Re: [PATCH v2 04/12] driver: clk: imx: Add clock driver for imx6sll

[Stephen Boyd <sboyd@xxxxxxxxxxxxxx>]

On 01/13, Jacky Bai wrote:
> > >
> > > The reason why we enable these two clks here is in below commit commit
> > > a5120e89e7e187a91852896f586876c7a2030804
> > > Author: Peter Chen <peter.chen@xxxxxxxxxxxxx>
> > > Date:   Fri Jan 18 10:38:05 2013 +0800
> > >       ARM i.MX6: change mxs usbphy clock usage
> > >
> > 
> > So can we mark these clks with CLK_IS_CRITICAL flag then instead?
> > Or are they disabled out of the bootloader?
> > 
> 
> Sure, using 'CLK_IS_CRITICAL'  should be ok for clks_init_on clocks.  But for  USBPHY*_GATE, it is
> only enabled when CONIG_USB_MXC_PHY is true.  And another concern is if we need to add CLK_IS_CRITICAL
> flag to clks_init_on clocks, we may need to add new wrapper function to register these critical clock. It is not very good.

Ok so set the critical flag when CONFIG_USB_MXC_PHY is enabled?
That isn't too hard to do.

> 
>  > >
> > > > > +	}
> > > > > +
> > > > > +	/* Lower the AHB clock rate before changing the clock source. */
> > > > > +	clk_set_rate(clks[IMX6SLL_CLK_AHB], 99000000);
> > > > > +
> > > > > +	/* Change periph_pre clock to pll2_bus to adjust AXI rate to 264MHz */
> > > > > +	clk_set_parent(clks[IMX6SLL_CLK_PERIPH_CLK2_SEL],
> > > > clks[IMX6SLL_CLK_PLL3_USB_OTG]);
> > > > > +	clk_set_parent(clks[IMX6SLL_CLK_PERIPH],
> > > > clks[IMX6SLL_CLK_PERIPH_CLK2]);
> > > > > +	clk_set_parent(clks[IMX6SLL_CLK_PERIPH_PRE],
> > > > clks[IMX6SLL_CLK_PLL2_BUS]);
> > > > > +	clk_set_parent(clks[IMX6SLL_CLK_PERIPH],
> > > > > +clks[IMX6SLL_CLK_PERIPH_PRE]);
> > > > > +
> > > > > +	clk_set_rate(clks[IMX6SLL_CLK_AHB], 132000000);
> > > >
> > > > assigned-clocks for rates now? Or perhaps we shouldn't be exposing
> > > > these as clks if they have some sort of complicated rate sequence
> > > > switch that we can't guarantee with the clk_ops we have today.
> > >
> > > These clks will be used by some peripherals, so we need to expose these
> > clocks.
> > > And the above parent and rate swith sequence is not very easy to be
> > > handled in assigned-clocks, So we leave it in this place.
> > >
> > 
> > How do we guarantee that the rate switch doesn't happen later on, requiring
> > this coordinated sequence of clk operations?
> > 
> 
> This clock sequence is used for increasing the AXI and AHB bus clock rate. In normal
> use, it is very rarely that we need to change them again. If we really need to change
> AXI and AHB bus clock later, a similar sequence must be used to do this.
> 

Ok. It feels unsafe, so please make sure no child clocks have the
CLK_SET_RATE_PARENT flag set so we can't randomly change the rate
of this clk outside of this init code.

-- 
Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
a Linux Foundation Collaborative Project
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html