Re: [PATCH 07/12] arm64: dts: allwinner: orange-pi-3: Enable ethernet

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Sat, Apr 06, 2019 at 01:45:09AM +0200, megous@xxxxxxxxxx wrote:
> From: Ondrej Jirman <megous@xxxxxxxxxx>
>
> Orange Pi 3 has two regulators that power the Realtek RTL8211E.
> According to the phy datasheet, both regulators need to be enabled
> at the same time, but we can only specify a single phy-supply in
> the DT.
>
> This can be achieved by making one regulator depedning on the
> other via vin-supply. While it's not a technically correct
> description of the hardware, it achieves the purpose.
>
> All values of RX/TX delay were tested exhaustively and a middle
> one of the working values was chosen.
>
> Signed-off-by: Ondrej Jirman <megous@xxxxxxxxxx>
> ---
>  .../dts/allwinner/sun50i-h6-orangepi-3.dts    | 44 +++++++++++++++++++
>  1 file changed, 44 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> index 644946749088..5270142527f5 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h6-orangepi-3.dts
> @@ -15,6 +15,7 @@
>
>  	aliases {
>  		serial0 = &uart0;
> +		ethernet0 = &emac;
>  	};
>
>  	chosen {
> @@ -64,6 +65,27 @@
>  		regulator-max-microvolt = <5000000>;
>  		regulator-always-on;
>  	};
> +
> +	/*
> +	 * The board uses 2.5V RGMII signalling. Power sequence
> +	 * to enable the phy is to enable GMAC-2V5 and GMAC-3V3 (aldo2)
> +	 * power rails at the same time and to wait 100ms.
> +	 */
> +	reg_gmac_2v5: gmac-2v5 {
> +                compatible = "regulator-fixed";
> +                regulator-name = "gmac-2v5";
> +                regulator-min-microvolt = <2500000>;
> +                regulator-max-microvolt = <2500000>;
> +                startup-delay-us = <100000>;
> +                enable-active-high;
> +                gpio = <&pio 3 6 GPIO_ACTIVE_HIGH>; /* PD6 */

Is enable-active-high still needed? It's redundant with the
GPIO_ACTIVE_HIGH flag.

The indentation is wrong here as well.

Maxime

--
Maxime Ripard, Bootlin
Embedded Linux and Kernel engineering
https://bootlin.com

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux