RE: [PATCH v2] pinctrl: samsung: Add support for pull-up and pull-down

["Vishnu Reddy" <vishnu.reddy@xxxxxxxxxxx>]

> -----Original Message-----
> From: Krzysztof Kozlowski [mailto:krzk@xxxxxxxxxx]
> Sent: 24 June 2024 19:27
> To: Vishnu Reddy <vishnu.reddy@xxxxxxxxxxx>;
> krzysztof.kozlowski@xxxxxxxxxx; s.nawrocki@xxxxxxxxxxx;
> alim.akhtar@xxxxxxxxxxx; linus.walleij@xxxxxxxxxx
> Cc: linux-arm-kernel@xxxxxxxxxxxxxxxxxxx; linux-samsung-
> soc@xxxxxxxxxxxxxxx; linux-gpio@xxxxxxxxxxxxxxx; linux-
> kernel@xxxxxxxxxxxxxxx; pankaj.dubey@xxxxxxxxxxx;
> ravi.patel@xxxxxxxxxxx; gost.dev@xxxxxxxxxxx
> Subject: Re: [PATCH v2] pinctrl: samsung: Add support for pull-up and pull-
> down
> 
> On 20/06/2024 12:34, Vishnu Reddy wrote:
> > gpiolib framework has the implementation of setting up the
> > PUD configuration for GPIO pins but there is no driver support.
> >
> > Add support to handle the PUD configuration request from the
> > userspace in samsung pinctrl driver.
> >
> > Signed-off-by: Vishnu Reddy <vishnu.reddy@xxxxxxxxxxx>
> > ---
> > Verified the offset from the user manual of following Exynos SoC series
> > and found the current code is taking care of correct offset for pull-up
> > and pull-down
> >
> > Exynos-3250
> > Exynos-3470
> > Exynos-4412
> > Exynos-4415
> > Exynos-5250
> > Exynos-5260
> > Exynos-5410
> > Exynos-5420
> > Exynos-5422
> > Exynos-7420
> > Exynos-7580
> > Exynos-7880
> > Exynos-9820
> > Exynos-9830
> > Exynos-4210
> > Exynos-S5PC210
> > Exynos-S5PV310
> >
> > This patch is tested on FSD platform
> 
> You verified but...
> 
> > diff --git a/drivers/pinctrl/samsung/pinctrl-samsung.h
> b/drivers/pinctrl/samsung/pinctrl-samsung.h
> > index d50ba6f07d5d..758b623a4bea 100644
> > --- a/drivers/pinctrl/samsung/pinctrl-samsung.h
> > +++ b/drivers/pinctrl/samsung/pinctrl-samsung.h
> > @@ -61,6 +61,13 @@ enum pincfg_type {
> >  #define PIN_CON_FUNC_INPUT		0x0
> >  #define PIN_CON_FUNC_OUTPUT		0x1
> >
> > +/*
> > + * Values for the pin PUD register.
> > + */
> > +#define PIN_PUD_PULL_UP_DOWN_DISABLE	0x0
> > +#define PIN_PUD_PULL_DOWN_ENABLE	0x1
> > +#define PIN_PUD_PULL_UP_ENABLE		0x3
> 
> ... I said it is not correct, so you send the same? If you think I was
> wrong, then please respond and keep discussion going. Sending the same
> suggests you just ignored my comment.
> 
> Look at two headers s5pv210-pinctrl.h and s3c64xx-pinctrl.h. How did you
> resolve these?
Thank you for sharing the s5pv210-pinctrl.h and s3c64xx-pinctrl.h  file names for the pin value information.
I have not ignored your comment. Unfortunately, I don't have the user manuals for the s3c64xx and s5pv210 series.
I have an idea to handle the PIN_PULL_UP value of the s3c64xx and s5pv210 series by checking the compatibility with the of_device_is_compatible API.
Will it be okay or do you have any other suggestions?
> 
> Best regards,
> Krzysztof