Re: [PATCH v7 2/9] dt-bindings: add Amlogic Meson GPIO interrupt-controller DT binding documentation

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 10/06/17 22:57, Heiner Kallweit wrote:
> Add dt binding documentation for Amlogic meson GPIO interrupt controller.
> 
> Signed-off-by: Heiner Kallweit <hkallweit1@xxxxxxxxx>
> Reviewed-by: Neil Armstrong <narmstrong@xxxxxxxxxxxx>
> Acked-by: Rob Herring <robh@xxxxxxxxxx>
> ---
> v5:
> - added Reviewed-by
> v6:
> - rename parent-interrupts to interrupts
> v7:
> - no changes
> ---
>  .../amlogic,meson-gpio-intc.txt                    | 26 ++++++++++++++++++++++
>  1 file changed, 26 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt
> 
> diff --git a/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt
> new file mode 100644
> index 00000000..4c9bb323
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/interrupt-controller/amlogic,meson-gpio-intc.txt
> @@ -0,0 +1,26 @@
> +Amlogic meson GPIO interrupt controller
> +
> +Meson SoCs contains an interrupt controller which is able watch the SoC pads
> +and generate an interrupt on edges or level. The controller is essentially a
> +256 pads to 8 GIC interrupt multiplexer, with a filter block to select edge
> +or level and polarity. The actual number of interrupt exposed depends on the
> +SoC.
> +
> +Required properties:
> +
> +- compatible : should be "amlogic,meson-gpio-intc".
> +- reg : Specifies base physical address and size of the registers.
> +- interrupt-controller : Identifies the node as an interrupt controller.
> +- #interrupt-cells : should be 2.
> +- interrupts : list of GIC interrupts which can be used with the
> +	       GPIO IRQ multiplexer
> +
> +Example:
> +
> +gpio_intc: interrupt-controller@9880 {
> +	compatible = "amlogic,meson-gpio-intc";
> +	reg = <0x0 0x09880 0x0 0x10>;
> +	interrupt-controller;
> +	#interrupt-cells = <2>;
> +	interrupts = <64 65 66 67 68 69 70 71>;

What does it mean to have single-cell interrupt specifiers like this,
when the interrupt-parent is a GIC, which has #interrupt-cells set to 3?
Either you use actual interrupt specifiers, or you use another identifier.

Thanks,

	M.
-- 
Jazz is not dead. It just smells funny...
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux