Re: [RFC PATCH v2 3/4] serial: at91: Use helpers for gpio irqs

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



2015-01-10 15:32 GMT+01:00 Janusz Uzycki <j.uzycki@xxxxxxxxxxxxxx>:
> The patch updates atmel_serial driver to use new mctrl_gpio helpers for
> gpio irqs. The code is simpler now.
>
> Signed-off-by: Janusz Uzycki <j.uzycki@xxxxxxxxxxxxxx>
> ---
>
> The patch exists since v2.
> Compile-test only - please test it on real hardware.
>
> ---
>  drivers/tty/serial/atmel_serial.c | 123 +++++++-------------------------------
>  1 file changed, 20 insertions(+), 103 deletions(-)
>
> diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c
> index 4d848a2..a59a892 100644
> --- a/drivers/tty/serial/atmel_serial.c
> +++ b/drivers/tty/serial/atmel_serial.c
> @@ -168,7 +168,6 @@ struct atmel_uart_port {
>         struct circ_buf         rx_ring;
>
>         struct mctrl_gpios      *gpios;
> -       int                     gpio_irq[UART_GPIO_MAX];
>         unsigned int            tx_done_mask;
>         bool                    ms_irq_enabled;
>         bool                    is_usart;       /* usart or uart */
> @@ -499,24 +498,18 @@ static void atmel_enable_ms(struct uart_port *port)
>
>         atmel_port->ms_irq_enabled = true;
>
> -       if (atmel_port->gpio_irq[UART_GPIO_CTS] >= 0)
> -               enable_irq(atmel_port->gpio_irq[UART_GPIO_CTS]);
> -       else
> +       mctrl_gpio_enable_ms(atmel_port->gpios);
> +
> +       if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_CTS))
>                 ier |= ATMEL_US_CTSIC;
>
> -       if (atmel_port->gpio_irq[UART_GPIO_DSR] >= 0)
> -               enable_irq(atmel_port->gpio_irq[UART_GPIO_DSR]);
> -       else
> +       if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_DSR))
>                 ier |= ATMEL_US_DSRIC;
>
> -       if (atmel_port->gpio_irq[UART_GPIO_RI] >= 0)
> -               enable_irq(atmel_port->gpio_irq[UART_GPIO_RI]);
> -       else
> +       if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_RI))
>                 ier |= ATMEL_US_RIIC;
>
> -       if (atmel_port->gpio_irq[UART_GPIO_DCD] >= 0)
> -               enable_irq(atmel_port->gpio_irq[UART_GPIO_DCD]);
> -       else
> +       if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_DCD))
>                 ier |= ATMEL_US_DCDIC;
>
>         UART_PUT_IER(port, ier);
> @@ -538,24 +531,18 @@ static void atmel_disable_ms(struct uart_port *port)
>
>         atmel_port->ms_irq_enabled = false;
>
> -       if (atmel_port->gpio_irq[UART_GPIO_CTS] >= 0)
> -               disable_irq(atmel_port->gpio_irq[UART_GPIO_CTS]);
> -       else
> +       mctrl_gpio_disable_ms(atmel_port->gpios);
> +
> +       if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_CTS))
>                 idr |= ATMEL_US_CTSIC;
>
> -       if (atmel_port->gpio_irq[UART_GPIO_DSR] >= 0)
> -               disable_irq(atmel_port->gpio_irq[UART_GPIO_DSR]);
> -       else
> +       if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_DSR))
>                 idr |= ATMEL_US_DSRIC;
>
> -       if (atmel_port->gpio_irq[UART_GPIO_RI] >= 0)
> -               disable_irq(atmel_port->gpio_irq[UART_GPIO_RI]);
> -       else
> +       if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_RI))
>                 idr |= ATMEL_US_RIIC;
>
> -       if (atmel_port->gpio_irq[UART_GPIO_DCD] >= 0)
> -               disable_irq(atmel_port->gpio_irq[UART_GPIO_DCD]);
> -       else
> +       if (!mctrl_gpio_is_gpio(atmel_port->gpios, UART_GPIO_DCD))
>                 idr |= ATMEL_US_DCDIC;
>
>         UART_PUT_IDR(port, idr);
> @@ -1161,31 +1148,11 @@ atmel_handle_status(struct uart_port *port, unsigned int pending,
>  static irqreturn_t atmel_interrupt(int irq, void *dev_id)
>  {
>         struct uart_port *port = dev_id;
> -       struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
>         unsigned int status, pending, pass_counter = 0;
> -       bool gpio_handled = false;
>
>         do {
>                 status = atmel_get_lines_status(port);
>                 pending = status & UART_GET_IMR(port);
> -               if (!gpio_handled) {
> -                       /*
> -                        * Dealing with GPIO interrupt
> -                        */
> -                       if (irq == atmel_port->gpio_irq[UART_GPIO_CTS])
> -                               pending |= ATMEL_US_CTSIC;
> -
