Re: [PATCH v3 11/11] dt-bindings: gpio: Add bindings for Cadence I3C gpio expander

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Geert,

On Mon, 26 Mar 2018 12:17:26 +0200
Geert Uytterhoeven <geert@xxxxxxxxxxxxxx> wrote:

> Hi Boris,
> 
> On Fri, Mar 23, 2018 at 12:00 PM, Boris Brezillon
> <boris.brezillon@xxxxxxxxxxx> wrote:
> > Document the Cadence I3C gpio expander bindings.
> >
> > Signed-off-by: Boris Brezillon <boris.brezillon@xxxxxxxxxxx>  
> 
> Thanks for your patch!
> 
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/gpio/gpio-cdns-i3c.txt
> > @@ -0,0 +1,38 @@
> > +* Cadence I3C GPIO expander
> > +
> > +The Cadence I3C GPIO expander provides 8 GPIOs controllable over I3C.
> > +This GPIOs can be configured in output or input mode and if they are in input
> > +mode they can generate IBIs (In Band Interrupts).
> > +
> > +Required properties for GPIO node:
> > +- reg : 3 cells encoding the I3C static address (none in our case) and the I3C
> > +       Provisional ID. See Documentation/devicetree/bindings/i3c/i3c.txt for
> > +       more details.
> > +       Should be <0x0 0x392 0x0>.  
> 
> No compatible value?

See my other reply.

> 
> > +- gpio-controller : Marks the device node as a gpio controller.
> > +- #gpio-cells : Should be two. The first cell is the pin number and
> > +  the second cell is used to specify the gpio polarity:
> > +      0 = active high
> > +      1 = active low
> > +- interrupt-controller: Marks the device node as an interrupt controller.
> > +- #interrupt-cells : Should be 2.  The first cell is the GPIO number.
> > +  The second cell bits[3:0] is used to specify trigger type and level flags:
> > +      1 = low-to-high edge triggered.
> > +      2 = high-to-low edge triggered.
> > +      3 = triggered on both edges.
> > +      4 = active high level-sensitive.
> > +      8 = active low level-sensitive.
> > +
> > +Example:
> > +
> > +       i3c-master@xxx {
> > +               ...
> > +               i3c_gpio_expander: gpio@0,1c9,0 {  
> 
> gpio@0,392,0?

Actually, if I follow the DT bindings, it should be gpio@0,39200000000

Thanks,

Boris

-- 
Boris Brezillon, Bootlin (formerly Free Electrons)
Embedded Linux and Kernel engineering
https://bootlin.com
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux