On 09/10/2017 12:17, Jerome Brunet wrote: > When meson pinctrl is enabled, all meson platforms pinctrl drivers are > built in the kernel, with a significant amount of data. > > This leads to situation where pinctrl drivers targeting an architecture > are also compiled and shipped on another one (ex: meson8 - ARM - compiled > and shipped on ARM64 builds). This is a waste of memory we can easily > avoid. > > This change makes 4 pinctrl drivers (1 per SoC) out the original single > driver, allowing to compile and ship only the ones required. > > Signed-off-by: Jerome Brunet <jbrunet@xxxxxxxxxxxx> > --- > drivers/pinctrl/Kconfig | 11 +------ > drivers/pinctrl/meson/Kconfig | 36 +++++++++++++++++++++ > drivers/pinctrl/meson/Makefile | 8 +++-- > drivers/pinctrl/meson/pinctrl-meson-gxbb.c | 25 +++++++++++++-- > drivers/pinctrl/meson/pinctrl-meson-gxl.c | 25 +++++++++++++-- > drivers/pinctrl/meson/pinctrl-meson.c | 51 ++---------------------------- > drivers/pinctrl/meson/pinctrl-meson.h | 11 ++----- > drivers/pinctrl/meson/pinctrl-meson8.c | 25 +++++++++++++-- > drivers/pinctrl/meson/pinctrl-meson8b.c | 25 +++++++++++++-- > 9 files changed, 140 insertions(+), 77 deletions(-) > create mode 100644 drivers/pinctrl/meson/Kconfig > > diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig > index 1778cf4f81c7..15b5b3b76ba9 100644 > --- a/drivers/pinctrl/Kconfig > +++ b/drivers/pinctrl/Kconfig > @@ -167,16 +167,6 @@ config PINCTRL_MCP23S08 > This provides a GPIO interface supporting inputs and outputs. > The I2C versions of the chips can be used as interrupt-controller. > > -config PINCTRL_MESON > - bool > - depends on OF > - select PINMUX > - select PINCONF > - select GENERIC_PINCONF > - select GPIOLIB > - select OF_GPIO > - select REGMAP_MMIO > - > config PINCTRL_OXNAS > bool > depends on OF > @@ -368,6 +358,7 @@ source "drivers/pinctrl/uniphier/Kconfig" > source "drivers/pinctrl/vt8500/Kconfig" > source "drivers/pinctrl/mediatek/Kconfig" > source "drivers/pinctrl/zte/Kconfig" > +source "drivers/pinctrl/meson/Kconfig" > > config PINCTRL_XWAY > bool > diff --git a/drivers/pinctrl/meson/Kconfig b/drivers/pinctrl/meson/Kconfig > new file mode 100644 > index 000000000000..15655bfd39b6 > --- /dev/null > +++ b/drivers/pinctrl/meson/Kconfig > @@ -0,0 +1,36 @@ > +menuconfig PINCTRL_MESON > + bool "Amlogic SoC pinctrl drivers" > + depends on ARCH_MESON || COMPILE_TEST > + depends on OF > + select PINMUX > + select PINCONF > + select GENERIC_PINCONF > + select GPIOLIB > + select OF_GPIO > + select REGMAP_MMIO > + select PINMUX > + select GENERIC_PINCONF > + > +if PINCTRL_MESON > + > +config PINCTRL_MESON8 > + bool "Meson 8 SoC pinctrl driver" > + depends on ARM > + default y > + > +config PINCTRL_MESON8B > + bool "Meson 8b SoC pinctrl driver" > + depends on ARM > + default y > + > +config PINCTRL_MESON_GXBB > + bool "Meson gxbb SoC pinctrl driver" > + depends on ARM64 > + default y > + > +config PINCTRL_MESON_GXL > + bool "Meson gxl SoC pinctrl driver" > + depends on ARM64 > + default y > + > +endif > diff --git a/drivers/pinctrl/meson/Makefile b/drivers/pinctrl/meson/Makefile > index 27c5b5126008..a6ef5ff4e9b1 100644 > --- a/drivers/pinctrl/meson/Makefile > +++ b/drivers/pinctrl/meson/Makefile > @@ -1,3 +1,5 @@ > -obj-y += pinctrl-meson8.o pinctrl-meson8b.o > -obj-y += pinctrl-meson-gxbb.o pinctrl-meson-gxl.o > -obj-y += pinctrl-meson.o > +obj-y += pinctrl-meson.o > +obj-$(CONFIG_PINCTRL_MESON8) += pinctrl-meson8.o > +obj-$(CONFIG_PINCTRL_MESON8B) += pinctrl-meson8b.o > +obj-$(CONFIG_PINCTRL_MESON_GXBB) += pinctrl-meson-gxbb.o > +obj-$(CONFIG_PINCTRL_MESON_GXL) += pinctrl-meson-gxl.o > diff --git a/drivers/pinctrl/meson/pinctrl-meson-gxbb.c b/drivers/pinctrl/meson/pinctrl-meson-gxbb.c > index 1881d4a0eca2..a87bdb17414b 100644 > --- a/drivers/pinctrl/meson/pinctrl-meson-gxbb.c > +++ b/drivers/pinctrl/meson/pinctrl-meson-gxbb.c > @@ -824,7 +824,7 @@ static struct meson_bank meson_gxbb_aobus_banks[] = { > BANK("AO", GPIOAO_0, GPIOAO_13, 0, 13, 0, 0, 0, 16, 0, 0, 0, 16, 1, 0), > }; > > -struct meson_pinctrl_data meson_gxbb_periphs_pinctrl_data = { > +static struct meson_pinctrl_data meson_gxbb_periphs_pinctrl_data = { > .name = "periphs-banks", > .pins = meson_gxbb_periphs_pins, > .groups = meson_gxbb_periphs_groups, > @@ -836,7 +836,7 @@ struct meson_pinctrl_data meson_gxbb_periphs_pinctrl_data = { > .num_banks = ARRAY_SIZE(meson_gxbb_periphs_banks), > }; > > -struct meson_pinctrl_data meson_gxbb_aobus_pinctrl_data = { > +static struct meson_pinctrl_data meson_gxbb_aobus_pinctrl_data = { > .name = "aobus-banks", > .pins = meson_gxbb_aobus_pins, > .groups = meson_gxbb_aobus_groups, > @@ -847,3 +847,24 @@ struct meson_pinctrl_data meson_gxbb_aobus_pinctrl_data = { > .num_funcs = ARRAY_SIZE(meson_gxbb_aobus_functions), > .num_banks = ARRAY_SIZE(meson_gxbb_aobus_banks), > }; > + > +static const struct of_device_id meson_gxbb_pinctrl_dt_match[] = { > + { > + .compatible = "amlogic,meson-gxbb-periphs-pinctrl", > + .data = &meson_gxbb_periphs_pinctrl_data, > + }, > + { > + .compatible = "amlogic,meson-gxbb-aobus-pinctrl", > + .data = &meson_gxbb_aobus_pinctrl_data, > + }, > + { }, > +}; > + > +static struct platform_driver meson_gxbb_pinctrl_driver = { > + .probe = meson_pinctrl_probe, > + .driver = { > + .name = "meson-gxbb-pinctrl", > + .of_match_table = meson_gxbb_pinctrl_dt_match, > + }, > +}; > +builtin_platform_driver(meson_gxbb_pinctrl_driver); > diff --git a/drivers/pinctrl/meson/pinctrl-meson-gxl.c b/drivers/pinctrl/meson/pinctrl-meson-gxl.c > index 3a14ecae9f31..088ac94f76b0 100644 > --- a/drivers/pinctrl/meson/pinctrl-meson-gxl.c > +++ b/drivers/pinctrl/meson/pinctrl-meson-gxl.c > @@ -809,7 +809,7 @@ static struct meson_bank meson_gxl_aobus_banks[] = { > BANK("AO", GPIOAO_0, GPIOAO_9, 0, 9, 0, 0, 