> -                       if (irq == atmel_port->gpio_irq[UART_GPIO_DSR])
> -                               pending |= ATMEL_US_DSRIC;
> -
> -                       if (irq == atmel_port->gpio_irq[UART_GPIO_RI])
> -                               pending |= ATMEL_US_RIIC;
> -
> -                       if (irq == atmel_port->gpio_irq[UART_GPIO_DCD])
> -                               pending |= ATMEL_US_DCDIC;
> -
> -                       gpio_handled = true;
> -               }
>                 if (!pending)
>                         break;
>
> @@ -1665,45 +1632,6 @@ static void atmel_get_ip_name(struct uart_port *port)
>         }
>  }
>
> -static void atmel_free_gpio_irq(struct uart_port *port)
> -{
> -       struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> -       enum mctrl_gpio_idx i;
> -
> -       for (i = 0; i < UART_GPIO_MAX; i++)
> -               if (atmel_port->gpio_irq[i] >= 0)
> -                       free_irq(atmel_port->gpio_irq[i], port);
> -}
> -
> -static int atmel_request_gpio_irq(struct uart_port *port)
> -{
> -       struct atmel_uart_port *atmel_port = to_atmel_uart_port(port);
> -       int *irq = atmel_port->gpio_irq;
> -       enum mctrl_gpio_idx i;
> -       int err = 0;
> -
> -       for (i = 0; (i < UART_GPIO_MAX) && !err; i++) {
> -               if (irq[i] < 0)
> -                       continue;
> -
> -               irq_set_status_flags(irq[i], IRQ_NOAUTOEN);
> -               err = request_irq(irq[i], atmel_interrupt, IRQ_TYPE_EDGE_BOTH,
> -                                 "atmel_serial", port);
> -               if (err)
> -                       dev_err(port->dev, "atmel_startup - Can't get %d irq\n",
> -                               irq[i]);
> -       }
> -
> -       /*
> -        * If something went wrong, rollback.
> -        */
> -       while (err && (--i >= 0))
> -               if (irq[i] >= 0)
> -                       free_irq(irq[i], port);
> -
> -       return err;
> -}
> -
>  /*
>   * Perform initialization and enable port for reception
>   */
> @@ -1735,7 +1663,7 @@ static int atmel_startup(struct uart_port *port)
>         /*
>          * Get the GPIO lines IRQ
>          */
> -       retval = atmel_request_gpio_irq(port);
> +       retval = mctrl_gpio_request_irqs(atmel_port->gpios);
>         if (retval)
>                 goto free_irq;
>
> @@ -1872,7 +1800,7 @@ static void atmel_shutdown(struct uart_port *port)
>          * Free the interrupts
>          */
>         free_irq(port->irq, port);
> -       atmel_free_gpio_irq(port);
> +       mctrl_gpio_free_irqs(atmel_port->gpios);
>
>         atmel_port->ms_irq_enabled = false;
>
> @@ -2501,24 +2429,13 @@ static int atmel_serial_resume(struct platform_device *pdev)
>  #define atmel_serial_resume NULL
>  #endif
>
> -static int atmel_init_gpios(struct atmel_uart_port *p, struct device *dev)
> +static bool atmel_init_gpios(struct atmel_uart_port *p)
>  {
> -       enum mctrl_gpio_idx i;
> -       struct gpio_desc *gpiod;
> -
> -       p->gpios = mctrl_gpio_init(dev, 0);
> +       p->gpios = mctrl_gpio_init_dt(&p->uart, 0);
>         if (IS_ERR_OR_NULL(p->gpios))
> -               return -1;
> +               return false;
>
> -       for (i = 0; i < UART_GPIO_MAX; i++) {
> -               gpiod = mctrl_gpio_to_gpiod(p->gpios, i);
> -               if (gpiod && (gpiod_get_direction(gpiod) == GPIOF_DIR_IN))
> -                       p->gpio_irq[i] = gpiod_to_irq(gpiod);
> -               else
> -                       p->gpio_irq[i] = -EINVAL;
> -       }
> -
> -       return 0;
> +       return true;
>  }
>
>  static int atmel_serial_probe(struct platform_device *pdev)
> @@ -2558,8 +2475,8 @@ static int atmel_serial_probe(struct platform_device *pdev)
>         port->backup_imr = 0;
>         port->uart.line = ret;
>
> -       ret = atmel_init_gpios(port, &pdev->dev);
> -       if (ret < 0)
> +       port->uart.dev = &pdev->dev;
> +       if (!atmel_init_gpios(port))
>                 dev_err(&pdev->dev, "%s",
>                         "Failed to initialize GPIOs. The serial port may not work as expected");
>
> --
> 1.7.11.3
>

It's ok, no regression found in atmel-serial.
Tested on an at91sam9g35, full duplex between 2 serial ports at 57600
(one with CTS/RTS handled by the controller, the other with CTS/RTS
handled via GPIO).

Tested-by: Richard Genoud <richard.genoud@xxxxxxxxx>
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux