Re: [RFC PATCH 1/2] pinctrl: Add output-disable

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Linus,

On Fri, Oct 31, 2014 at 1:49 AM, Linus Walleij <linus.walleij@xxxxxxxxxx> wrote:
> On Tue, Oct 28, 2014 at 9:57 PM, Doug Anderson <dianders@xxxxxxxxxxxx> wrote:
>> The pinctrl bindings / API allow you to specify that:
>> - a pin should be an output
>> - a pin should have its input path enabled / disabled
>>
>> ...but they don't allow you to tell a pin to stop outputting.  Lets
>> add a new setting for that just in case the bootloader (or the default
>> state) left a pin as an output and we don't want it that way anymore.
>>
>> Signed-off-by: Doug Anderson <dianders@xxxxxxxxxxxx>
> (...)
>> + * @PIN_CONFIG_OUTPUT_DISABLE: this will configure the pin _not_ to output.
>> + *     Parameter should be 1.
>
> This doesn't make sense. The pin is either low, high, some analog mode
> or tristate/high impedance.
>
> It does *not* stop existing.
>
> Figure out the exact electronic meaning of what happens when you do
> "output disable" in your hardware, I think it is very likely that
> PIN_CONFIG_BIAS_HIGH_IMPEDANCE is what you are really
> after here.

OK, that seems plausible.  ...so it is OK to set both
"bias-high-impedance" _and_ "bias-pull-up" on a pin?  That seemed
weird to me but if that's right I can do that and try to implement
"bias-high-impedance" on Rockchip...


Maybe better to explain the problem.  I have a pin that I wish to
drive high weakly (using a pullup rather than actually pushing
output-high to the pin).  The firmware has left the pin configured as
an output with no pull.

I can configure the pin like this:
  rockchip,pins = <7 12 RK_FUNC_GPIO &pcfg_pull_up>;

  pcfg_pull_up: pcfg-pull-up {
    bias-pull-up;
  };

When I do this the current Rockchip pinctrl driver will _not_
configure me as an input.  It will happily flip the "pullup" bit in
hardware and leave the pin configured as an output.

I could certainly reach into the GPIO controller part of things
whenever I see "bias-pull-up" and configure the pin as an input.  I
guess that wouldn't actually hurt to do even if the pin wasn't
configured as a GPIO...  In other words, if someone has:
  rockchip,pins = <6 22 RK_FUNC_1 &pcfg_pull_up>;

...it doesn't hurt to set the GPIO controller for this pin to be an
input because it's not used when RK_FUNC_1 is used.


A third option that would work in my case (and actually be sorta
clean) would be to implement a faux open-drain output.  The hardware
itself doesn't have a concept of open drain (unlike some SoCs) but I
could implement it by swapping between "input pulled up" and "output
driven low".


-Doug
--
To unsubscribe from this list: send the line "unsubscribe linux-gpio" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at  http://vger.kernel.org/majordomo-info.html




[Index of Archives]     [Linux SPI]     [Linux Kernel]     [Linux ARM (vger)]     [Linux ARM MSM]     [Linux Omap]     [Linux Arm]     [Linux Tegra]     [Fedora ARM]     [Linux for Samsung SOC]     [eCos]     [Linux Fastboot]     [Gcc Help]     [Git]     [DCCP]     [IETF Announce]     [Security]     [Linux MIPS]     [Yosemite Campsites]

  Powered by Linux