Re: [PATCH v6 1/7] dt-bindings: mfd: add support for the NXP SIUL2 module

[Krzysztof Kozlowski <krzk@xxxxxxxxxx>]

On 13/11/2024 11:10, Andrei Stefanescu wrote:
> +
> +properties:
> +  compatible:
> +    enum:
> +      - nxp,s32g2-siul2
> +      - nxp,s32g3-siul2

Not much improved. See other NXP bindings how they do this.

> +
> +  reg:
> +    maxItems: 2
> +
> +  reg-names:
> +    items:
> +      - const: siul20
> +      - const: siul21
> +
> +  gpio-controller: true
> +
> +  "#gpio-cells":
> +    const: 2
> +
> +  gpio-ranges:
> +    maxItems: 2
> +
> +  gpio-reserved-ranges:
> +    maxItems: 2

That's odd to always require two reserved ranges. Does this mean all
devices have exactly the same reserved GPIOs? Then the driver should not
export them.

> +
> +  interrupts:
> +    maxItems: 1
> +
> +  interrupt-controller: true
> +
> +  "#interrupt-cells":
> +    const: 2
> +
> +  nvmem-layout:
> +    $ref: /schemas/nvmem/layouts/nvmem-layout.yaml#
> +    description:
> +      This container may reference an NVMEM layout parser.
> +
> +patternProperties:
> +  "-hog(-[0-9]+)?$":
> +    required:
> +      - gpio-hog
> +
> +  "-pins$":
> +    type: object
> +    additionalProperties: false
> +
> +    patternProperties:
> +      "-grp[0-9]$":
> +        type: object
> +        allOf:
> +          - $ref: /schemas/pinctrl/pinmux-node.yaml#
> +          - $ref: /schemas/pinctrl/pincfg-node.yaml#
> +        description:
> +          Pinctrl node's client devices specify pin muxes using subnodes,
> +          which in turn use the standard properties below.
> +
> +        properties:
> +          bias-disable: true
> +          bias-high-impedance: true
> +          bias-pull-up: true
> +          bias-pull-down: true
> +          drive-open-drain: true
> +          input-enable: true
> +          output-enable: true
> +
> +          pinmux:
> +            description: |
> +              An integer array for representing pinmux configurations of
> +              a device. Each integer consists of a PIN_ID and a 4-bit
> +              selected signal source(SSS) as IOMUX setting, which is
> +              calculated as: pinmux = (PIN_ID << 4 | SSS)
> +
> +          slew-rate:
> +            description: Supported slew rate based on Fmax values (MHz)
> +            enum: [83, 133, 150, 166, 208]
> +        required:
> +          - pinmux
> +
> +        additionalProperties: false
> +
> +required:
> +  - compatible
> +  - reg
> +  - reg-names
> +  - gpio-controller
> +  - "#gpio-cells"
> +  - gpio-ranges
> +  - gpio-reserved-ranges
> +  - interrupts
> +  - interrupt-controller
> +  - "#interrupt-cells"
> +
> +additionalProperties: false
> +
> +examples:
> +  - |
> +    #include <dt-bindings/interrupt-controller/arm-gic.h>
> +    #include <dt-bindings/interrupt-controller/irq.h>
> +
> +    siul2@4009c000 {

<form letter>
This is a friendly reminder during the review process.

It seems my or other reviewer's previous comments were not fully
addressed. Maybe the feedback got lost between the quotes, maybe you
just forgot to apply it. Please go back to the previous discussion and
either implement all requested changes or keep discussing them.

Thank you.
</form letter>



Best regards,
Krzysztof