Re: [PATCH] pinctrl: sunxi: Add H3 R_PIO controller support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Tue, Feb 02, 2016 at 02:25:18PM +0800, Chen-Yu Tsai wrote:
On Mon, Feb 1, 2016 at 6:12 PM, Krzysztof Adamski <k@xxxxxxxx> wrote:
- reg: Should contain the register physical address and length for the
diff --git a/arch/arm/boot/dts/sun8i-h3.dtsi
b/arch/arm/boot/dts/sun8i-h3.dtsi
index 1524130e..745f64c 100644
--- a/arch/arm/boot/dts/sun8i-h3.dtsi
+++ b/arch/arm/boot/dts/sun8i-h3.dtsi
@@ -493,5 +493,17 @@
                        interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>,
                                     <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>;
                };
+
+               r_pio: pinctrl@01f02c00 {
+                       compatible = "allwinner,sun8i-h3-r-pinctrl";
+                       reg = <0x01f02c00 0x400>;
+                       interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>;
+                       clocks = <&bus_gates 69>;

This is probably wrong. According to other SoCs all R_ block peripherals
have clock gates and reset controls in the PRCM.

This is problematic. I can find information about reset and gates control for
this peripheral on other SoCs user manuals but there is nothing about it in H3
User Manual
(https://www.dropbox.com/s/nkr9slo1o9x6i1z/Allwinner_H3_Datasheet_V1.1.pdf?dl=0).

Similarly, while I think I can find r_pio clock setup for A33:
https://github.com/allwinner-zh/linux-3.4-sunxi/blob/master/drivers/clk/sunxi/clk-sun8iw5.c

I can't find it for H3, though:
https://github.com/allwinner-zh/linux-3.4-sunxi/blob/master/drivers/clk/sunxi/clk-sun8iw7.c

Well, apart from this strange snippet:

// binder r-pio CPUS_APB0_GATE to pio-clk's gate-reset-register
   clk = clk_get(NULL,"pio");
   if(!clk || IS_ERR(clk))
       printk("Error not get clk pio\n");
   else
   {
       struct clk_hw *hw = __clk_get_hw(clk);
       struct sunxi_clk_periph *periph = to_clk_periph(hw);
       struct sunxi_clk_periph_gate *gate = &periph->gate;
       gate->reset = sunxi_clk_cpus_base+CPUS_APB0_GATE ;
       gate->rst_shift = 0;
       clk_put(clk);
   }


Which I have to admit I don't fully understand. This seems to be setting reset
line for first pio, not for r_pio - something we don't have right now. Or am I
wrong here?

I'm new to Allwinner SoCs, any help from veterans?

Also, if that proves anything, I did test this code on OrangePi PC and PL ports
works so their clock is enabled, for sure.

Best regards,
Krzysztof Adamski
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux