[PATCH V12 2/2] pinctrl: max77620: add pincontrol driver for MAX77620/MAX20024

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



MAXIM Semiconductor's PMIC, MAX77620/MAX20024 has 8 GPIO pins
which also act as the special function in alternate mode. Also
there is configuration like push-pull, open drain, FPS timing
etc for these pins.

Add pin control driver to configure these parameters through
pin control APIs.

Signed-off-by: Laxman Dewangan <ldewangan@xxxxxxxxxx>
Reviewed-by: Linus Walleij <linus.walleij@xxxxxxxxxx>

---
This was part of the max77620 series and mfd is merged. So it
can go in subsystem wise.

Changes from V1:
- Cleanup code based on comment received on mfd/rtc.
- Avoid duplication on error message.

Changes form V2:
- Run coccicheck and checkpatch in strict mode for the alignment.
- update based on api changes from core.

Changes from V3:
- Change all sys initcall to module driver.
- change the max77620_read argument to unisgned int from u8.

Changes from V4:
- Added DT binding document as devicetree/bindings/pinctrl/pinctrl-max77620.txt
- Detail out properties as per review comment.

Changes from V5:
- Separate out DT binding doc for pincontrol.
- Added reviewed by for Linus W

Changes from V6:
- Use regmap APIs direct instead of max77620 abstraction APIs.

Changes from V7:
- None

Changes from V8:
- Run checkpatch --strict on final patch and fixes issue and changed
  unsigned to unsigned int.

Changes from V9:
None

Changes from V10:
Use new APIs for the dt_free_map.

Changes from V11:
- Change bool to tristate for the CONFIG.
- Use devm_pinctrl_tegister and get rid of remove callback.
---
 drivers/pinctrl/Kconfig            |  10 +
 drivers/pinctrl/Makefile           |   1 +
 drivers/pinctrl/pinctrl-max77620.c | 678 +++++++++++++++++++++++++++++++++++++
 3 files changed, 689 insertions(+)
 create mode 100644 drivers/pinctrl/pinctrl-max77620.c

diff --git a/drivers/pinctrl/Kconfig b/drivers/pinctrl/Kconfig
index fb8200b..612547c 100644
--- a/drivers/pinctrl/Kconfig
+++ b/drivers/pinctrl/Kconfig
@@ -196,6 +196,16 @@ config PINCTRL_COH901
 	  COH 901 335 and COH 901 571/3. They contain 3, 5 or 7
 	  ports of 8 GPIO pins each.
 
+config PINCTRL_MAX77620
+	tristate "MAX77620/MAX20024 Pincontrol support"
+	depends on MFD_MAX77620
+	select GENERIC_PINCONF
+	help
+	  Say Yes here to enable Pin control support for Maxim PMIC MAX77620.
+	  This PMIC has 8 GPIO pins that work as GPIO as well as special
+	  function in alternate mode. This driver also configure push-pull,
+	  open drain, FPS slots etc.
+
 config PINCTRL_PALMAS
 	bool "Pinctrl driver for the PALMAS Series MFD devices"
 	depends on OF && MFD_PALMAS
diff --git a/drivers/pinctrl/Makefile b/drivers/pinctrl/Makefile
index e4bc115..d6f349c 100644
--- a/drivers/pinctrl/Makefile
+++ b/drivers/pinctrl/Makefile
@@ -17,6 +17,7 @@ obj-$(CONFIG_PINCTRL_AMD)	+= pinctrl-amd.o
 obj-$(CONFIG_PINCTRL_DIGICOLOR)	+= pinctrl-digicolor.o
 obj-$(CONFIG_PINCTRL_FALCON)	+= pinctrl-falcon.o
 obj-$(CONFIG_PINCTRL_MESON)	+= meson/
+obj-$(CONFIG_PINCTRL_MAX77620)	+= pinctrl-max77620.o
 obj-$(CONFIG_PINCTRL_PALMAS)	+= pinctrl-palmas.o
 obj-$(CONFIG_PINCTRL_PIC32)	+= pinctrl-pic32.o
 obj-$(CONFIG_PINCTRL_PISTACHIO)	+= pinctrl-pistachio.o
diff --git a/drivers/pinctrl/pinctrl-max77620.c b/drivers/pinctrl/pinctrl-max77620.c
new file mode 100644
index 0000000..19005a0
--- /dev/null
+++ b/drivers/pinctrl/pinctrl-max77620.c
@@ -0,0 +1,678 @@
+/*
+ * MAX77620 pin control driver.
+ *
+ * Copyright (c) 2016, NVIDIA CORPORATION.  All rights reserved.
+ *
+ * Author:
+ *	Chaitanya Bandi <bandik@xxxxxxxxxx>
+ *	Laxman Dewangan <ldewangan@xxxxxxxxxx>
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ */
+
+#include <linux/mfd/max77620.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/pinctrl/pinctrl.h>
+#include <linux/pinctrl/pinconf-generic.h>
+#include <linux/pinctrl/pinconf.h>
+#include <linux/pinctrl/pinmux.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+#include "core.h"
+#include "pinconf.h"
+#include "pinctrl-utils.h"
+
+#define MAX77620_PIN_NUM 8
+
+enum max77620_pin_ppdrv {
+	MAX77620_PIN_UNCONFIG_DRV,
+	MAX77620_PIN_OD_DRV,
+	MAX77620_PIN_PP_DRV,
+};
+
+enum max77620_pinconf_param {
+	MAX77620_ACTIVE_FPS_SOURCE = PIN_CONFIG_END + 1,
+	MAX77620_ACTIVE_FPS_POWER_ON_SLOTS,
+	MAX77620_ACTIVE_FPS_POWER_DOWN_SLOTS,
+	MAX77620_SUSPEND_FPS_SOURCE,
+	MAX77620_SUSPEND_FPS_POWER_ON_SLOTS,
+	MAX77620_SUSPEND_FPS_POWER_DOWN_SLOTS,
+};
+
+struct max77620_pin_function {
+	const char *name;
+	const char * const *groups;
+	unsigned int ngroups;
+	int mux_option;
+};
+
+struct max77620_cfg_param {
+	const char *property;
+	enum max77620_pinconf_param param;
+};
+
+static const struct pinconf_generic_params max77620_cfg_params[] = {
+	{
+		.property = "maxim,active-fps-source",
+		.param = MAX77620_ACTIVE_FPS_SOURCE,
+	}, {
+		.property = "maxim,active-fps-power-up-slot",
+		.param = MAX77620_ACTIVE_FPS_POWER_ON_SLOTS,
+	}, {
+		.property = "maxim,active-fps-power-down-slot",
+		.param = MAX77620_ACTIVE_FPS_POWER_DOWN_SLOTS,
+	}, {
+		.property = "maxim,suspend-fps-source",
+		.param = MAX77620_SUSPEND_FPS_SOURCE,
+	}, {
+		.property = "maxim,suspend-fps-power-up-slot",
+		.param = MAX77620_SUSPEND_FPS_POWER_ON_SLOTS,
+	}, {
+		.property = "maxim,suspend-fps-power-down-slot",
+		.param = MAX77620_SUSPEND_FPS_POWER_DOWN_SLOTS,
+	},
+};
+
+enum max77620_alternate_pinmux_option {
+	MAX77620_PINMUX_GPIO				= 0,
+	MAX77620_PINMUX_LOW_POWER_MODE_CONTROL_IN	= 1,
+	MAX77620_PINMUX_FLEXIBLE_POWER_SEQUENCER_OUT	= 2,
+	MAX77620_PINMUX_32K_OUT1			= 3,
+	MAX77620_PINMUX_SD0_DYNAMIC_VOLTAGE_SCALING_IN	= 4,
+	MAX77620_PINMUX_SD1_DYNAMIC_VOLTAGE_SCALING_IN	= 5,
+	MAX77620_PINMUX_REFERENCE_OUT			= 6,
+};
+
+struct max77620_pingroup {
+	const char *name;
+	const unsigned int pins[1];
+	unsigned int npins;
+	enum max77620_alternate_pinmux_option alt_option;
+};
+
+struct max77620_pin_info {
+	enum max77620_pin_ppdrv drv_type;
+	int pull_config;
+};
+
+struct max77620_fps_config {
+	int active_fps_src;
+	int active_power_up_slots;
+	int active_power_down_slots;
+	int suspend_fps_src;
+	int suspend_power_up_slots;
+	int suspend_power_down_slots;
+};
+
+struct max77620_pctrl_info {
+	struct device *dev;
+	struct pinctrl_dev *pctl;
+	struct regmap *rmap;
+	int pins_current_opt[MAX77620_GPIO_NR];
+	const struct max77620_pin_function *functions;
+	unsigned int num_functions;
+	const struct max77620_pingroup *pin_groups;
+	int num_pin_groups;
+	const struct pinctrl_pin_desc *pins;
+	unsigned int num_pins;
+	struct max77620_pin_info pin_info[MAX77620_PIN_NUM];
+	struct max77620_fps_config fps_config[MAX77620_PIN_NUM];
+};
+
+static const struct pinctrl_pin_desc max77620_pins_desc[] = {
+	PINCTRL_PIN(MAX77620_GPIO0, "gpio0"),
+	PINCTRL_PIN(MAX77620_GPIO1, "gpio1"),
+	PINCTRL_PIN(MAX77620_GPIO2, "gpio2"),
+	PINCTRL_PIN(MAX77620_GPIO3, "gpio3"),
+	PINCTRL_PIN(MAX77620_GPIO4, "gpio4"),
+	PINCTRL_PIN(MAX77620_GPIO5, "gpio5"),
+	PINCTRL_PIN(MAX77620_GPIO6, "gpio6"),
+	PINCTRL_PIN(MAX77620_GPIO7, "gpio7"),
+};
+
+static const char * const gpio_groups[] = {
+	"gpio0",
+	"gpio1",
+	"gpio2",
+	"gpio3",
+	"gpio4",
+	"gpio5",
+	"gpio6",
+	"gpio7",
+};
+
+#define FUNCTION_GROUP(fname, mux)			\
+	{						\
+		.name = fname,				\
+		.groups = gpio_groups,			\
+		.ngroups = ARRAY_SIZE(gpio_groups),	\
+		.mux_option = MAX77620_PINMUX_##mux,	\
+	}
+
+static const struct max77620_pin_function max77620_pin_function[] = {
+	FUNCTION_GROUP("gpio", GPIO),
+	FUNCTION_GROUP("lpm-control-in", LOW_POWER_MODE_CONTROL_IN),
+	FUNCTION_GROUP("fps-out", FLEXIBLE_POWER_SEQUENCER_OUT),
+	FUNCTION_GROUP("32k-out1", 32K_OUT1),
+	FUNCTION_GROUP("sd0-dvs-in", SD0_DYNAMIC_VOLTAGE_SCALING_IN),
+	FUNCTION_GROUP("sd1-dvs-in", SD1_DYNAMIC_VOLTAGE_SCALING_IN),
+	FUNCTION_GROUP("reference-out", REFERENCE_OUT),
+};
+
+#define MAX77620_PINGROUP(pg_name, pin_id, option) \
+	{								\
+		.name = #pg_name,					\
+		.pins = {MAX77620_##pin_id},				\
+		.npins = 1,						\
+		.alt_option = MAX77620_PINMUX_##option,			\
+	}
+
+static const struct max77620_pingroup max77620_pingroups[] = {
+	MAX77620_PINGROUP(gpio0, GPIO0, LOW_POWER_MODE_CONTROL_IN),
+	MAX77620_PINGROUP(gpio1, GPIO1, FLEXIBLE_POWER_SEQUENCER_OUT),
+	MAX77620_PINGROUP(gpio2, GPIO2, FLEXIBLE_POWER_SEQUENCER_OUT),
+	MAX77620_PINGROUP(gpio3, GPIO3, FLEXIBLE_POWER_SEQUENCER_OUT),
+	MAX77620_PINGROUP(gpio4, GPIO4, 32K_OUT1),
+	MAX77620_PINGROUP(gpio5, GPIO5, SD0_DYNAMIC_VOLTAGE_SCALING_IN),
+	MAX77620_PINGROUP(gpio6, GPIO6, SD1_DYNAMIC_VOLTAGE_SCALING_IN),
+	MAX77620_PINGROUP(gpio7, GPIO7, REFERENCE_OUT),
+};
+
+static int max77620_pinctrl_get_groups_count(struct pinctrl_dev *pctldev)
+{
+	struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+
+	return mpci->num_pin_groups;
+}
+
+static const char *max77620_pinctrl_get_group_name(
+		struct pinctrl_dev *pctldev, unsigned int group)
+{
+	struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+
+	return mpci->pin_groups[group].name;
+}
+
+static int max77620_pinctrl_get_group_pins(
+		struct pinctrl_dev *pctldev, unsigned int group,
+		const unsigned int **pins, unsigned int *num_pins)
+{
+	struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+
+	*pins = mpci->pin_groups[group].pins;
+	*num_pins = mpci->pin_groups[group].npins;
+
+	return 0;
+}
+
+static const struct pinctrl_ops max77620_pinctrl_ops = {
+	.get_groups_count = max77620_pinctrl_get_groups_count,
+	.get_group_name = max77620_pinctrl_get_group_name,
+	.get_group_pins = max77620_pinctrl_get_group_pins,
+	.dt_node_to_map = pinconf_generic_dt_node_to_map_pin,
+	.dt_free_map = pinctrl_utils_free_map,
+};
+
+static int max77620_pinctrl_get_funcs_count(struct pinctrl_dev *pctldev)
+{
+	struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+
+	return mpci->num_functions;
+}
+
+static const char *max77620_pinctrl_get_func_name(struct pinctrl_dev *pctldev,
+						  unsigned int function)
+{
+	struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+
+	return mpci->functions[function].name;
+}
+
+static int max77620_pinctrl_get_func_groups(struct pinctrl_dev *pctldev,
+					    unsigned int function,
+					    const char * const **groups,
+					    unsigned int * const num_groups)
+{
+	struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+
+	*groups = mpci->functions[function].groups;
+	*num_groups = mpci->functions[function].ngroups;
+
+	return 0;
+}
+
+static int max77620_pinctrl_enable(struct pinctrl_dev *pctldev,
+				   unsigned int function, unsigned int group)
+{
+	struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+	u8 val;
+	int ret;
+
+	if (function == MAX77620_PINMUX_GPIO) {
+		val = 0;
+	} else if (function == mpci->pin_groups[group].alt_option) {
+		val = 1 << group;
+	} else {
+		dev_err(mpci->dev, "GPIO %u doesn't have function %u\n",
+			group, function);
+		return -EINVAL;
+	}
+	ret = regmap_update_bits(mpci->rmap, MAX77620_REG_AME_GPIO,
+				 BIT(group), val);
+	if (ret < 0)
+		dev_err(mpci->dev, "REG AME GPIO update failed: %d\n", ret);
+
+	return ret;
+}
+
+static const struct pinmux_ops max77620_pinmux_ops = {
+	.get_functions_count	= max77620_pinctrl_get_funcs_count,
+	.get_function_name	= max77620_pinctrl_get_func_name,
+	.get_function_groups	= max77620_pinctrl_get_func_groups,
+	.set_mux		= max77620_pinctrl_enable,
+};
+
+static int max77620_pinconf_get(struct pinctrl_dev *pctldev,
+				unsigned int pin, unsigned long *config)
+{
+	struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+	struct device *dev = mpci->dev;
+	enum pin_config_param param = pinconf_to_config_param(*config);
+	unsigned int val;
+	int arg = 0;
+	int ret;
+
+	switch (param) {
+	case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+		if (mpci->pin_info[pin].drv_type == MAX77620_PIN_OD_DRV)
+			arg = 1;
+		break;
+
+	case PIN_CONFIG_DRIVE_PUSH_PULL:
+		if (mpci->pin_info[pin].drv_type == MAX77620_PIN_PP_DRV)
+			arg = 1;
+		break;
+
+	case PIN_CONFIG_BIAS_PULL_UP:
+		ret = regmap_read(mpci->rmap, MAX77620_REG_PUE_GPIO, &val);
+		if (ret < 0) {
+			dev_err(dev, "Reg PUE_GPIO read failed: %d\n", ret);
+			return ret;
+		}
+		if (val & BIT(pin))
+			arg = 1;
+		break;
+
+	case PIN_CONFIG_BIAS_PULL_DOWN:
+		ret = regmap_read(mpci->rmap, MAX77620_REG_PDE_GPIO, &val);
+		if (ret < 0) {
+			dev_err(dev, "Reg PDE_GPIO read failed: %d\n", ret);
+			return ret;
+		}
+		if (val & BIT(pin))
+			arg = 1;
+		break;
+
+	default:
+		dev_err(dev, "Properties not supported\n");
+		return -ENOTSUPP;
+	}
+
+	*config = pinconf_to_config_packed(param, (u16)arg);
+
+	return 0;
+}
+
+static int max77620_get_default_fps(struct max77620_pctrl_info *mpci,
+				    int addr, int *fps)
+{
+	unsigned int val;
+	int ret;
+
+	ret = regmap_read(mpci->rmap, addr, &val);
+	if (ret < 0) {
+		dev_err(mpci->dev, "Reg PUE_GPIO read failed: %d\n", ret);
+		return ret;
+	}
+	*fps = (val & MAX77620_FPS_SRC_MASK) >> MAX77620_FPS_SRC_SHIFT;
+
+	return 0;
+}
+
+static int max77620_set_fps_param(struct max77620_pctrl_info *mpci,
+				  int pin, int param)
+{
+	struct max77620_fps_config *fps_config = &mpci->fps_config[pin];
+	int addr, ret;
+	int param_val;
+	int mask, shift;
+
+	if ((pin < MAX77620_GPIO1) || (pin > MAX77620_GPIO3))
+		return 0;
+
+	addr = MAX77620_REG_FPS_GPIO1 + pin - 1;
+	switch (param) {
+	case MAX77620_ACTIVE_FPS_SOURCE:
+	case MAX77620_SUSPEND_FPS_SOURCE:
+		mask = MAX77620_FPS_SRC_MASK;
+		shift = MAX77620_FPS_SRC_SHIFT;
+		param_val = fps_config->active_fps_src;
+		if (param == MAX77620_SUSPEND_FPS_SOURCE)
+			param_val = fps_config->suspend_fps_src;
+		break;
+
+	case MAX77620_ACTIVE_FPS_POWER_ON_SLOTS:
+	case MAX77620_SUSPEND_FPS_POWER_ON_SLOTS:
+		mask = MAX77620_FPS_PU_PERIOD_MASK;
+		shift = MAX77620_FPS_PU_PERIOD_SHIFT;
+		param_val = fps_config->active_power_up_slots;
+		if (param == MAX77620_SUSPEND_FPS_POWER_ON_SLOTS)
+			param_val = fps_config->suspend_power_up_slots;
+		break;
+
+	case MAX77620_ACTIVE_FPS_POWER_DOWN_SLOTS:
+	case MAX77620_SUSPEND_FPS_POWER_DOWN_SLOTS:
+		mask = MAX77620_FPS_PD_PERIOD_MASK;
+		shift = MAX77620_FPS_PD_PERIOD_SHIFT;
+		param_val = fps_config->active_power_down_slots;
+		if (param == MAX77620_SUSPEND_FPS_POWER_DOWN_SLOTS)
+			param_val = fps_config->suspend_power_down_slots;
+		break;
+
+	default:
+		dev_err(mpci->dev, "Invalid parameter %d for pin %d\n",
+			param, pin);
+		return -EINVAL;
+	}
+
+	if (param_val < 0)
+		return 0;
+
+	ret = regmap_update_bits(mpci->rmap, addr, mask, param_val << shift);
+	if (ret < 0)
+		dev_err(mpci->dev, "Reg 0x%02x update failed %d\n", addr, ret);
+
+	return ret;
+}
+
+static int max77620_pinconf_set(struct pinctrl_dev *pctldev,
+				unsigned int pin, unsigned long *configs,
+				unsigned int num_configs)
+{
+	struct max77620_pctrl_info *mpci = pinctrl_dev_get_drvdata(pctldev);
+	struct device *dev = mpci->dev;
+	struct max77620_fps_config *fps_config;
+	int param;
+	u16 param_val;
+	unsigned int val;
+	unsigned int pu_val;
+	unsigned int pd_val;
+	int addr, ret;
+	int i;
+
+	for (i = 0; i < num_configs; i++) {
+		param = pinconf_to_config_param(configs[i]);
+		param_val = pinconf_to_config_argument(configs[i]);
+
+		switch (param) {
+		case PIN_CONFIG_DRIVE_OPEN_DRAIN:
+			val = param_val ? 0 : 1;
+			ret = regmap_update_bits(mpci->rmap,
+						 MAX77620_REG_GPIO0 + pin,
+						 MAX77620_CNFG_GPIO_DRV_MASK,
+						 val);
+			if (ret < 0) {
+				dev_err(dev, "Reg 0x%02x update failed %d\n",
+					MAX77620_REG_GPIO0 + pin, ret);
+				return ret;
+			}
+			mpci->pin_info[pin].drv_type = val ?
+				MAX77620_PIN_PP_DRV : MAX77620_PIN_OD_DRV;
+			break;
+
+		case PIN_CONFIG_DRIVE_PUSH_PULL:
+			val = param_val ? 1 : 0;
+			ret = regmap_update_bits(mpci->rmap,
+						 MAX77620_REG_GPIO0 + pin,
+						 MAX77620_CNFG_GPIO_DRV_MASK,
+						 val);
+			if (ret < 0) {
+				dev_err(dev, "Reg 0x%02x update failed %d\n",
+					MAX77620_REG_GPIO0 + pin, ret);
+				return ret;
+			}
+			mpci->pin_info[pin].drv_type = val ?
+				MAX77620_PIN_PP_DRV : MAX77620_PIN_OD_DRV;
+			break;
+
+		case MAX77620_ACTIVE_FPS_SOURCE:
+		case MAX77620_ACTIVE_FPS_POWER_ON_SLOTS:
+		case MAX77620_ACTIVE_FPS_POWER_DOWN_SLOTS:
+			if ((pin < MAX77620_GPIO1) || (pin > MAX77620_GPIO3))
+				return -EINVAL;
+
+			fps_config = &mpci->fps_config[pin];
+
+			if ((param == MAX77620_ACTIVE_FPS_SOURCE) &&
+			    (param_val == MAX77620_FPS_SRC_DEF)) {
+				addr = MAX77620_REG_FPS_GPIO1 + pin - 1;
+				ret = max77620_get_default_fps(
+						mpci, addr,
+						&fps_config->active_fps_src);
+				if (ret < 0)
+					return ret;
+				break;
+			}
+
+			if (param == MAX77620_ACTIVE_FPS_SOURCE)
+				fps_config->active_fps_src = param_val;
+			else if (param == MAX77620_ACTIVE_FPS_POWER_ON_SLOTS)
+				fps_config->active_power_up_slots = param_val;
+			else
+				fps_config->active_power_down_slots = param_val;
+
+			ret = max77620_set_fps_param(mpci, pin, param);
+			if (ret < 0)
+				return ret;
+			break;
+
+		case MAX77620_SUSPEND_FPS_SOURCE:
+		case MAX77620_SUSPEND_FPS_POWER_ON_SLOTS:
+		case MAX77620_SUSPEND_FPS_POWER_DOWN_SLOTS:
+			if ((pin < MAX77620_GPIO1) || (pin > MAX77620_GPIO3))
+				return -EINVAL;
+
+			fps_config = &mpci->fps_config[pin];
+
+			if ((param == MAX77620_SUSPEND_FPS_SOURCE) &&
+			    (param_val == MAX77620_FPS_SRC_DEF)) {
+				addr = MAX77620_REG_FPS_GPIO1 + pin - 1;
+				ret = max77620_get_default_fps(
+						mpci, addr,
+						&fps_config->suspend_fps_src);
+				if (ret < 0)
+					return ret;
+				break;
+			}
+
+			if (param == MAX77620_SUSPEND_FPS_SOURCE)
+				fps_config->suspend_fps_src = param_val;
+			else if (param == MAX77620_SUSPEND_FPS_POWER_ON_SLOTS)
+				fps_config->suspend_power_up_slots = param_val;
+			else
+				fps_config->suspend_power_down_slots =
+								param_val;
+			break;
+
+		case PIN_CONFIG_BIAS_PULL_UP:
+		case PIN_CONFIG_BIAS_PULL_DOWN:
+			pu_val = (param == PIN_CONFIG_BIAS_PULL_UP) ?
+							BIT(pin) : 0;
+			pd_val = (param == PIN_CONFIG_BIAS_PULL_DOWN) ?
+							BIT(pin) : 0;
+
+			ret = regmap_update_bits(mpci->rmap,
+						 MAX77620_REG_PUE_GPIO,
+						 BIT(pin), pu_val);
+			if (ret < 0) {
+				dev_err(dev, "PUE_GPIO update failed: %d\n",
+					ret);
+				return ret;
+			}
+
+			ret = regmap_update_bits(mpci->rmap,
+						 MAX77620_REG_PDE_GPIO,
+						 BIT(pin), pd_val);
+			if (ret < 0) {
+				dev_err(dev, "PDE_GPIO update failed: %d\n",
+					ret);
+				return ret;
+			}
+			break;
+
+		default:
+			dev_err(dev, "Properties not supported\n");
+			return -ENOTSUPP;
+		}
+	}
+
+	return 0;
+}
+
+static const struct pinconf_ops max77620_pinconf_ops = {
+	.pin_config_get = max77620_pinconf_get,
+	.pin_config_set = max77620_pinconf_set,
+};
+
+static struct pinctrl_desc max77620_pinctrl_desc = {
+	.pctlops = &max77620_pinctrl_ops,
+	.pmxops = &max77620_pinmux_ops,
+	.confops = &max77620_pinconf_ops,
+};
+
+static int max77620_pinctrl_probe(struct platform_device *pdev)
+{
+	struct max77620_chip *max77620 = dev_get_drvdata(pdev->dev.parent);
+	struct max77620_pctrl_info *mpci;
+	int i;
+
+	mpci = devm_kzalloc(&pdev->dev, sizeof(*mpci), GFP_KERNEL);
+	if (!mpci)
+		return -ENOMEM;
+
+	mpci->dev = &pdev->dev;
+	mpci->dev->of_node = pdev->dev.parent->of_node;
+	mpci->rmap = max77620->rmap;
+
+	mpci->pins = max77620_pins_desc;
+	mpci->num_pins = ARRAY_SIZE(max77620_pins_desc);
+	mpci->functions = max77620_pin_function;
+	mpci->num_functions = ARRAY_SIZE(max77620_pin_function);
+	mpci->pin_groups = max77620_pingroups;
+	mpci->num_pin_groups = ARRAY_SIZE(max77620_pingroups);
+	platform_set_drvdata(pdev, mpci);
+
+	max77620_pinctrl_desc.name = dev_name(&pdev->dev);
+	max77620_pinctrl_desc.pins = max77620_pins_desc;
+	max77620_pinctrl_desc.npins = ARRAY_SIZE(max77620_pins_desc);
+	max77620_pinctrl_desc.num_custom_params =
+				ARRAY_SIZE(max77620_cfg_params);
+	max77620_pinctrl_desc.custom_params = max77620_cfg_params;
+
+	for (i = 0; i < MAX77620_PIN_NUM; ++i) {
+		mpci->fps_config[i].active_fps_src = -1;
+		mpci->fps_config[i].active_power_up_slots = -1;
+		mpci->fps_config[i].active_power_down_slots = -1;
+		mpci->fps_config[i].suspend_fps_src = -1;
+		mpci->fps_config[i].suspend_power_up_slots = -1;
+		mpci->fps_config[i].suspend_power_down_slots = -1;
+	}
+
+	mpci->pctl = devm_pinctrl_register(&pdev->dev, &max77620_pinctrl_desc,
+					   mpci);
+	if (IS_ERR(mpci->pctl)) {
+		dev_err(&pdev->dev, "Couldn't register pinctrl driver\n");
+		return PTR_ERR(mpci->pctl);
+	}
+
+	return 0;
+}
+
+#ifdef CONFIG_PM_SLEEP
+static int max77620_suspend_fps_param[] = {
+	MAX77620_SUSPEND_FPS_SOURCE,
+	MAX77620_SUSPEND_FPS_POWER_ON_SLOTS,
+	MAX77620_SUSPEND_FPS_POWER_DOWN_SLOTS,
+};
+
+static int max77620_active_fps_param[] = {
+	MAX77620_ACTIVE_FPS_SOURCE,
+	MAX77620_ACTIVE_FPS_POWER_ON_SLOTS,
+	MAX77620_ACTIVE_FPS_POWER_DOWN_SLOTS,
+};
+
+static int max77620_pinctrl_suspend(struct device *dev)
+{
+	struct max77620_pctrl_info *mpci = dev_get_drvdata(dev);
+	int pin, p;
+
+	for (pin = 0; pin < MAX77620_PIN_NUM; ++pin) {
+		if ((pin < MAX77620_GPIO1) || (pin > MAX77620_GPIO3))
+			continue;
+		for (p = 0; p < 3; ++p)
+			max77620_set_fps_param(
+				mpci, pin, max77620_suspend_fps_param[p]);
+	}
+
+	return 0;
+};
+
+static int max77620_pinctrl_resume(struct device *dev)
+{
+	struct max77620_pctrl_info *mpci = dev_get_drvdata(dev);
+	int pin, p;
+
+	for (pin = 0; pin < MAX77620_PIN_NUM; ++pin) {
+		if ((pin < MAX77620_GPIO1) || (pin > MAX77620_GPIO3))
+			continue;
+		for (p = 0; p < 3; ++p)
+			max77620_set_fps_param(
+				mpci, pin, max77620_active_fps_param[p]);
+	}
+
+	return 0;
+}
+#endif
+
+static const struct dev_pm_ops max77620_pinctrl_pm_ops = {
+	SET_SYSTEM_SLEEP_PM_OPS(
+		max77620_pinctrl_suspend, max77620_pinctrl_resume)
+};
+
+static const struct platform_device_id max77620_pinctrl_devtype[] = {
+	{ .name = "max77620-pinctrl", },
+	{ .name = "max20024-pinctrl", },
+	{},
+};
+MODULE_DEVICE_TABLE(platform, max77620_pinctrl_devtype);
+
+static struct platform_driver max77620_pinctrl_driver = {
+	.driver = {
+		.name = "max77620-pinctrl",
+		.pm = &max77620_pinctrl_pm_ops,
+	},
+	.probe = max77620_pinctrl_probe,
+	.id_table = max77620_pinctrl_devtype,
+};
+
+module_platform_driver(max77620_pinctrl_driver);
+
+MODULE_DESCRIPTION("MAX77620/MAX20024 pin control driver");
+MODULE_AUTHOR("Chaitanya Bandi<bandik@xxxxxxxxxx>");
+MODULE_AUTHOR("Laxman Dewangan<ldewangan@xxxxxxxxxx>");
+MODULE_ALIAS("platform:max77620-pinctrl");
+MODULE_LICENSE("GPL v2");
-- 
2.1.4

--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux