On Fri, Sep 26, 2014 at 1:07 PM, Chang Rebecca Swee Fun <rebecca.swee.fun.chang@xxxxxxxxx> wrote: > Intel Quark X1000 provides a total of 16 GPIOs. The GPIOs are split between > the legacy I/O bridge and the GPIO controller. > > GPIO-SCH is the GPIO pins on legacy bridge for Intel Quark SoC. > Intel Quark X1000 has 2 GPIOs powered by the core power well and 6 from > the suspend power well. > > This piece of work is derived from Dan O'Donovan's initial work for Quark > X1000 enabling. > > Signed-off-by: Chang Rebecca Swee Fun <rebecca.swee.fun.chang@xxxxxxxxx> > --- > drivers/gpio/Kconfig | 11 +++++++++-- > drivers/gpio/gpio-sch.c | 6 ++++++ > 2 files changed, 15 insertions(+), 2 deletions(-) > > diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig > index 690904a..64683a9 100644 > --- a/drivers/gpio/Kconfig > +++ b/drivers/gpio/Kconfig > @@ -356,25 +356,32 @@ config GPIO_VR41XX > Say yes here to support the NEC VR4100 series General-purpose I/O Uint > > config GPIO_SCH > - tristate "Intel SCH/TunnelCreek/Centerton GPIO" > + tristate "Intel SCH/TunnelCreek/Centerton/Quark X1000 GPIO" Do we need 'X1000' here right now? > depends on PCI && X86 > select MFD_CORE > select LPC_SCH > help > Say yes here to support GPIO interface on Intel Poulsbo SCH, > - Intel Tunnel Creek processor or Intel Centerton processor. > + Intel Tunnel Creek processor, Intel Centerton processor or I think you may use comma before 'or' word. > + Intel Quark X1000 SoC. > + > The Intel SCH contains a total of 14 GPIO pins. Ten GPIOs are > powered by the core power rail and are turned off during sleep > modes (S3 and higher). The remaining four GPIOs are powered by > the Intel SCH suspend power supply. These GPIOs remain > active during S3. The suspend powered GPIOs can be used to wake the > system from the Suspend-to-RAM state. > + > The Intel Tunnel Creek processor has 5 GPIOs powered by the > core power rail and 9 from suspend power supply. > + > The Intel Centerton processor has a total of 30 GPIO pins. > Twenty-one are powered by the core power rail and 9 from the > suspend power supply. > > + The Intel Quark X1000 SoC has 2 GPIOs powered by the core > + power well and 6 from the suspend power well. > + > config GPIO_ICH > tristate "Intel ICH GPIO" > depends on PCI && X86 > diff --git a/drivers/gpio/gpio-sch.c b/drivers/gpio/gpio-sch.c > index 6e89be9..952990f 100644 > --- a/drivers/gpio/gpio-sch.c > +++ b/drivers/gpio/gpio-sch.c > @@ -241,6 +241,12 @@ static int sch_gpio_probe(struct platform_device *pdev) > sch->chip.ngpio = 30; > break; > > + case PCI_DEVICE_ID_INTEL_QUARK_X1000_ILB: > + sch->core_base = 0; > + sch->resume_base = 2; > + sch->chip.ngpio = 8; > + break; > + > default: > return -ENODEV; > } > -- > 1.7.9.5 > > -- > To unsubscribe from this list: send the line "unsubscribe linux-kernel" in > the body of a message to majordomo@xxxxxxxxxxxxxxx > More majordomo info at http://vger.kernel.org/majordomo-info.html > Please read the FAQ at http://www.tux.org/lkml/ -- With Best Regards, Andy Shevchenko -- To unsubscribe from this list: send the line "unsubscribe linux-gpio" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html