Re: [PATCH RESEND 4/5] mtd: nand: atmel: Document the new DT bindings

[Nicolas Ferre <nicolas.ferre@xxxxxxxxx>]

Le 27/01/2017 à 17:42, Boris Brezillon a écrit :
> Document the new DT bindings for the Atmel NAND controller and
> deprecate the old ones.
> 
> Signed-off-by: Boris Brezillon <boris.brezillon@xxxxxxxxxxxxxxxxxx>

Ok with the binding:
Reviewed-by: Nicolas Ferre <nicolas.ferre@xxxxxxxxxxxxx>

> ---
>  .../devicetree/bindings/mtd/atmel-nand.txt         | 106 ++++++++++++++++++++-
>  1 file changed, 105 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
> index 3e7ee99d3949..2a86ef2332dc 100644
> --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt
> +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt
> @@ -1,4 +1,108 @@
> -Atmel NAND flash
> +Atmel NAND flash controller bindings
> +
> +The NAND flash controller node should be defined under the EBI bus (see
> +Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt).
> +One or several NAND devices can be defined under this NAND controller.
> +The NAND controller might be connected to an ECC engine.
> +
> +* NAND controller bindings:
> +
> +Required properties:
> +- compatible: should be one of the following
> +	"atmel,at91rm9200-nand-controller"
> +	"atmel,at91sam9261-nand-controller"
> +	"atmel,at91sam9g45-nand-controller"
> +	"atmel,sama5d3-nand-controller"
> +- ranges: empty ranges property to forward EBI ranges definitions.
> +- #address-cells: should be set to 2.
> +- #size-cells: should be set to 1.
> +- atmel,nfc-io: phandle to the NFC IO block. Only required for sama5d3
> +		controllers.
> +- atmel,nfc-sram: phandle to the NFC SRAM block. Only required for sama5d3
> +		  controllers.
> +
> +Optional properties:
> +- ecc-engine: phandle to the PMECC block. Only meaningful if the SoC embeds
> +	      a PMECC engine.
> +
> +* NAND device/chip bindings:
> +
> +Required properties:
> +- reg: describes the CS lines assigned to the NAND device. If the NAND device
> +       exposes multiple CS lines (multi-dies chips), your reg property will
> +       contain X tuples of 3 entries.
> +       1st entry: the CS line this NAND chip is connected to
> +       2nd entry: the base offset of the memory region assigned to this
> +		  device (always 0)
> +       3rd entry: the memory region size (always 0x800000)
> +
> +Optional properties:
> +- rb-gpios: the GPIO(s) used to check the Ready/Busy status of the NAND.
> +- cs-gpios: the GPIO(s) used to control the CS line.
> +- det-gpios: the GPIO used to detect if a Smartmedia Card is present.
> +- atmel,rb: an integer identifying the native Ready/Busy pin. Only meaningful
> +	    on sama5 SoCs.
> +
> +All generic properties described in
> +Documentation/devicetree/bindings/mtd/{common,nand}.txt also apply to the NAND
> +device node, and NAND partitions should be defined under the NAND node as
> +described in Documentation/devicetree/bindings/mtd/partition.txt.
> +
> +* ECC engine (PMECC) bindings:
> +
> +Required properties:
> +- compatible: should be one of the following
> +	"atmel,at91sam9g45-pmecc"
> +	"atmel,sama5d4-pmecc"
> +	"atmel,sama5d2-pmecc"
> +- reg: should contain 2 register ranges. The first one is pointing to the PMECC
> +       block, and the second one to the PMECC_ERRLOC block.
> +
> +Example:
> +
> +	pmecc: ecc-engine@ffffc070 {
> +		compatible = "atmel,at91sam9g45-pmecc";
> +                reg = <0xffffc070 0x490>,
> +                      <0xffffc500 0x100>;
> +	};
> +
> +	ebi: ebi@10000000 {
> +		compatible = "atmel,sama5d3-ebi";
> +		#address-cells = <2>;
> +		#size-cells = <1>;
> +		atmel,smc = <&hsmc>;
> +		reg = <0x10000000 0x10000000
> +		       0x40000000 0x30000000>;
> +		ranges = <0x0 0x0 0x10000000 0x10000000
> +			  0x1 0x0 0x40000000 0x10000000
> +			  0x2 0x0 0x50000000 0x10000000
> +			  0x3 0x0 0x60000000 0x10000000>;
> +		clocks = <&mck>;
> +
> +                nand_controller: nand-controller {
> +			compatible = "atmel,sama5d3-nand-controller";
> +			atmel,nfc-sram = <&nfc_sram>;
> +			atmel,nfc-io = <&nfc_io>;
> +			ecc-engine = <&pmecc>;
> +			#address-cells = <2>;
> +			#size-cells = <1>;
> +			ranges;
> +
> +			nand@3 {
> +				reg = <0x3 0x0 0x800000>;
> +				atmel,rb = <0>;
> +
> +				/*
> +				 * Put generic NAND/MTD properties and
> +				 * subnodes here.
> +				 */
> +			};
> +		};
> +	};
> +
> +-----------------------------------------------------------------------
> +
> +Deprecated bindings (should not be used in new device trees):
>  
>  Required properties:
>  - compatible: The possible values are:
> 


-- 
Nicolas Ferre
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html