Document the SelectMAP interface of Xilinx 7 series FPGA. Signed-off-by: Charles Perry <charles.perry@xxxxxxxxxxxxxxxxxxxx> --- Changes since v4: (from Yilun and Krzysztof review) * dt-bindings: remove usage of "_b" and "-b" for the new driver. We agreed that the spi and selectmap driver will use different bindings which will be handled by the driver core and that the legacy names will be used only for the spi compatible. .../bindings/fpga/xlnx,fpga-selectmap.yaml | 86 +++++++++++++++++++ 1 file changed, 86 insertions(+) create mode 100644 Documentation/devicetree/bindings/fpga/xlnx,fpga-selectmap.yaml diff --git a/Documentation/devicetree/bindings/fpga/xlnx,fpga-selectmap.yaml b/Documentation/devicetree/bindings/fpga/xlnx,fpga-selectmap.yaml new file mode 100644 index 0000000000000..05775746fd706 --- /dev/null +++ b/Documentation/devicetree/bindings/fpga/xlnx,fpga-selectmap.yaml @@ -0,0 +1,86 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/fpga/xlnx,fpga-selectmap.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Xilinx SelectMAP FPGA interface + +maintainers: + - Charles Perry <charles.perry@xxxxxxxxxxxxxxxxxxxx> + +description: | + Xilinx 7 Series FPGAs support a method of loading the bitstream over a + parallel port named the SelectMAP interface in the documentation. Only + the x8 mode is supported where data is loaded at one byte per rising edge of + the clock, with the MSB of each byte presented to the D0 pin. + + Datasheets: + https://www.xilinx.com/support/documentation/user_guides/ug470_7Series_Config.pdf + +allOf: + - $ref: /schemas/memory-controllers/mc-peripheral-props.yaml# + +properties: + compatible: + enum: + - xlnx,fpga-xc7s-selectmap + - xlnx,fpga-xc7a-selectmap + - xlnx,fpga-xc7k-selectmap + - xlnx,fpga-xc7v-selectmap + + reg: + description: + At least 1 byte of memory mapped IO + maxItems: 1 + + prog-gpios: + description: + config pin (referred to as PROGRAM_B in the manual) + maxItems: 1 + + done-gpios: + description: + config status pin (referred to as DONE in the manual) + maxItems: 1 + + init-gpios: + description: + initialization status and configuration error pin + (referred to as INIT_B in the manual) + maxItems: 1 + + csi-gpios: + description: + chip select pin (referred to as CSI_B in the manual) + Optional gpio for if the bus controller does not provide a chip select. + maxItems: 1 + + rdwr-gpios: + description: + read/write select pin (referred to as RDWR_B in the manual) + Optional gpio for if the bus controller does not provide this pin. + maxItems: 1 + +required: + - compatible + - reg + - prog-gpios + - done-gpios + - init-gpios + +unevaluatedProperties: false + +examples: + - | + #include <dt-bindings/gpio/gpio.h> + fpga-mgr@8000000 { + compatible = "xlnx,fpga-xc7s-selectmap"; + reg = <0x8000000 0x4>; + prog-gpios = <&gpio5 5 GPIO_ACTIVE_LOW>; + init-gpios = <&gpio5 8 GPIO_ACTIVE_LOW>; + done-gpios = <&gpio2 30 GPIO_ACTIVE_HIGH>; + csi-gpios = <&gpio3 19 GPIO_ACTIVE_LOW>; + rdwr-gpios = <&gpio3 10 GPIO_ACTIVE_LOW>; + }; +... -- 2.43.0
