[PATCH 7/8] drm/i915: Use the CRC gpio for panel enable/disable

[Shobhit Kumar <shobhit.kumar@xxxxxxxxx>]

The CRC (Crystal Cove) PMIC, controls the panel enable and disable
signals for BYT for dsi panels. This is indicated in the VBT fields. Use
that to initialize and use GPIO based control for these signals.

v2: Use the newer gpiod interface(Alexandre)
v3: Remove the redundant checks and unused code (Ville)

CC: Samuel Ortiz <sameo@xxxxxxxxxxxxxxx>
Cc: Linus Walleij <linus.walleij@xxxxxxxxxx>
Cc: Alexandre Courbot <gnurou@xxxxxxxxx>
Cc: Thierry Reding <thierry.reding@xxxxxxxxx>
Signed-off-by: Shobhit Kumar <shobhit.kumar@xxxxxxxxx>
---
 drivers/gpu/drm/i915/intel_dsi.c | 32 ++++++++++++++++++++++++++++++--
 drivers/gpu/drm/i915/intel_dsi.h |  6 ++++++
 2 files changed, 36 insertions(+), 2 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_dsi.c b/drivers/gpu/drm/i915/intel_dsi.c
index 5196642..be55ffa 100644
--- a/drivers/gpu/drm/i915/intel_dsi.c
+++ b/drivers/gpu/drm/i915/intel_dsi.c
@@ -31,6 +31,7 @@
 #include <drm/drm_panel.h>
 #include <drm/drm_mipi_dsi.h>
 #include <linux/slab.h>
+#include <linux/gpio/consumer.h>
 #include "i915_drv.h"
 #include "intel_drv.h"
 #include "intel_dsi.h"
@@ -415,6 +416,12 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)
 
 	DRM_DEBUG_KMS("\n");
 
+	/* Panel Enable over CRC PMIC */
+	if (intel_dsi->gpio_panel)
+		gpiod_set_value_cansleep(intel_dsi->gpio_panel, 1);
+
+	msleep(intel_dsi->panel_on_delay);
+
 	/* Disable DPOunit clock gating, can stall pipe
 	 * and we need DPLL REFA always enabled */
 	tmp = I915_READ(DPLL(pipe));
@@ -432,8 +439,6 @@ static void intel_dsi_pre_enable(struct intel_encoder *encoder)
 	/* put device in ready state */
 	intel_dsi_device_ready(encoder);
 
-	msleep(intel_dsi->panel_on_delay);
-
 	drm_panel_prepare(intel_dsi->panel);
 
 	for_each_dsi_port(port, intel_dsi->ports)
@@ -576,6 +581,10 @@ static void intel_dsi_post_disable(struct intel_encoder *encoder)
 
 	msleep(intel_dsi->panel_off_delay);
 	msleep(intel_dsi->panel_pwr_cycle_delay);
+
+	/* Panel Disable over CRC PMIC */
+	if (intel_dsi->gpio_panel)
+		gpiod_set_value_cansleep(intel_dsi->gpio_panel, 0);
 }
 
 static bool intel_dsi_get_hw_state(struct intel_encoder *encoder,
@@ -955,6 +964,11 @@ static void intel_dsi_encoder_destroy(struct drm_encoder *encoder)
 		/* XXX: Logically this call belongs in the panel driver. */
 		drm_panel_remove(intel_dsi->panel);
 	}
+
+	/* dispose of the gpios */
+	if (intel_dsi->gpio_panel)
+		gpiod_put(intel_dsi->gpio_panel);
+
 	intel_encoder_destroy(encoder);
 }
 
@@ -1071,6 +1085,20 @@ void intel_dsi_init(struct drm_device *dev)
 		goto err;
 	}
 
+	/*
+	 * In case of BYT with CRC PMIC, we need to use GPIO for
+	 * Panel control.
+	 */
+	if (dev_priv->vbt.dsi.config->pwm_blc == PPS_BLC_PMIC) {
+		intel_dsi->gpio_panel =
+			gpiod_get(dev->dev, "panel", GPIOD_OUT_HIGH);
+
+		if (IS_ERR(intel_dsi->gpio_panel)) {
+			DRM_ERROR("Failed to own gpio for panel control\n");
+			intel_dsi->gpio_panel = NULL;
+		}
+	}
+
 	intel_encoder->type = INTEL_OUTPUT_DSI;
 	intel_encoder->cloneable = 0;
 	drm_connector_init(dev, connector, &intel_dsi_connector_funcs,
diff --git a/drivers/gpu/drm/i915/intel_dsi.h b/drivers/gpu/drm/i915/intel_dsi.h
index 2784ac4..bf1bade 100644
--- a/drivers/gpu/drm/i915/intel_dsi.h
+++ b/drivers/gpu/drm/i915/intel_dsi.h
@@ -29,6 +29,9 @@
 #include <drm/drm_mipi_dsi.h>
 #include "intel_drv.h"
 
+#define PPS_BLC_PMIC   0
+#define PPS_BLC_SOC    1
+
 /* Dual Link support */
 #define DSI_DUAL_LINK_NONE		0
 #define DSI_DUAL_LINK_FRONT_BACK	1
@@ -42,6 +45,9 @@ struct intel_dsi {
 	struct drm_panel *panel;
 	struct intel_dsi_host *dsi_hosts[I915_MAX_PORTS];
 
+	/* GPIO Desc for CRC based Panel control */
+	struct gpio_desc *gpio_panel;
+
 	struct intel_connector *attached_connector;
 
 	/* bit mask of ports being driven */
-- 
2.1.0

--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html