0, 16, 0, 0, 0, 16, 1, 0), > }; > > -struct meson_pinctrl_data meson_gxl_periphs_pinctrl_data = { > +static struct meson_pinctrl_data meson_gxl_periphs_pinctrl_data = { > .name = "periphs-banks", > .pins = meson_gxl_periphs_pins, > .groups = meson_gxl_periphs_groups, > @@ -821,7 +821,7 @@ struct meson_pinctrl_data meson_gxl_periphs_pinctrl_data = { > .num_banks = ARRAY_SIZE(meson_gxl_periphs_banks), > }; > > -struct meson_pinctrl_data meson_gxl_aobus_pinctrl_data = { > +static struct meson_pinctrl_data meson_gxl_aobus_pinctrl_data = { > .name = "aobus-banks", > .pins = meson_gxl_aobus_pins, > .groups = meson_gxl_aobus_groups, > @@ -832,3 +832,24 @@ struct meson_pinctrl_data meson_gxl_aobus_pinctrl_data = { > .num_funcs = ARRAY_SIZE(meson_gxl_aobus_functions), > .num_banks = ARRAY_SIZE(meson_gxl_aobus_banks), > }; > + > +static const struct of_device_id meson_gxl_pinctrl_dt_match[] = { > + { > + .compatible = "amlogic,meson-gxl-periphs-pinctrl", > + .data = &meson_gxl_periphs_pinctrl_data, > + }, > + { > + .compatible = "amlogic,meson-gxl-aobus-pinctrl", > + .data = &meson_gxl_aobus_pinctrl_data, > + }, > + { }, > +}; > + > +static struct platform_driver meson_gxl_pinctrl_driver = { > + .probe = meson_pinctrl_probe, > + .driver = { > + .name = "meson-gxl-pinctrl", > + .of_match_table = meson_gxl_pinctrl_dt_match, > + }, > +}; > +builtin_platform_driver(meson_gxl_pinctrl_driver); > diff --git a/drivers/pinctrl/meson/pinctrl-meson.c b/drivers/pinctrl/meson/pinctrl-meson.c > index 71bccb7acbf8..8fc1f1b45435 100644 > --- a/drivers/pinctrl/meson/pinctrl-meson.c > +++ b/drivers/pinctrl/meson/pinctrl-meson.c > @@ -481,42 +481,6 @@ static int meson_gpio_get(struct gpio_chip *chip, unsigned gpio) > return !!(val & BIT(bit)); > } > > -static const struct of_device_id meson_pinctrl_dt_match[] = { > - { > - .compatible = "amlogic,meson8-cbus-pinctrl", > - .data = &meson8_cbus_pinctrl_data, > - }, > - { > - .compatible = "amlogic,meson8b-cbus-pinctrl", > - .data = &meson8b_cbus_pinctrl_data, > - }, > - { > - .compatible = "amlogic,meson8-aobus-pinctrl", > - .data = &meson8_aobus_pinctrl_data, > - }, > - { > - .compatible = "amlogic,meson8b-aobus-pinctrl", > - .data = &meson8b_aobus_pinctrl_data, > - }, > - { > - .compatible = "amlogic,meson-gxbb-periphs-pinctrl", > - .data = &meson_gxbb_periphs_pinctrl_data, > - }, > - { > - .compatible = "amlogic,meson-gxbb-aobus-pinctrl", > - .data = &meson_gxbb_aobus_pinctrl_data, > - }, > - { > - .compatible = "amlogic,meson-gxl-periphs-pinctrl", > - .data = &meson_gxl_periphs_pinctrl_data, > - }, > - { > - .compatible = "amlogic,meson-gxl-aobus-pinctrl", > - .data = &meson_gxl_aobus_pinctrl_data, > - }, > - { }, > -}; > - > static int meson_gpiolib_register(struct meson_pinctrl *pc) > { > int ret; > @@ -624,7 +588,7 @@ static int meson_pinctrl_parse_dt(struct meson_pinctrl *pc, > return 0; > } > > -static int meson_pinctrl_probe(struct platform_device *pdev) > +int meson_pinctrl_probe(struct platform_device *pdev) > { > const struct of_device_id *match; > struct device *dev = &pdev->dev; > @@ -636,10 +600,10 @@ static int meson_pinctrl_probe(struct platform_device *pdev) > return -ENOMEM; > > pc->dev = dev; > - match = of_match_node(meson_pinctrl_dt_match, pdev->dev.of_node); > + match = of_match_node(dev->driver->of_match_table, dev->of_node); Minor comment, maybe you could use of_device_get_match_data(dev) here, it will be simpler. > pc->data = (struct meson_pinctrl_data *) match->data; > > - ret = meson_pinctrl_parse_dt(pc, pdev->dev.of_node); > + ret = meson_pinctrl_parse_dt(pc, dev->of_node); > if (ret) > return ret; > > @@ -659,12 +623,3 @@ static int meson_pinctrl_probe(struct platform_device *pdev) > > return meson_gpiolib_register(pc); > } > - > -static struct platform_driver meson_pinctrl_driver = { > - .probe = meson_pinctrl_probe, > - .driver = { > - .name = "meson-pinctrl", > - .of_match_table = meson_pinctrl_dt_match, > - }, > -}; > -builtin_platform_driver(meson_pinctrl_driver); > diff --git a/drivers/pinctrl/meson/pinctrl-meson.h b/drivers/pinctrl/meson/pinctrl-meson.h > index 7ed0a80fd9dc..284157d43612 100644 > --- a/drivers/pinctrl/meson/pinctrl-meson.h > +++ b/drivers/pinctrl/meson/pinctrl-meson.h > @@ -13,6 +13,7 @@ > > #include <linux/gpio.h> > #include <linux/pinctrl/pinctrl.h> > +#include <linux/platform_device.h> > #include <linux/regmap.h> > #include <linux/types.h> > > @@ -165,11 +166,5 @@ struct meson_pinctrl { > > #define MESON_PIN(x) PINCTRL_PIN(x, #x) > > -extern struct meson_pinctrl_data meson8_cbus_pinctrl_data; > -extern struct meson_pinctrl_data meson8_aobus_pinctrl_data; > -extern struct meson_pinctrl_data meson8b_cbus_pinctrl_data; > -extern struct meson_pinctrl_data meson8b_aobus_pinctrl_data; > -extern struct meson_pinctrl_data meson_gxbb_periphs_pinctrl_data; > -extern struct meson_pinctrl_data meson_gxbb_aobus_pinctrl_data; > -extern struct meson_pinctrl_data meson_gxl_periphs_pinctrl_data; > -extern struct meson_pinctrl_data meson_gxl_aobus_pinctrl_data; > +/* Common probe function */ > +int meson_pinctrl_probe(struct platform_device *pdev); > diff --git a/drivers/pinctrl/meson/pinctrl-meson8.c b/drivers/pinctrl/meson/pinctrl-meson8.c > index fbf8ecd1c2b6..68b345fc105a 100644 > --- a/drivers/pinctrl/meson/pinctrl-meson8.c > +++ b/drivers/pinctrl/meson/pinctrl-meson8.c > @@ -1044,7 +1044,7 @@ static struct meson_bank meson8_aobus_banks[] = { > BANK("AO", GPIOAO_0, GPIO_TEST_N, 0, 13, 0, 0, 0, 16, 0, 0, 0, 16, 1, 0), > }; > > -struct meson_pinctrl_data meson8_cbus_pinctrl_data = { > +static struct meson_pinctrl_data meson8_cbus_pinctrl_data = { > .name = "cbus-banks", > .pins = meson8_cbus_pins, > .groups = meson8_cbus_groups, > @@ -1056,7 +1056,7 @@ struct meson_pinctrl_data meson8_cbus_pinctrl_data = { > .num_banks = ARRAY_SIZE(meson8_cbus_banks), > }; > > -struct meson_pinctrl_data meson8_aobus_pinctrl_data = { > +static struct meson_pinctrl_data meson8_aobus_pinctrl_data = { > .name = "ao-bank", > .pins = meson8_aobus_pins, > .groups = meson8_aobus_groups, > @@ -1067,3 +1067,24 @@ struct meson_pinctrl_data meson8_aobus_pinctrl_data = { > .num_funcs = ARRAY_SIZE(meson8_aobus_functions), > .num_banks = ARRAY_SIZE(meson8_aobus_banks), > }; > + > +static const struct of_device_id meson8_pinctrl_dt_match[] = { > + { > + .compatible = "amlogic,meson8-cbus-pinctrl", > + .data = &meson8_cbus_pinctrl_data, > + }, > + { > + .compatible = "amlogic,meson8-aobus-pinctrl", > + .data = &meson8_aobus_pinctrl_data, > + }, > + { }, > +}; > + > +static struct platform_driver meson8_pinctrl_driver = { > + .probe = meson_pinctrl_probe, > + .driver = { > + .name = "meson8-pinctrl", > + .of_match_table = meson8_pinctrl_dt_match, > + }, > +}; > +builtin_platform_driver(meson8_pinctrl_driver); > diff --git a/drivers/pinctrl/meson/pinctrl-meson8b.c b/drivers/pinctrl/meson/pinctrl-meson8b.c > index 7af296db48c8..4d61df09bc3f 100644 > --- a/drivers/pinctrl/meson/pinctrl-meson8b.c > +++ b/drivers/pinctrl/meson/pinctrl-meson8b.c > @@ -904,7 +904,7 @@ static struct meson_bank meson8b_aobus_banks[] = { > BANK("AO", GPIOAO_0, GPIO_TEST_N, 0, 13, 0, 0, 0, 16, 0, 0, 0, 16, 1, 0), > }; > > -struct meson_pinctrl_data meson8b_cbus_pinctrl_data = { > +static struct meson_pinctrl_data meson8b_cbus_pinctrl_data = { > .name = "cbus-banks", > .pins = meson8b_cbus_pins, > .groups = meson8b_cbus_groups, > @@ -916,7 +916,7 @@ struct meson_pinctrl_data meson8b_cbus_pinctrl_data = { > .num_banks = ARRAY_SIZE(meson8b_cbus_banks), > }; > > -struct meson_pinctrl_data meson8b_aobus_pinctrl_data = { > +static struct meson_pinctrl_data meson8b_aobus_pinctrl_data = { > .name = "aobus-banks", > .pins = meson8b_aobus_pins, > .groups = meson8b_aobus_groups, > @@ -927,3 +927,24 @@ struct meson_pinctrl_data meson8b_aobus_pinctrl_data = { > .num_funcs = ARRAY_SIZE(meson8b_aobus_functions), > .num_banks = ARRAY_SIZE(meson8b_aobus_banks), > }; > + > +static const struct of_device_id meson8b_pinctrl_dt_match[] = { > + { > + .compatible = "amlogic,meson8b-cbus-pinctrl", > + .data = &meson8b_cbus_pinctrl_data, > + }, > + { > + .compatible = "amlogic,meson8b-aobus-pinctrl", > + .data = &meson8b_aobus_pinctrl_data, > + }, > + { }, > +}; > + > +static struct platform_driver meson8b_pinctrl_driver = { > + .probe = meson_pinctrl_probe, > + .driver = { > + .name = "meson8b-pinctrl", > + .of_match_table = meson8b_pinctrl_dt_match, > + }, > +}; > +builtin_platform_driver(meson8b_pinctrl_driver); > Apart the comment on of_device_get_match_data() : Reviewed-by: Neil Armstrong <narmstrong@xxxxxxxxxxxx> -- To unsubscribe from this list: send the line "unsubscribe linux-gpio" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html