[PATCH 14/14] ARM: dts: sun8i: s3l: add support for Pine64 Single Cube Computer

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



The Single Cube Computer kit by Pine64 is a development kit with
Allwinner S3L SoC.

It comes with a main board, an expansion board and a camera.

The main board features a Micro-USB power-only jack, a USB Type-A port,
an Ethernet port connected to the internal PHY of the SoC. A RGB LED
port is reserved on the board.

The expansion board features a TF slot, a microphone and a speaker
connector with on-board amplifier.

Add support for the kit, with features on the main board and the
expansion board now.

Signed-off-by: Icenowy Zheng <icenowy@xxxxxxx>
---
 arch/arm/boot/dts/Makefile                    |   1 +
 .../dts/sun8i-s3l-single-cube-computer.dts    | 166 ++++++++++++++++++
 2 files changed, 167 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun8i-s3l-single-cube-computer.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index f4f5aeaf3298..a77d1a000953 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1096,6 +1096,7 @@ dtb-$(CONFIG_MACH_SUN8I) += \
 	sun8i-r16-nintendo-super-nes-classic.dtb \
 	sun8i-r16-parrot.dtb \
 	sun8i-r40-bananapi-m2-ultra.dtb \
+	sun8i-s3l-single-cube-computer.dtb \
 	sun8i-t3-cqa3t-bv3.dtb \
 	sun8i-v3s-licheepi-zero.dtb \
 	sun8i-v3s-licheepi-zero-dock.dtb \
diff --git a/arch/arm/boot/dts/sun8i-s3l-single-cube-computer.dts b/arch/arm/boot/dts/sun8i-s3l-single-cube-computer.dts
new file mode 100644
index 000000000000..a014de597c8a
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-s3l-single-cube-computer.dts
@@ -0,0 +1,166 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR X11)
+/*
+ * Copyright 2019 Icenowy Zheng <icenowy@xxxxxxx>
+ */
+
+/dts-v1/;
+#include "sun8i-s3l.dtsi"
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+	model = "Pine64 Single Cube Computer";
+	compatible = "pine64,single-cube-computer", "allwinner,sun8i-s3l";
+
+	aliases {
+		serial0 = &uart2;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+
+		led1 {
+			label = "pine64:green:led1";
+			gpios = <&pio 1 11 GPIO_ACTIVE_LOW>; /* PB11 */
+		};
+
+		led2 {
+			label = "pine64:green:led2";
+			gpios = <&pio 1 10 GPIO_ACTIVE_LOW>; /* PB10 */
+		};
+
+		led3 {
+			label = "pine64:green:led3";
+			gpios = <&pio 1 12 GPIO_ACTIVE_LOW>; /* PB12 */
+		};
+
+		led4 {
+			label = "pine64:green:led4";
+			gpios = <&pio 1 13 GPIO_ACTIVE_LOW>; /* PB13 */
+		};
+	};
+
+	reg_vcc5v0: vcc5v0 {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc5v0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+	};
+
+	reg_vcc_wifi: vcc-wifi {
+		compatible = "regulator-fixed";
+		regulator-name = "vcc-wifi";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+		gpio = <&pio 1 2 GPIO_ACTIVE_LOW>; /* PB2 WIFI-EN */
+		vin-supply = <&reg_dcdc3>;
+		startup-delay-us = <200000>;
+	};
+
+	wifi_pwrseq: wifi_pwrseq {
+		compatible = "mmc-pwrseq-simple";
+		reset-gpios = <&pio 1 3 GPIO_ACTIVE_LOW>; /* PB3 WIFI-RST */
+		post-power-on-delay-ms = <200>;
+	};
+};
+
+&emac {
+	phy-handle = <&int_mii_phy>;
+	phy-mode = "mii";
+	status = "okay";
+};
+
+&i2c0 {
+	status = "okay";
+
+	axp209: pmic@34 {
+		compatible = "x-powers,axp203",
+			     "x-powers,axp209";
+		reg = <0x34>;
+		interrupt-parent = <&gic>;
+		interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+	};
+};
+
+&mmc0 {
+	vmmc-supply = <&reg_dcdc3>;
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_LOW>;
+	status = "okay";
+};
+
+&mmc1 {
+	vmmc-supply = <&reg_vcc_wifi>;
+	vqmmc-supply = <&reg_dcdc3>;
+	mmc-pwrseq = <&wifi_pwrseq>;
+	bus-width = <4>;
+	non-removable;
+	status = "okay";
+};
+
+&pio {
+	vcc-pd-supply = <&reg_dcdc3>;
+	vcc-pe-supply = <&reg_ldo3>;
+};
+
+#include "axp209.dtsi"
+
+&ac_power_supply {
+	status = "okay";
+};
+
+&reg_dcdc2 {
+	regulator-always-on;
+	regulator-min-microvolt = <1250000>;
+	regulator-max-microvolt = <1250000>;
+	regulator-name = "vdd-sys-cpu-ephy";
+};
+
+&reg_dcdc3 {
+	regulator-always-on;
+	regulator-min-microvolt = <3300000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "vcc-3v3";
+};
+
+&reg_ldo1 {
+	regulator-name = "vdd-rtc";
+};
+
+&reg_ldo2 {
+	regulator-always-on;
+	regulator-min-microvolt = <3000000>;
+	regulator-max-microvolt = <3000000>;
+	regulator-name = "avcc";
+};
+
+&reg_ldo3 {
+	regulator-min-microvolt = <2800000>;
+	regulator-max-microvolt = <2800000>;
+	regulator-name = "vcc-pe";
+};
+
+&reg_ldo4 {
+	regulator-min-microvolt = <1800000>;
+	regulator-max-microvolt = <3300000>;
+	regulator-name = "avdd-mipi";
+};
+
+&uart2 {
+	status = "okay";
+};
+
+&usb_otg {
+	dr_mode = "host";
+	status = "okay";
+};
+
+&usbphy {
+	usb0_vbus-supply = <&reg_vcc5v0>;
+	status = "okay";
+};
-- 
2.18.1




[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux