On Tue, Dec 16, 2014 at 3:18 AM, Ray Jui <rjui@xxxxxxxxxxxx> wrote:
> This GPIO driver supports all 3 GPIO controllers in the Broadcom Cygnus
> SoC. The 3 GPIO controllers are 1) the ASIU GPIO controller, 2) the
> chipCommonG GPIO controller, and 3) the ALWAYS-ON GPIO controller
>
> Signed-off-by: Ray Jui <rjui@xxxxxxxxxxxx>
> Reviewed-by: Scott Branden <sbranden@xxxxxxxxxxxx>
(Big thanks to Alexandre for doing the major part of the review,
good work with following up so far!)
(...)
> +config GPIO_BCM_CYGNUS
> + bool "Broadcom Cygnus GPIO support"
> + depends on ARCH_BCM_CYGNUS && OF_GPIO
select GPIOLIB_IRQCHIP
See more about this below.
> +++ b/drivers/gpio/gpio-bcm-cygnus.c
> @@ -0,0 +1,607 @@
> +/*
> + * Copyright (C) 2014 Broadcom Corporation
> + *
> + * This program is free software; you can redistribute it and/or
> + * modify it under the terms of the GNU General Public License as
> + * published by the Free Software Foundation version 2.
> + *
> + * This program is distributed "as is" WITHOUT ANY WARRANTY of any
> + * kind, whether express or implied; without even the implied warranty
> + * of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
> + * GNU General Public License for more details.
> + */
> +
> +#include <linux/kernel.h>
> +#include <linux/slab.h>
> +#include <linux/module.h>
> +#include <linux/irq.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/gpio.h>
> +#include <linux/ioport.h>
> +#include <linux/of_device.h>
> +#include <linux/of_irq.h>
> +#include <linux/irqchip/chained_irq.h>
Skip <linux/irq.h> and <linux/irqchip/chained_irq.h>
as these move to the core with GPIOLIB_IRQCHIP
> +#define CYGNUS_GPIO_DATA_IN_OFFSET 0x00
> +#define CYGNUS_GPIO_DATA_OUT_OFFSET 0x04
> +#define CYGNUS_GPIO_OUT_EN_OFFSET 0x08
> +#define CYGNUS_GPIO_IN_TYPE_OFFSET 0x0c
> +#define CYGNUS_GPIO_INT_DE_OFFSET 0x10
> +#define CYGNUS_GPIO_INT_EDGE_OFFSET 0x14
> +#define CYGNUS_GPIO_INT_MSK_OFFSET 0x18
> +#define CYGNUS_GPIO_INT_STAT_OFFSET 0x1c
> +#define CYGNUS_GPIO_INT_MSTAT_OFFSET 0x20
> +#define CYGNUS_GPIO_INT_CLR_OFFSET 0x24
> +#define CYGNUS_GPIO_PAD_RES_OFFSET 0x34
> +#define CYGNUS_GPIO_RES_EN_OFFSET 0x38
> +
> +/* drive strength control for ASIU GPIO */
> +#define CYGNUS_GPIO_ASIU_DRV0_CTRL_OFFSET 0x58
> +
> +/* drive strength control for CCM GPIO */
> +#define CYGNUS_GPIO_CCM_DRV0_CTRL_OFFSET 0x00
This stuff (drive strength) is pin control, pin config.
It does not belong in a pure GPIO driver. If you're
making a combined pin control + GPIO driver, it
shall be put in drivers/pinctrl/*
> +#define GPIO_BANK_SIZE 0x200
> +#define NGPIOS_PER_BANK 32
> +#define GPIO_BANK(pin) ((pin) / NGPIOS_PER_BANK)
> +
> +#define CYGNUS_GPIO_REG(pin, reg) (GPIO_BANK(pin) * GPIO_BANK_SIZE + (reg))
> +#define CYGNUS_GPIO_SHIFT(pin) ((pin) % NGPIOS_PER_BANK)
> +
> +#define GPIO_FLAG_BIT_MASK 0xffff
> +#define GPIO_PULL_BIT_SHIFT 16
> +#define GPIO_PULL_BIT_MASK 0x3
> +
> +#define GPIO_DRV_STRENGTH_BIT_SHIFT 20
> +#define GPIO_DRV_STRENGTH_BITS 3
> +#define GPIO_DRV_STRENGTH_BIT_MASK ((1 << GPIO_DRV_STRENGTH_BITS) - 1)
> +
> +/*
> + * For GPIO internal pull up/down registers
> + */
> +enum gpio_pull {
> + GPIO_PULL_NONE = 0,
> + GPIO_PULL_UP,
> + GPIO_PULL_DOWN,
> + GPIO_PULL_INVALID,
> +};
> +
> +/*
> + * GPIO drive strength
> + */
> +enum gpio_drv_strength {
> + GPIO_DRV_STRENGTH_2MA = 0,
> + GPIO_DRV_STRENGTH_4MA,
> + GPIO_DRV_STRENGTH_6MA,
> + GPIO_DRV_STRENGTH_8MA,
> + GPIO_DRV_STRENGTH_10MA,
> + GPIO_DRV_STRENGTH_12MA,
> + GPIO_DRV_STRENGTH_14MA,
> + GPIO_DRV_STRENGTH_16MA,
> + GPIO_DRV_STRENGTH_INVALID,
> +};
All this pull up/down and drive strength is pin config for
the pin control subsystem.
> +struct cygnus_gpio {
> + struct device *dev;
> + void __iomem *base;
> + void __iomem *io_ctrl;
> + spinlock_t lock;
> + struct gpio_chip gc;
> + unsigned num_banks;
> + int irq;
> + struct irq_domain *irq_domain;
Skip irq and irqdomain and use GPIOLIB_IRQCHIP
> +static u32 cygnus_readl(struct cygnus_gpio *cygnus_gpio, unsigned int offset)
> +{
> + return readl(cygnus_gpio->base + offset);
> +}
> +
> +static void cygnus_writel(struct cygnus_gpio *cygnus_gpio,
> + unsigned int offset, u32 val)
> +{
> + writel(val, cygnus_gpio->base + offset);
> +}
I don't see the value of using these accessors over just inlining
your readl/writel stuff.
(...)
> +static int cygnus_gpio_to_irq(struct gpio_chip *gc, unsigned offset)
> +{
> + struct cygnus_gpio *cygnus_gpio = to_cygnus_gpio(gc);
> +
> + return irq_find_mapping(cygnus_gpio->irq_domain, offset);
> +}
This goes away to the core with GPIOLIB_IRQCHIP
> +static void cygnus_gpio_irq_handler(unsigned int irq, struct irq_desc *desc)
> +{
> + struct cygnus_gpio *cygnus_gpio;
> + struct irq_chip *chip = irq_desc_get_chip(desc);
> + int i, bit;
> +
> + chained_irq_enter(chip, desc);
> +
> + cygnus_gpio = irq_get_handler_data(irq);
> +
> + /* go through the entire GPIO banks and handle all interrupts */
> + for (i = 0; i < cygnus_gpio->num_banks; i++) {
> + unsigned long val = cygnus_readl(cygnus_gpio,
> + (i * GPIO_BANK_SIZE) +
> + CYGNUS_GPIO_INT_MSTAT_OFFSET);
> +
> + for_each_set_bit(bit, &val, NGPIOS_PER_BANK) {
> + unsigned pin = NGPIOS_PER_BANK * i + bit;
> + int child_irq =
> + cygnus_gpio_to_irq(&cygnus_gpio->gc, pin);
> +
> + /*
> + * Clear the interrupt before invoking the
> + * handler, so we do not leave any window
> + */
> + cygnus_writel(cygnus_gpio, (i * GPIO_BANK_SIZE) +
> + CYGNUS_GPIO_INT_CLR_OFFSET, BIT(bit));
> +
> + generic_handle_irq(child_irq);
> + }
> + }
> +
> + chained_irq_exit(chip, desc);
> +}
Looks good, but you will need to have the struct gpio_chip * as
handler data to use GPIOLIB_IRQCHIP, so get from there to
the struct cygnus_gpio something like:
struct gpio_chip *gc = irq_desc_get_handler_data(desc);
struct cygnus_gpio *cyg = to_cygnus_gpio(gc);
> +static int cygnus_gpio_get(struct gpio_chip *gc, unsigned gpio)
> +{
> + struct cygnus_gpio *cygnus_gpio = to_cygnus_gpio(gc);
> + unsigned int offset = CYGNUS_GPIO_REG(gpio,
> + CYGNUS_GPIO_DATA_IN_OFFSET);
> + unsigned int shift = CYGNUS_GPIO_SHIFT(gpio);
> + u32 val;
> +
> + val = cygnus_readl(cygnus_gpio, offset);
> + val = (val >> shift) & 1;
No, do this:
return !!(cygnus_readl(cygnus_gpio, offset) & BIT(shift));
Maybe rename the "shift" variable to "bit" or just use the macro
directly in the readl().
