Re: [PATCH 2/3] hwmon: Support ADI Fan Control IP

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Mon, 2019-10-07 at 07:18 -0700, Guenter Roeck wrote:

> 
> On 10/7/19 6:52 AM, Sa, Nuno wrote:
> [ ... ]
> > > > +static long axi_fan_control_get_pwm_duty(const struct
> > > > axi_fan_control_data *ctl)
> > > > +{
> > > > +	u32 pwm_width =
> > > > axi_fan_control_ioread(ADI_REG_PWM_WIDTH, ctl);
> > > > +	u32 pwm_period =
> > > > axi_fan_control_ioread(ADI_REG_PWM_PERIOD,
> > > > ctl);
> > > > +
> > > > +	return DIV_ROUND_CLOSEST(pwm_width * SYSFS_PWM_MAX,
> > > > pwm_period);
> > > 
> > > Is pwm_period guaranteed to be != 0 ?
> > 
> > Yes, It is a RO register and it is set by the core with the default
> > of
> > 0x4e20.
> 
> Trusting the hardware doesn't make me too comfortable. Are we sure at
> all
> times that the HW isn't messed up ? If so, please at least add a
> comment
> stating that the HW will never return 0. We can then fix it after we
> get
> the first crash report from the field ;-).

Will do that.

> [ ... ]
> 
> > > > +	if (irq_pending & ADI_IRQ_SRC_TEMP_INCREASE)
> > > > +		/* hardware requested a new pwm */
> > > > +		ctl->hw_pwm_req = true;
> > > > +
> > > I don't really understand the logic here. If
> > > ADI_IRQ_SRC_TEMP_INCREASE means
> > > that hardware wants a new pwm, how is userspace informed about
> > > that
> > > request ?
> > 
> > It isn't. Userspace would have to read the pwm attribute and figure
> > that changed. Should I use something like sysfs_notify() on the pwm
> > attribute?
> > 
> That might make sense.
> 
> > > And why are the tacho paramaters _not_ updated in this case later
> > > on
> > > (unless
> > > ADI_IRQ_SRC_PWM_CHANGED and ADI_IRQ_SRC_TEMP_INCREASE are both
> > > set) ?
> > > It might be useful to describe the expected sequence of events.
> > 
> > The core can change the PWM by itself (which is when we receive
> > ADI_IRQ_SRC_TEMP_INCREASE) and in that case it will use predefined
> > values to evaluate the tacho signal (so it won't use the values on
> > TACH_PERIOD and TACH_TOLERANCE). Alternatively, the user can
> > request a
> > new PWM by writing the pwm attribute. In this case the CORE is
> > expecting that TACH_PERIOD and TACH_TOLERANCE are given otherwise
> > it
> > won't evaluate the tacho signal. Note that when is the user which
> > requests a new pwm we only get ADI_IRQ_SRC_PWM_CHANGED (and not +	
> > if (irq_pending & ADI_IRQ_SRC_TEMP_INCREASE), so I use that to know
> > when do I have to update the tacho parameters.
> >   
> Wondering ... if setting the pwm requires an update of period and
> tolerance,
> why not set update_tacho_params to true when the pwm value is
> written, or
> update the registers directly instead of waiting for an interrupt ?

After requesting a new duty-cycle there is 5s delay on which the core
waits for the fan rotation speed to stabilize. Only after that, we have
to provide the tach parameters. Also note that we do need to use the
updated tach measurement value to derive this parameters. So, we need
to wait for the ADI_IRQ_SRC_NEW_MEASUR interrupt.

> Either case, I think the above sequence of events should be explained
> in the driver for future developers to understand why the code is
> written
> the way it is.

will do that.

> > )
> > 
> > > > +	if (irq_pending & ADI_IRQ_SRC_TACH_ERR)
> > > > +		ctl->fan_fault = 1;
> > > 
> > > Is it on purpose that this bit is never reset ?
> > 
> > Yes, and it is wrong. I though that the core would never clear this
> > alarm but it does clear it in the next temperature reading cycle
> > (and
> > set it again if needed). Then, would a clear on read be a correct
> > approach?
> 
> Not sure if there is a "correct", but I think it would make sense.
> 
> > > > +
> > > > +	/* clear all interrupts */
> > > > +	clear_mask = irq_pending & ADI_IRQ_SRC_MASK;
> > > > +	axi_fan_control_iowrite(clear_mask,
> > > > ADI_REG_IRQ_PENDING, ctl);
> > > > +
> > > > +	return IRQ_HANDLED;
> > > > +}
> > > > +
> > > > +static int axi_fan_control_init(struct axi_fan_control_data
> > > > *ctl,
> > > > +				const struct device_node *np)
> > > > +{
> > > > +	int ret;
> > > > +
> > > > +	/* get fan pulses per revolution */
> > > > +	ret = of_property_read_u32(np, "adi,pulses-per-
> > > > revolution",
> > > > &ctl->ppr);
> > > > +	if (ret)
> > > > +		return ret;
> > > 
> > > So all random values are acceptable, including 0 and 0xffffffff ?
> > 
> > Yes, I'm aware that 1 and 2 are typical values but I'm not sure
> > what is
> > the maximum that typically exists so I didn't want to put limits
> > here
> > without knowing. Though at least 0 must not be accepted since then
> > we
> > are always dividing by 0 when reading the FAN rpm.
> > 
> The only values I am aware of are 2 and 4. I don't recall seeing any
> fans
> with 1 pulse per revolution. Overall, I don't think values other than
> 1, 2,
> and 4 make sense.

 Will use 1,2 and 4 and update dt bindings accordingly.

> Guenter





[Index of Archives]     [LM Sensors]     [Linux Sound]     [ALSA Users]     [ALSA Devel]     [Linux Audio Users]     [Linux Media]     [Kernel]     [Gimp]     [Yosemite News]     [Linux Media]

  Powered by Linux