Re: [PATCH V3 2/2] pinctrl: Add Pistachio SoC pin control driver

[Andrew Bresticker <abrestic@xxxxxxxxxxxx>]

On Tue, Apr 28, 2015 at 3:40 PM, Ezequiel Garcia
<ezequiel.garcia@xxxxxxxxxx> wrote:
> Just a silly comment.
>
> On 04/07/2015 04:44 PM, Andrew Bresticker wrote:
> [..]
>> +
>> +static const struct pinmux_ops pistachio_pinmux_ops = {
>> +     .get_functions_count = pistachio_pinmux_get_functions_count,
>> +     .get_function_name = pistachio_pinmux_get_function_name,
>> +     .get_function_groups = pistachio_pinmux_get_function_groups,
>> +     .set_mux = pistachio_pinmux_enable,
>> +};
>> +
>> +static int pistachio_pinconf_get(struct pinctrl_dev *pctldev, unsigned pin,
>> +                              unsigned long *config)
>> +{
>> +     struct pistachio_pinctrl *pctl = pinctrl_dev_get_drvdata(pctldev);
>> +     enum pin_config_param param = pinconf_to_config_param(*config);
>> +     u32 val, arg;
>> +
>> +     switch (param) {
>> +     case PIN_CONFIG_INPUT_SCHMITT_ENABLE:
>> +             val = pctl_readl(pctl, PADS_SCHMITT_EN_REG(pin));
>> +             arg = !!(val & PADS_SCHMITT_EN_BIT(pin));
>> +             break;
>> +     case PIN_CONFIG_BIAS_HIGH_IMPEDANCE:
>> +             val = pctl_readl(pctl, PADS_PU_PD_REG(pin)) >>
>> +                     PADS_PU_PD_SHIFT(pin);
>> +             arg = (val & PADS_PU_PD_MASK) == PADS_PU_PD_HIGHZ;
>> +             break;
>> +     case PIN_CONFIG_BIAS_PULL_UP:
>> +             val = pctl_readl(pctl, PADS_PU_PD_REG(pin)) >>
>> +                     PADS_PU_PD_SHIFT(pin);
>> +             arg = (val & PADS_PU_PD_MASK) == PADS_PU_PD_UP;
>> +             break;
>> +     case PIN_CONFIG_BIAS_PULL_DOWN:
>> +             val = pctl_readl(pctl, PADS_PU_PD_REG(pin)) >>
>> +                     PADS_PU_PD_SHIFT(pin);
>> +             arg = (val & PADS_PU_PD_MASK) == PADS_PU_PD_DOWN;
>> +             break;
>> +     case PIN_CONFIG_BIAS_BUS_HOLD:
>> +             val = pctl_readl(pctl, PADS_PU_PD_REG(pin)) >>
>> +                     PADS_PU_PD_SHIFT(pin);
>> +             arg = (val & PADS_PU_PD_MASK) == PADS_PU_PD_BUS;
>> +             break;
>> +     case PIN_CONFIG_SLEW_RATE:
>> +             val = pctl_readl(pctl, PADS_SLEW_RATE_REG(pin));
>> +             arg = !!(val & PADS_SLEW_RATE_BIT(pin));
>> +             break;
>> +     case PIN_CONFIG_DRIVE_STRENGTH:
>> +             val = pctl_readl(pctl, PADS_DRIVE_STRENGTH_REG(pin)) >>
>> +                     PADS_DRIVE_STRENGTH_SHIFT(pin);
>> +             switch (val & PADS_DRIVE_STRENGTH_MASK) {
>> +             case PADS_DRIVE_STRENGTH_2MA:
>> +                     arg = 2;
>> +                     break;
>> +             case PADS_DRIVE_STRENGTH_4MA:
>> +                     arg = 4;
>> +                     break;
>> +             case PADS_DRIVE_STRENGTH_8MA:
>> +                     arg = 8;
>> +                     break;
>> +             case PADS_DRIVE_STRENGTH_12MA:
>> +             default:
>> +                     arg = 12;
>> +                     break;
>> +             }
>> +             break;
>> +     default:
>> +             dev_err(pctl->dev, "Property %u not supported\n", param);
>
> Probably just a nitpick, but maybe this should be dev_dbg. Otherwise,
> we'll get a ton of these errors when cat'ing pinconf-pins in debugfs.
>
>> +             return -EINVAL;
>
> And this should be -ENOTSUPP. I guess it doesn't matter much.

Ah, you're right.  I meant to this for V3 but I guess I forgot.  Will fix.

-Andrew
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html