Re: [PATCH 07/12] dt-bindings: i2c: Add support for 'i2c-bus' subnode

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On 2016-06-23 17:59, Jon Hunter wrote:
> The I2C driver core for boards using device-tree assumes any subnode of
> an I2C adapter in the device-tree blob as being a I2C slave device.
> Although this makes complete sense, some I2C adapters may have subnodes
> which are not I2C slaves but subnodes presenting other features. For
> example some Tegra devices have an I2C interface which may share its
> pins with other devices and to share these pins subnodes for
> representing these pins so they have be shared via the pinctrl framework
> are needed.
> 
> To allow I2C adapters to have non-I2C specific subnodes in device-tree
> that are not parsed by the I2C driver core by adding support for a
> 'i2c-bus' subnode where I2C slaves can be placed. If the 'i2c-bus'
> subnode is present then all I2C slaves must be placed under this subnode.
> 
> Signed-off-by: Jon Hunter <jonathanh@xxxxxxxxxx>
> Acked-by: Thierry Reding <treding@xxxxxxxxxx>
> ---
>  Documentation/devicetree/bindings/i2c/i2c.txt | 8 ++++++++
>  1 file changed, 8 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/i2c/i2c.txt b/Documentation/devicetree/bindings/i2c/i2c.txt
> index f31b2ad1552b..71bea55d4c1b 100644
> --- a/Documentation/devicetree/bindings/i2c/i2c.txt
> +++ b/Documentation/devicetree/bindings/i2c/i2c.txt
> @@ -32,6 +32,14 @@ wants to support one of the below features, it should adapt the bindings below.
>  - clock-frequency
>  	frequency of bus clock in Hz.
>  
> +- i2c-bus
> +	For I2C adapters that have child nodes that are a mixture of both I2C
> +	devices and non-I2C devices (such as a pin controller), the 'i2c-bus'
> +	subnode can be used for populating I2C devices. If the 'i2c-bus'
> +	subnode is present, only subnodes of this will be considered as I2C
> +	slaves. The properties, '#address-cells' and '#size-cells' must be
> +	defined under this subnode if present.

Hmmm, those #-properties are listed above, under "Required properties", which
is no longer 100% true. Maybe rephrase to

	slaves. The required properties '#address-cells' and '#size-cells'
	must be	defined under this subnode instead, if this subnode is present.

to make the rules (even) clearer?

Cheers,
Peter

> +
>  - i2c-scl-falling-time-ns
>  	Number of nanoseconds the SCL signal takes to fall; t(f) in the I2C
>  	specification.
> 

--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux