIO_OFFSET)
> + return -ENOTSUPP;
> +
> + switch (pinconf_to_config_param(config)) {
> + case PIN_CONFIG_DRIVE_OPEN_DRAIN:
> + return regmap_update_bits(bdgpio->chip.regmap,
> + GPIO_OUT_REG(offset),
> + BD71828_GPIO_DRIVE_MASK,
> + BD71828_GPIO_OPEN_DRAIN);
> + case PIN_CONFIG_DRIVE_PUSH_PULL:
> + return regmap_update_bits(bdgpio->chip.regmap,
> + GPIO_OUT_REG(offset),
> + BD71828_GPIO_DRIVE_MASK,
> + BD71828_GPIO_PUSH_PULL);
> + default:
> + break;
> + }
> + return -ENOTSUPP;
> +}
> +
> +static int bd71828_get_direction(struct gpio_chip *chip, unsigned int offset)
> +{
> + /*
> + * Pin usage is selected by OTP data. We can't read it runtime. Hence
> + * we trust that if the pin is not excluded by "gpio-reserved-ranges"
> + * the OTP configuration is set to OUT. (Other pins but HALL input pin
> + * on BD71828 can't really be used for general purpose input - input
> + * states are used for specific cases like regulator control or
> + * PMIC_ON_REQ.
> + */
> + if (offset == HALL_GPIO_OFFSET)
> + return IN;
> +
> + return OUT;
> +}
> +
> +static int bd71828_gpio_parse_dt(struct device *dev,
> + struct bd71828_gpio *bdgpio)
> +{
> + /*
> + * TBD: See if we need some implementation to mark some PINs as
> + * not controllable based on DT info or if core can handle
> + * "gpio-reserved-ranges" and exclude them from control
> + */
> + return 0;
> +}
Please don't implement empty functions. Just add this comment next to
gpiochip's initialization...
> +
> +static int bd71828_probe(struct platform_device *pdev)
> +{
> + struct bd71828_gpio *bdgpio;
> + struct rohm_regmap_dev *bd71828;
> + int ret;
> +
> + bd71828 = dev_get_drvdata(pdev->dev.parent);
> + if (!bd71828) {
> + dev_err(&pdev->dev, "No MFD driver data\n");
> + return -EINVAL;
> + }
> +
> + bdgpio = devm_kzalloc(&pdev->dev, sizeof(*bdgpio),
> + GFP_KERNEL);
> + if (!bdgpio)
> + return -ENOMEM;
> +
> + ret = bd71828_gpio_parse_dt(pdev->dev.parent, bdgpio);
... and remove this call.
> +
> + bdgpio->chip.dev = &pdev->dev;
> + bdgpio->gpio.parent = pdev->dev.parent;
> + bdgpio->gpio.label = "bd71828-gpio";
> + bdgpio->gpio.owner = THIS_MODULE;
> + bdgpio->gpio.get_direction = bd71828_get_direction;
> + bdgpio->gpio.set_config = bd71828_gpio_set_config;
> + bdgpio->gpio.can_sleep = true;
> + bdgpio->gpio.get = bd71828_gpio_get;
> + bdgpio->gpio.set = bd71828_gpio_set;
Not implementing direction_output() and direction_input() here will
results in warnings from the GPIO framework: for instance you
implement set() but not direction_output(). I'd say: just add those
callbacks and return an error if they're called for invalid lines (for
instance: direction_output() being called for line 3).
> + bdgpio->gpio.base = -1;
> + bdgpio->gpio.ngpio = 4;
> +#ifdef CONFIG_OF_GPIO
This is not needed - for CONFIG_OF_GPIO disabled the parent of_node
will be NULL.
> + bdgpio->gpio.of_node = pdev->dev.parent->of_node;
> +#endif
> + bdgpio->chip.regmap = bd71828->regmap;
> +
> + ret = devm_gpiochip_add_data(&pdev->dev, &bdgpio->gpio,
> + bdgpio);
> + if (ret)
> + dev_err(&pdev->dev, "gpio_init: Failed to add bd71828-gpio\n");
Since there aren't many places where this function can fail, you can
directly return devm_gpiochip_add_data() here.
> +
> + return ret;
> +}
> +
> +static struct platform_driver bd71828_gpio = {
> + .driver = {
> + .name = "bd71828-gpio"
> + },
> + .probe = bd71828_probe,
> +};
> +
> +module_platform_driver(bd71828_gpio);
> +
> +MODULE_AUTHOR("Matti Vaittinen <matti.vaittinen@xxxxxxxxxxxxxxxxx>");
> +MODULE_DESCRIPTION("BD71828 voltage regulator driver");
> +MODULE_LICENSE("GPL");
Don't you need a MODULE_ALIAS() here since this is an MFD sub-module?
Bart
> --
> 2.21.0
>
>
> --
> Matti Vaittinen, Linux device drivers
> ROHM Semiconductors, Finland SWDC
> Kiviharjunlenkki 1E
> 90220 OULU
> FINLAND
>
> ~~~ "I don't think so," said Rene Descartes. Just then he vanished ~~~
> Simon says - in Latin please.
> ~~~ "non cogito me" dixit Rene Descarte, deinde evanescavit ~~~
> Thanks to Simon Glass for the translation =]
Re: [RFC PATCH 10/13] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
- Subject: Re: [RFC PATCH 10/13] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs
- From: Bartosz Golaszewski <bgolaszewski@xxxxxxxxxxxx>
- Date: Thu, 17 Oct 2019 14:45:06 +0200
- In-reply-to: <f8f8c323d378244afe4e94f48c0a94bb296cbbe0.1571302099.git.matti.vaittinen@fi.rohmeurope.com>
- References: <cover.1571302099.git.matti.vaittinen@fi.rohmeurope.com> <f8f8c323d378244afe4e94f48c0a94bb296cbbe0.1571302099.git.matti.vaittinen@fi.rohmeurope.com>
- Follow-Ups:
- Re: [RFC PATCH 10/13] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs
- From: Vaittinen, Matti
- Re: [RFC PATCH 10/13] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs
- References:
- [RFC PATCH 00/13] Support ROHM BD71828 PMIC
- From: Matti Vaittinen
- [RFC PATCH 10/13] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs
- From: Matti Vaittinen
- [RFC PATCH 00/13] Support ROHM BD71828 PMIC
- Prev by Date: drivers/pinctrl/sh-pfc/pfc-sh7734.c multiple define of TCLK1_B
- Next by Date: [PATCH -next 01/30] pinctrl: pxa25x: use devm_platform_ioremap_resource() to simplify code
- Previous by thread: [RFC PATCH 10/13] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs
- Next by thread: Re: [RFC PATCH 10/13] gpio: bd71828: Initial support for ROHM BD71828 PMIC GPIOs
- Index(es):
 |