Re: [PATCH v2 RESEND 2/3] Documentation: gpio: Add APM X-Gene standby GPIO controller DTS binding

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Wed, Dec 17, 2014 at 6:10 AM, Y Vo <yvo@xxxxxxx> wrote:
> Documentation for APM X-Gene standby GPIO controller DTS binding.
>
> Signed-off-by: Y Vo <yvo@xxxxxxx>
> ---
>  .../devicetree/bindings/gpio/gpio-xgene-sb.txt     | 31 ++++++++++++++++++++++
>  1 file changed, 31 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt
>
> diff --git a/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt b/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt
> new file mode 100644
> index 0000000..3215e4d
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/gpio/gpio-xgene-sb.txt
> @@ -0,0 +1,31 @@
> +APM X-Gene Standby GPIO controller bindings
> +
> +This is a gpio controller in standby domain.
> +
> +There are 20 GPIO pins from 0..21. There is no GPIO_DS14 and GPIO_DS15.
> +Only GPIO_DS8..GPIO_DS13 support interrupt. IRQ mapping 0x28..0x2d.
> +
> +Required properties:
> +- compatible: "apm,xgene-gpio-sb" for X-Gene Standby GPIO controller
> +- reg: Physical base address and size of the controller's registers
> +- #gpio-cells: Should be two.
> +       - first cell is the pin number
> +       - second cell is used to specify the gpio polarity:
> +               0 = active high
> +               1 = active low
> +- gpio-controller: Marks the device node as a GPIO controller.
> +- interrupts: Shall contains the interrupts.

>From the example it seems it must contain exactly 6 interrupts?
Then state this.

> +Example:
> +       sbgpio: sbgpio@17001000 {
> +               compatible = "apm,xgene-gpio-sb";
> +               reg = <0x0 0x17001000 0x0 0x400>;
> +               #gpio-cells = <2>;
> +               gpio-controller;
> +               interrupts =    <0x0 0x28 0x1>,
> +                               <0x0 0x29 0x1>,
> +                               <0x0 0x2a 0x1>,
> +                               <0x0 0x2b 0x1>,
> +                               <0x0 0x2c 0x1>,
> +                               <0x0 0x2d 0x1>;
> +       };

Yours,
Linus Walleij
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html



[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux