[PATCH v1] pinctrl: intel: Avoid potential glitches if pin is in GPIO mode

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



When consumer requests a pin, in order to be on the safest side,
we switch it first to GPIO mode followed by immediate transition
to the input state. Due to posted writes it's luckily to be a single
I/O transaction.

However, if firmware or boot loader already configures the pin
to the GPIO mode, user expects no glitches for the requested pin.
We may check if the pin is pre-configured and leave it as is
till the actual consumer toggles its state to avoid glitches.

Fixes: 7981c0015af2 ("pinctrl: intel: Add Intel Sunrisepoint pin controller and GPIO support")
Depends-on: f5a26acf0162 ("pinctrl: intel: Initialize GPIO properly when used through irqchip")
Cc: fei.yang@xxxxxxxxx
Reported-by: Oliver Barta <oliver.barta@xxxxxxxxx>
Reported-by: Malin Jonsson <malin.jonsson@xxxxxxxxxxxx>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@xxxxxxxxxxxxxxx>
---
 drivers/pinctrl/intel/pinctrl-intel.c | 21 ++++++++++++++++++++-
 1 file changed, 20 insertions(+), 1 deletion(-)

diff --git a/drivers/pinctrl/intel/pinctrl-intel.c b/drivers/pinctrl/intel/pinctrl-intel.c
index b9df243e19cf..df8ca7cdefcb 100644
--- a/drivers/pinctrl/intel/pinctrl-intel.c
+++ b/drivers/pinctrl/intel/pinctrl-intel.c
@@ -52,6 +52,7 @@
 #define PADCFG0_GPIROUTNMI		BIT(17)
 #define PADCFG0_PMODE_SHIFT		10
 #define PADCFG0_PMODE_MASK		GENMASK(13, 10)
+#define PADCFG0_PMODE_GPIO		0
 #define PADCFG0_GPIORXDIS		BIT(9)
 #define PADCFG0_GPIOTXDIS		BIT(8)
 #define PADCFG0_GPIORXSTATE		BIT(1)
@@ -332,7 +333,7 @@ static void intel_pin_dbg_show(struct pinctrl_dev *pctldev, struct seq_file *s,
 	cfg1 = readl(intel_get_padcfg(pctrl, pin, PADCFG1));
 
 	mode = (cfg0 & PADCFG0_PMODE_MASK) >> PADCFG0_PMODE_SHIFT;
-	if (!mode)
+	if (mode == PADCFG0_PMODE_GPIO)
 		seq_puts(s, "GPIO ");
 	else
 		seq_printf(s, "mode %d ", mode);
@@ -458,6 +459,11 @@ static void __intel_gpio_set_direction(void __iomem *padcfg0, bool input)
 	writel(value, padcfg0);
 }
 
+static int intel_gpio_get_gpio_mode(void __iomem *padcfg0)
+{
+	return (readl(padcfg0) & PADCFG0_PMODE_MASK) >> PADCFG0_PMODE_SHIFT;
+}
+
 static void intel_gpio_set_gpio_mode(void __iomem *padcfg0)
 {
 	u32 value;
@@ -491,7 +497,20 @@ static int intel_gpio_request_enable(struct pinctrl_dev *pctldev,
 	}
 
 	padcfg0 = intel_get_padcfg(pctrl, pin, PADCFG0);
+
+	/*
+	 * If pin is already configured in GPIO mode, we assume that
+	 * firmware provides correct settings. In such case we avoid
+	 * potential glitches on the pin. Otherwise, for the pin in
+	 * alternative mode, consumer has to supply respective flags.
+	 */
+	if (intel_gpio_get_gpio_mode(padcfg0) == PADCFG0_PMODE_GPIO) {
+		raw_spin_unlock_irqrestore(&pctrl->lock, flags);
+		return 0;
+	}
+
 	intel_gpio_set_gpio_mode(padcfg0);
+
 	/* Disable TX buffer and enable RX (this will be input) */
 	__intel_gpio_set_direction(padcfg0, true);
 
-- 
2.23.0




[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux