[PATCH v2 03/18] dt-bindings: mfd: Add bindings for Cirrus Logic Madera codecs

[Richard Fitzgerald <rf@xxxxxxxxxxxxxxxxxxxxxxxxxxx>]

Specification of the bindings for the parent MFD driver component
of the Cirrus Logic Madera codec drivers.

Signed-off-by: Richard Fitzgerald <rf@xxxxxxxxxxxxxxxxxxxxxxxxxxx>
---
Changes since V1:
- split out from main MFD patch
- moved interrupt control binding descriptions into here
- added description of the regulator child nodes
- fixed the node name of the example
- removed the MICBIAS from the example, these have been removed from the code

 Documentation/devicetree/bindings/mfd/madera.txt | 96 ++++++++++++++++++++++++
 1 file changed, 96 insertions(+)
 create mode 100644 Documentation/devicetree/bindings/mfd/madera.txt

diff --git a/Documentation/devicetree/bindings/mfd/madera.txt b/Documentation/devicetree/bindings/mfd/madera.txt
new file mode 100644
index 0000000..af9b85f
--- /dev/null
+++ b/Documentation/devicetree/bindings/mfd/madera.txt
@@ -0,0 +1,96 @@
+Cirrus Logic Madera class audio codecs multi-function device
+
+These devices are audio SoCs with extensive digital capabilities and a range
+of analogue I/O.
+
+See also the child driver bindings in:
+bindings/gpio/gpio-madera.txt
+bindings/pinctrl/cirrus,madera-pinctrl.txt
+bindings/regulator/arizona-regulator.txt
+bindings/sound/madera.txt
+
+Required properties:
+
+  - compatible : One of the following chip-specific strings:
+        "cirrus,cs47l35"
+        "cirrus,cs47l85"
+        "cirrus,cs47l90"
+        "cirrus,cs47l91"
+        "cirrus,wm1840"
+
+  - reg : I2C slave address when connected using I2C, chip select number when
+    using SPI.
+
+  - DCVDD-supply : Power supply for the device as defined in
+    bindings/regulator/regulator.txt
+    Mandatory on CS47L35, CS47L90, CS47L91
+    Optional on CS47L85, WM1840
+
+  - AVDD-supply, DBVDD1-supply, DBVDD2-supply, CPVDD1-supply, CPVDD2-supply :
+    Power supplies for the device
+
+  - DBVDD3-supply, DBVDD4-supply : Power supplies for the device
+    (CS47L85, CS47L90, CS47L91, WM1840)
+
+  - SPKVDDL-supply, SPKVDDR-supply : Power supplies for the device
+    (CS47L85, WM1840)
+
+  - SPKVDD-supply : Power supply for the device
+    (CS47L35)
+
+  - interrupt-controller : Madera class devices contain interrupt controllers
+    and may provide interrupt services to other devices.
+
+  - #interrupt-cells: the number of cells to describe an IRQ, must be 2.
+    The first cell is the IRQ number.
+    The second cell is the flags, encoded as the trigger masks from
+    bindings/interrupt-controller/interrupts.txt
+
+  - interrupt-parent : The parent interrupt controller.
+
+  - interrupts : The interrupt line the /IRQ signal for the device is
+    connected to.
+
+Optional properties:
+
+  - MICVDD-supply : Power supply, only need to be specified if
+    powered externally
+
+  - reset-gpios : One entry specifying the GPIO controlling /RESET.
+    As defined in bindings/gpio.txt.
+    Although optional, it is strongly recommended to use a hardware reset
+
+  - MICBIASx : Initial data for the MICBIAS regulators, as covered in
+    Documentation/devicetree/bindings/regulator/regulator.txt.
+    One for each MICBIAS generator (MICBIAS1, MICBIAS2, ...)
+    (all codecs)
+
+    One for each output pin (MICBIAS1A, MIBCIAS1B, MICBIAS2A, ...)
+    (all except CS47L85, WM1840)
+
+    The following following additional property is supported for the generator
+    nodes:
+      - cirrus,ext-cap : Set to 1 if the MICBIAS has external decoupling
+        capacitors attached.
+
+Optional child nodes:
+    micvdd : Node containing initialization data for the micvdd regulator
+    See bindings/regulator/arizona-regulator.txt
+
+    ldo1 : Node containing initialization data for the LDO1 regulator
+    See bindings/regulator/arizona-regulator.txt
+    (cs47l85, wm1840)
+
+Example:
+
+cs47l85@0 {
+	compatible = "cirrus,cs47l85";
+	reg = <0>;
+
+	reset-gpios = <&gpio 0>;
+
+	interrupt-controller;
+	#interrupt-cells = <2>;
+	interrupts = <&host_irq1>;
+	interrupt-parent = <&gic>;
+};
-- 
1.9.1

--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html