> +static int cygnus_gpio_irq_map(struct irq_domain *d, unsigned int irq,
> + irq_hw_number_t hwirq)
> +{
> + int ret;
> +
> + ret = irq_set_chip_data(irq, d->host_data);
> + if (ret < 0)
> + return ret;
> + irq_set_lockdep_class(irq, &gpio_lock_class);
> + irq_set_chip_and_handler(irq, &cygnus_gpio_irq_chip,
> + handle_simple_irq);
> + set_irq_flags(irq, IRQF_VALID);
> +
> + return 0;
> +}
> +
> +static void cygnus_gpio_irq_unmap(struct irq_domain *d, unsigned int irq)
> +{
> + irq_set_chip_and_handler(irq, NULL, NULL);
> + irq_set_chip_data(irq, NULL);
> +}
> +
> +static struct irq_domain_ops cygnus_irq_ops = {
> + .map = cygnus_gpio_irq_map,
> + .unmap = cygnus_gpio_irq_unmap,
> + .xlate = irq_domain_xlate_twocell,
> +};
All this goes away with GPIOLIB_IRQCHIP (that is what is good about it).
> +#ifdef CONFIG_OF_GPIO
What, that should be defined all the time, you depend on it in
Kconfig!
> +static void cygnus_gpio_set_pull(struct cygnus_gpio *cygnus_gpio,
> + unsigned gpio, enum gpio_pull pull)
(...)
> +static void cygnus_gpio_set_strength(struct cygnus_gpio *cygnus_gpio,
> + unsigned gpio, enum gpio_drv_strength strength)
(...)
> +static int cygnus_gpio_of_xlate(struct gpio_chip *gc,
> + const struct of_phandle_args *gpiospec, u32 *flags)
NAK. This is pin control, put this in the pin control driver.
I guess the same that is part of this patch series.
(...)
> +static int cygnus_gpio_probe(struct platform_device *pdev)
> +{
> + struct device *dev = &pdev->dev;
> + struct resource *res;
> + struct cygnus_gpio *cygnus_gpio;
> + struct gpio_chip *gc;
> + u32 i, ngpios;
> + int ret;
> +
> + cygnus_gpio = devm_kzalloc(dev, sizeof(*cygnus_gpio), GFP_KERNEL);
> + if (!cygnus_gpio)
> + return -ENOMEM;
> +
> + cygnus_gpio->dev = dev;
> + platform_set_drvdata(pdev, cygnus_gpio);
> +
> + if (of_property_read_u32(dev->of_node, "ngpios", &ngpios)) {
> + dev_err(&pdev->dev, "missing ngpios DT property\n");
> + return -ENODEV;
> + }
> + cygnus_gpio->num_banks = (ngpios + NGPIOS_PER_BANK - 1) /
> + NGPIOS_PER_BANK;
> +
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
> + cygnus_gpio->base = devm_ioremap_resource(dev, res);
> + if (IS_ERR(cygnus_gpio->base)) {
> + dev_err(&pdev->dev, "unable to map I/O memory\n");
> + return PTR_ERR(cygnus_gpio->base);
> + }
> +
> + /*
> + * Only certain types of Cygnus GPIO interfaces have I/O control
> + * registers
> + */
> + res = platform_get_resource(pdev, IORESOURCE_MEM, 1);
> + if (res) {
> + cygnus_gpio->io_ctrl = devm_ioremap_resource(dev, res);
> + if (IS_ERR(cygnus_gpio->io_ctrl)) {
> + dev_err(&pdev->dev, "unable to map I/O memory\n");
> + return PTR_ERR(cygnus_gpio->io_ctrl);
> + }
> + }
This is a good indication that it's a separate piece of HW and should
be a separate pin control driver.
> +
> + spin_lock_init(&cygnus_gpio->lock);
> +
> + gc = &cygnus_gpio->gc;
> + gc->base = -1;
> + gc->ngpio = ngpios;
> + gc->label = dev_name(dev);
> + gc->dev = dev;
> +#ifdef CONFIG_OF_GPIO
You depend on this symbol.
> + gc->of_node = dev->of_node;
> + gc->of_gpio_n_cells = 2;
> + gc->of_xlate = cygnus_gpio_of_xlate;
> +#endif
> + gc->direction_input = cygnus_gpio_direction_input;
> + gc->direction_output = cygnus_gpio_direction_output;
> + gc->set = cygnus_gpio_set;
> + gc->get = cygnus_gpio_get;
> + gc->to_irq = cygnus_gpio_to_irq;
> +
> + ret = gpiochip_add(gc);
> + if (ret < 0) {
> + dev_err(&pdev->dev, "unable to add GPIO chip\n");
> + return ret;
> + }
> +
> + /*
> + * Some of the GPIO interfaces do not have interrupt wired to the main
> + * processor
> + */
> + cygnus_gpio->irq = platform_get_irq(pdev, 0);
> + if (cygnus_gpio->irq < 0) {
> + ret = cygnus_gpio->irq;
> + if (ret == -EPROBE_DEFER)
> + goto err_rm_gpiochip;
> +
> + dev_info(&pdev->dev, "no interrupt hook\n");
> + }
>From here:
> + cygnus_gpio->irq_domain = irq_domain_add_linear(dev->of_node,
> + gc->ngpio, &cygnus_irq_ops, cygnus_gpio);
> + if (!cygnus_gpio->irq_domain) {
> + dev_err(&pdev->dev, "unable to allocate IRQ domain\n");
> + ret = -ENXIO;
> + goto err_rm_gpiochip;
> + }
> +
> + for (i = 0; i < gc->ngpio; i++) {
> + int irq = irq_create_mapping(cygnus_gpio->irq_domain, i);
> +
> + irq_set_lockdep_class(irq, &gpio_lock_class);
> + irq_set_chip_data(irq, cygnus_gpio);
> + irq_set_chip_and_handler(irq, &cygnus_gpio_irq_chip,
> + handle_simple_irq);
> + set_irq_flags(irq, IRQF_VALID);
> + }
> +
> + irq_set_chained_handler(cygnus_gpio->irq, cygnus_gpio_irq_handler);
> + irq_set_handler_data(cygnus_gpio->irq, cygnus_gpio);
To here, replace with a single call to
gpiochip_set_chained_irqchip(chip *, irq_chip *, irq, handler)...
Look at other drivers using GPIOLIB_IRQCHIP for inspiration.
Yours,
Linus Walleij
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
Re: [PATCH v6 2/3] gpio: Cygnus: add GPIO driver
[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]
- Subject: Re: [PATCH v6 2/3] gpio: Cygnus: add GPIO driver
- From: Linus Walleij <linus.walleij@xxxxxxxxxx>
- Date: Tue, 13 Jan 2015 09:53:12 +0100
- In-reply-to: <1418696307-19392-3-git-send-email-rjui@broadcom.com>
- Follow-Ups:
- Re: [PATCH v6 2/3] gpio: Cygnus: add GPIO driver
- From: Ray Jui
- Re: [PATCH v6 2/3] gpio: Cygnus: add GPIO driver
- References:
- [PATCH v6 0/3] Add gpio support to Broadcom Cygnus SoC
- From: Ray Jui
- [PATCH v6 2/3] gpio: Cygnus: add GPIO driver
- From: Ray Jui
- [PATCH v6 0/3] Add gpio support to Broadcom Cygnus SoC
- Prev by Date: Re: [RFC PATCH v2 2/4] serial: mxs-auart: Use helpers for gpio irqs
- Next by Date: Re: [PATCH] pinctrl: consumer: use correct retval for placeholder functions
- Previous by thread: [PATCH v6 2/3] gpio: Cygnus: add GPIO driver
- Next by thread: Re: [PATCH v6 2/3] gpio: Cygnus: add GPIO driver
- Index(es):
 |