Instead of using a custom binding for retrieving the GPIO that activates the
LCD from devicetree, use a standard regulator.
This approach has the advantage to be more generic.
For example: in the case of a board that has a PMIC supplying the LCD voltage,
the current approach would not work, as it only searches for a GPIO pin.
Signed-off-by: Fabio Estevam <fabio.estevam@xxxxxxxxxxxxx>
---
Chages since v4:
- Merged the 2 previous patches into one in order not to break keep mxsfb functionality
- Remove unneeded change in mxsfb.txt
- Use regulator_disable to pair with regulator_enable
Changes since v3:
- None
Changes since v2:
- Use devm_regulator_get()
Changes since v1:
- No changes
Documentation/devicetree/bindings/fb/mxsfb.txt | 2 --
arch/arm/boot/dts/imx23-evk.dts | 11 ++++++-
arch/arm/boot/dts/imx28-evk.dts | 11 ++++++-
drivers/video/mxsfb.c | 41 +++++++++++++-----------
4 files changed, 43 insertions(+), 22 deletions(-)
diff --git a/Documentation/devicetree/bindings/fb/mxsfb.txt b/Documentation/devicetree/bindings/fb/mxsfb.txt
index 7ba3b76..5d810eb 100644
--- a/Documentation/devicetree/bindings/fb/mxsfb.txt
+++ b/Documentation/devicetree/bindings/fb/mxsfb.txt
@@ -8,7 +8,6 @@ Required properties:
- display : phandle to display node (see below for details)
Optional properties:
-- panel-enable-gpios : Should specify the gpio for panel enable
* display node
@@ -25,7 +24,6 @@ lcdif@80030000 {
compatible = "fsl,imx28-lcdif";
reg = <0x80030000 2000>;
interrupts = <38 86>;
- panel-enable-gpios = <&gpio3 30 0>;
display: display {
bits-per-pixel = <32>;
diff --git a/arch/arm/boot/dts/imx23-evk.dts b/arch/arm/boot/dts/imx23-evk.dts
index 7880e17..da0588a 100644
--- a/arch/arm/boot/dts/imx23-evk.dts
+++ b/arch/arm/boot/dts/imx23-evk.dts
@@ -59,7 +59,7 @@
lcdif@80030000 {
pinctrl-names = "default";
pinctrl-0 = <&lcdif_24bit_pins_a>;
- panel-enable-gpios = <&gpio1 18 0>;
+ lcd-supply = <®_lcd_3v3>;
display = <&display>;
status = "okay";
@@ -120,6 +120,15 @@
regulator-max-microvolt = <3300000>;
gpio = <&gpio1 29 0>;
};
+
+ reg_lcd_3v3: lcd-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio1 18 0>;
+ enable-active-high;
+ };
};
backlight {
diff --git a/arch/arm/boot/dts/imx28-evk.dts b/arch/arm/boot/dts/imx28-evk.dts
index 2d4ea3b..3637bf3 100644
--- a/arch/arm/boot/dts/imx28-evk.dts
+++ b/arch/arm/boot/dts/imx28-evk.dts
@@ -123,7 +123,7 @@
pinctrl-names = "default";
pinctrl-0 = <&lcdif_24bit_pins_a
&lcdif_pins_evk>;
- panel-enable-gpios = <&gpio3 30 0>;
+ lcd-supply = <®_lcd_3v3>;
display = <&display>;
status = "okay";
@@ -310,6 +310,15 @@
gpio = <&gpio3 8 0>;
enable-active-high;
};
+
+ reg_lcd_3v3: lcd-3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "lcd-3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ gpio = <&gpio3 30 0>;
+ enable-active-high;
+ };
};
sound {
diff --git a/drivers/video/mxsfb.c b/drivers/video/mxsfb.c
index eac7c1a..74fbfd1 100644
--- a/drivers/video/mxsfb.c
+++ b/drivers/video/mxsfb.c
@@ -42,7 +42,6 @@
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/of_device.h>
-#include <linux/of_gpio.h>
#include <video/of_display_timing.h>
#include <linux/platform_device.h>
#include <linux/clk.h>
@@ -50,6 +49,7 @@
#include <linux/io.h>
#include <linux/pinctrl/consumer.h>
#include <linux/fb.h>
+#include <linux/regulator/consumer.h>
#include <video/videomode.h>
#define REG_SET 4
@@ -179,6 +179,7 @@ struct mxsfb_info {
unsigned dotclk_delay;
const struct mxsfb_devdata *devdata;
u32 sync;
+ struct regulator *reg_lcd;
};
#define mxsfb_is_v3(host) (host->devdata->ipversion == 3)
@@ -338,9 +339,19 @@ static void mxsfb_enable_controller(struct fb_info *fb_info)
{
struct mxsfb_info *host = to_imxfb_host(fb_info);
u32 reg;
+ int ret;
dev_dbg(&host->pdev->dev, "%s\n", __func__);
+ if (!IS_ERR(host->reg_lcd)) {
+ ret = regulator_enable(host->reg_lcd);
+ if (ret) {
+ dev_err(&host->pdev->dev,
+ "lcd regulator enable failed: %d\n", ret);
+ return;
+ }
+ }
+
clk_prepare_enable(host->clk);
clk_set_rate(host->clk, PICOS2KHZ(fb_info->var.pixclock) * 1000U);
@@ -362,9 +373,19 @@ static void mxsfb_disable_controller(struct fb_info *fb_info)
struct mxsfb_info *host = to_imxfb_host(fb_info);
unsigned loop;
u32 reg;
+ int ret;
dev_dbg(&host->pdev->dev, "%s\n", __func__);
+ if (!IS_ERR(host->reg_lcd)) {
+ ret = regulator_disable(host->reg_lcd);
+ if (ret) {
+ dev_err(&host->pdev->dev,
+ "lcd regulator disable failed: %d\n", ret);
+ return;
+ }
+ }
+
/*
* Even if we disable the controller here, it will still continue
* until its FIFOs are running out of data
@@ -859,8 +880,6 @@ static int mxsfb_probe(struct platform_device *pdev)
struct fb_info *fb_info;
struct fb_modelist *modelist;
struct pinctrl *pinctrl;
- int panel_enable;
- enum of_gpio_flags flags;
int ret;
if (of_id)
@@ -904,21 +923,7 @@ static int mxsfb_probe(struct platform_device *pdev)
goto fb_release;
}
- panel_enable = of_get_named_gpio_flags(pdev->dev.of_node,
- "panel-enable-gpios", 0, &flags);
- if (gpio_is_valid(panel_enable)) {
- unsigned long f = GPIOF_OUT_INIT_HIGH;
- if (flags == OF_GPIO_ACTIVE_LOW)
- f = GPIOF_OUT_INIT_LOW;
- ret = devm_gpio_request_one(&pdev->dev, panel_enable,
- f, "panel-enable");
- if (ret) {
- dev_err(&pdev->dev,
- "failed to request gpio %d: %d\n",
- panel_enable, ret);
- goto fb_release;
- }
- }
+ host->reg_lcd = devm_regulator_get(&pdev->dev, "lcd");
fb_info->pseudo_palette = devm_kzalloc(&pdev->dev, sizeof(u32) * 16,
GFP_KERNEL);
--
1.7.9.5
--
To unsubscribe from this list: send the line "unsubscribe linux-fbdev" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
