Re: [PATCH 3/3] arm64: dts: qcom: sdm845-mtp: Specify UFS device-reset GPIO

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue 04 Jun 09:22 PDT 2019, Stephen Boyd wrote:

> Quoting Bjorn Andersson (2019-06-04 00:20:01)
> > Specify the UFS device-reset gpio, so that the controller will issue a
> > reset of the UFS device.
> > 
> > Signed-off-by: Bjorn Andersson <bjorn.andersson@xxxxxxxxxx>
> > ---
> >  arch/arm64/boot/dts/qcom/sdm845-mtp.dts | 2 ++
> >  1 file changed, 2 insertions(+)
> > 
> > diff --git a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> > index 2e78638eb73b..d116a0956a9c 100644
> > --- a/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> > +++ b/arch/arm64/boot/dts/qcom/sdm845-mtp.dts
> > @@ -388,6 +388,8 @@
> >  &ufs_mem_hc {
> >         status = "okay";
> >  
> > +       device-reset-gpios = <&tlmm 150 GPIO_ACTIVE_LOW>;
> > +
> 
> We had to do something similar on one particular brand of UFS that we had. I
> think it was an SK Hynix part that had trouble and wouldn't provision properly.
> Either way, we did this with a pinctrl toggle in the DTS where the "init" state
> has the UFS_RESET pin asserted and then "default" state has the pin deasserted.
> That was good enough to make this work.
> 

Thanks for pointing this out, I forgot to attribute these downstream
changes. I can see how this works, but I must say I find it quite
hackish.

The downstream solution seems to have evolved this into naming these
states and jumping between them (with the appropriate sleeps) during a
host reset as well.


But thanks for the confirmation that there's more than John's memory
that needs this.

Regards,
Bjorn

> 	&ufs_mem_hc {
> 		pinctrl-names = "init", "default";
> 		pinctrl-0 = <&ufs_dev_reset_assert>;
> 		pinctrl-1 = <&ufs_dev_reset_deassert>;
> 	};
> 
>         ufs_dev_reset_assert: ufs_dev_reset_assert {
>                 config {
>                         pins = "ufs_reset";
>                         bias-pull-down;         /* default: pull down */
>                         drive-strength = <8>;   /* default: 3.1 mA */
>                         output-low; /* active low reset */
>                 };
>         };
> 
>         ufs_dev_reset_deassert: ufs_dev_reset_deassert {
>                 config {
>                         pins = "ufs_reset";
>                         bias-pull-down;         /* default: pull down */
>                         drive-strength = <8>;
>                         output-high; /* active low reset */
>                 };
>         };



[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux