Hi,
On Wednesday 18 January 2012 07:33 AM, Donghwa Lee wrote:
> Samsung S5PC210 and EXYNOS SoC platform has MIPI-DSI controller and MIPI-DSI
> based LCD Panel could be used with it. This patch supports MIPI-DSI driver
> based Samsung SoC chip.
>
> LCD panel driver based MIPI-DSI should be registered to MIPI-DSI driver at
> machine code and LCD panel driver specific function registered to mipi_dsim_ddi
> structure at lcd panel init function called system init.
> In the MIPI-DSI driver, find lcd panel driver by using registered
> lcd panel name, and then initialize lcd panel driver.
<snip>
The header 'mipi_dsim.h' below has a lot of generic content which could
be used by other DSI controllers too. But there are things which seem
specific to the Samsung SoC.
'mipi_dsim.h' makes it sound like a header for a generic DSI controller.
Since that's not the case, you might want to consider renaming this as
's5p_mipi_dsim.h'.
Sorry for not commenting on an earlier revision.
Regards,
Archit
> +#endif /* _REGS_DSIM_H */
> diff --git a/include/linux/mipi_dsim.h b/include/linux/mipi_dsim.h
> new file mode 100644
> index 0000000..f54da24
> --- /dev/null
> +++ b/include/linux/mipi_dsim.h
> @@ -0,0 +1,359 @@
> +/* include/linux/mipi_dsim.h
> + *
> + * Platform data header for Samsung SoC MIPI-DSIM.
> + *
> + * Copyright (c) 2011 Samsung Electronics Co., Ltd
> + *
> + * InKi Dae<inki.dae@xxxxxxxxxxx>
> + * Donghwa Lee<dh09.lee@xxxxxxxxxxx>
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> +*/
> +
> +#ifndef _LINUX_MIPI_DSIM_H
> +#define _LINUX_MIPI_DSIM_H
> +
> +#include<linux/device.h>
> +#include<linux/fb.h>
> +
> +#define PANEL_NAME_SIZE (32)
> +
> +/*
> + * Enumerate display interface type.
> + *
> + * DSIM_COMMAND means cpu interface and rgb interface for DSIM_VIDEO.
> + *
> + * P.S. MIPI DSI Master has two display controller intefaces, RGB Interface
> + * for main display and CPU Interface(same as I80 Interface) for main
> + * and sub display.
> + */
> +enum mipi_dsim_interface_type {
> + DSIM_COMMAND,
> + DSIM_VIDEO
> +};
> +
> +enum mipi_dsim_virtual_ch_no {
> + DSIM_VIRTUAL_CH_0,
> + DSIM_VIRTUAL_CH_1,
> + DSIM_VIRTUAL_CH_2,
> + DSIM_VIRTUAL_CH_3
> +};
> +
> +enum mipi_dsim_burst_mode_type {
> + DSIM_NON_BURST_SYNC_EVENT,
> + DSIM_BURST_SYNC_EVENT,
> + DSIM_NON_BURST_SYNC_PULSE,
> + DSIM_BURST,
> + DSIM_NON_VIDEO_MODE
> +};
> +
> +enum mipi_dsim_no_of_data_lane {
> + DSIM_DATA_LANE_1,
> + DSIM_DATA_LANE_2,
> + DSIM_DATA_LANE_3,
> + DSIM_DATA_LANE_4
> +};
> +
> +enum mipi_dsim_byte_clk_src {
> + DSIM_PLL_OUT_DIV8,
> + DSIM_EXT_CLK_DIV8,
> + DSIM_EXT_CLK_BYPASS
> +};
> +
> +enum mipi_dsim_pixel_format {
> + DSIM_CMD_3BPP,
> + DSIM_CMD_8BPP,
> + DSIM_CMD_12BPP,
> + DSIM_CMD_16BPP,
> + DSIM_VID_16BPP_565,
> + DSIM_VID_18BPP_666PACKED,
> + DSIM_18BPP_666LOOSELYPACKED,
> + DSIM_24BPP_888
> +};
> +
> +/*
> + * struct mipi_dsim_config - interface for configuring mipi-dsi controller.
> + *
> + * @auto_flush: enable or disable Auto flush of MD FIFO using VSYNC pulse.
> + * @eot_disable: enable or disable EoT packet in HS mode.
> + * @auto_vertical_cnt: specifies auto vertical count mode.
> + * in Video mode, the vertical line transition uses line counter
> + * configured by VSA, VBP, and Vertical resolution.
> + * If this bit is set to '1', the line counter does not use VSA and VBP
> + * registers.(in command mode, this variable is ignored)
> + * @hse: set horizontal sync event mode.
> + * In VSYNC pulse and Vporch area, MIPI DSI master transfers only HSYNC
> + * start packet to MIPI DSI slave at MIPI DSI spec1.1r02.
> + * this bit transfers HSYNC end packet in VSYNC pulse and Vporch area
> + * (in mommand mode, this variable is ignored)
> + * @hfp: specifies HFP disable mode.
> + * if this variable is set, DSI master ignores HFP area in VIDEO mode.
> + * (in command mode, this variable is ignored)
> + * @hbp: specifies HBP disable mode.
> + * if this variable is set, DSI master ignores HBP area in VIDEO mode.
> + * (in command mode, this variable is ignored)
> + * @hsa: specifies HSA disable mode.
> + * if this variable is set, DSI master ignores HSA area in VIDEO mode.
> + * (in command mode, this variable is ignored)
> + * @cma_allow: specifies the number of horizontal lines, where command packet
> + * transmission is allowed after Stable VFP period.
> + * @e_interface: specifies interface to be used.(CPU or RGB interface)
> + * @e_virtual_ch: specifies virtual channel number that main or
> + * sub diaplsy uses.
> + * @e_pixel_format: specifies pixel stream format for main or sub display.
> + * @e_burst_mode: selects Burst mode in Video mode.
> + * in Non-burst mode, RGB data area is filled with RGB data and NULL
> + * packets, according to input bandwidth of RGB interface.
> + * In Burst mode, RGB data area is filled with RGB data only.
> + * @e_no_data_lane: specifies data lane count to be used by Master.
> + * @e_byte_clk: select byte clock source. (it must be DSIM_PLL_OUT_DIV8)
> + * DSIM_EXT_CLK_DIV8 and DSIM_EXT_CLK_BYPASSS are not supported.
> + * @pll_stable_time: specifies the PLL Timer for stability of the ganerated
> + * clock(System clock cycle base)
> + * if the timer value goes to 0x00000000, the clock stable bit of status
> + * and interrupt register is set.
> + * @esc_clk: specifies escape clock frequency for getting the escape clock
> + * prescaler value.
> + * @stop_holding_cnt: specifies the interval value between transmitting
> + * read packet(or write "set_tear_on" command) and BTA request.
> + * after transmitting read packet or write "set_tear_on" command,
> + * BTA requests to D-PHY automatically. this counter value specifies
> + * the interval between them.
> + * @bta_timeout: specifies the timer for BTA.
> + * this register specifies time out from BTA request to change
> + * the direction with respect to Tx escape clock.
> + * @rx_timeout: specifies the timer for LP Rx mode timeout.
> + * this register specifies time out on how long RxValid deasserts,
> + * after RxLpdt asserts with respect to Tx escape clock.
> + * - RxValid specifies Rx data valid indicator.
> + * - RxLpdt specifies an indicator that D-PHY is under RxLpdt mode.
> + * - RxValid and RxLpdt specifies signal from D-PHY.
> + */
> +struct mipi_dsim_config {
> + unsigned char auto_flush;
> + unsigned char eot_disable;
> +
> + unsigned char auto_vertical_cnt;
> + unsigned char hse;
> + unsigned char hfp;
> + unsigned char hbp;
> + unsigned char hsa;
> + unsigned char cmd_allow;
> +
> + enum mipi_dsim_interface_type e_interface;
> + enum mipi_dsim_virtual_ch_no e_virtual_ch;
> + enum mipi_dsim_pixel_format e_pixel_format;
> + enum mipi_dsim_burst_mode_type e_burst_mode;
> + enum mipi_dsim_no_of_data_lane e_no_data_lane;
> + enum mipi_dsim_byte_clk_src e_byte_clk;
> +
> + /*
> + * ===========================================
> + * | P | M | S | MHz |
> + * -------------------------------------------
> + * | 3 | 100 | 3 | 100 |
> + * | 3 | 100 | 2 | 200 |
> + * | 3 | 63 | 1 | 252 |
> + * | 4 | 100 | 1 | 300 |
> + * | 4 | 110 | 1 | 330 |
> + * | 12 | 350 | 1 | 350 |
> + * | 3 | 100 | 1 | 400 |
> + * | 4 | 150 | 1 | 450 |
> + * | 6 | 118 | 1 | 472 |
> + * | 3 | 120 | 1 | 480 |
> + * | 12 | 250 | 0 | 500 |
> + * | 4 | 100 | 0 | 600 |
> + * | 3 | 81 | 0 | 648 |
> + * | 3 | 88 | 0 | 704 |
> + * | 3 | 90 | 0 | 720 |
> + * | 3 | 100 | 0 | 800 |
> + * | 12 | 425 | 0 | 850 |
> + * | 4 | 150 | 0 | 900 |
> + * | 12 | 475 | 0 | 950 |
> + * | 6 | 250 | 0 | 1000 |
> + * -------------------------------------------
> + */
> +
> + /*
> + * pms could be calculated as the following.
> + * M * 24 / P * 2 ^ S = MHz
> + */
> + unsigned char p;
> + unsigned short m;
> + unsigned char s;
> +
> + unsigned int pll_stable_time;
> + unsigned long esc_clk;
> +
> + unsigned short stop_holding_cnt;
> + unsigned char bta_timeout;
> + unsigned short rx_timeout;
> +};
> +
> +/*
> + * struct mipi_dsim_device - global interface for mipi-dsi driver.
> + *
> + * @dev: driver model representation of the device.
> + * @id: unique device id.
> + * @clock: pointer to MIPI-DSI clock of clock framework.
> + * @irq: interrupt number to MIPI-DSI controller.
> + * @reg_base: base address to memory mapped SRF of MIPI-DSI controller.
> + * (virtual address)
> + * @lock: the mutex protecting this data structure.
> + * @dsim_info: infomation for configuring mipi-dsi controller.
> + * @master_ops: callbacks to mipi-dsi operations.
> + * @dsim_lcd_dev: pointer to activated ddi device.
> + * (it would be registered by mipi-dsi driver.)
> + * @dsim_lcd_drv: pointer to activated_ddi driver.
> + * (it would be registered by mipi-dsi driver.)
> + * @lcd_info: pointer to mipi_lcd_info structure.
> + * @state: specifies status of MIPI-DSI controller.
> + * the status could be RESET, INIT, STOP, HSCLKEN and ULPS.
> + * @data_lane: specifiec enabled data lane number.
> + * this variable would be set by driver according to e_no_data_lane
> + * automatically.
> + * @e_clk_src: select byte clock source.
> + * @pd: pointer to MIPI-DSI driver platform data.
> + */
> +struct mipi_dsim_device {
> + struct device *dev;
> + int id;
> + struct resource *res;
> + struct clk *clock;
> + unsigned int irq;
> + void __iomem *reg_base;
> + struct mutex lock;
> +
> + struct mipi_dsim_config *dsim_config;
> + struct mipi_dsim_master_ops *master_ops;
> + struct mipi_dsim_lcd_device *dsim_lcd_dev;
> + struct mipi_dsim_lcd_driver *dsim_lcd_drv;
> +
> + unsigned int state;
> + unsigned int data_lane;
> + unsigned int e_clk_src;
> + bool suspended;
> +
> + struct mipi_dsim_platform_data *pd;
> +};
> +
> +/*
> + * struct mipi_dsim_platform_data - interface to platform data
> + * for mipi-dsi driver.
> + *
> + * @lcd_panel_name: specifies lcd panel name registered to mipi-dsi driver.
> + * lcd panel driver searched would be actived.
> + * @dsim_config: pointer of structure for configuring mipi-dsi controller.
> + * @enabled: indicate whether mipi controller got enabled or not.
> + * @lcd_panel_info: pointer for lcd panel specific structure.
> + * this structure specifies width, height, timing and polarity and so on.
> + * @phy_enable: pointer to a callback controlling D-PHY enable/reset
> + */
> +struct mipi_dsim_platform_data {
> + char lcd_panel_name[PANEL_NAME_SIZE];
> +
> + struct mipi_dsim_config *dsim_config;
> + unsigned int enabled;
> + void *lcd_panel_info;
> +
> + int (*phy_enable)(struct platform_device *pdev, bool on);
> +};
> +
> +/*
> + * struct mipi_dsim_master_ops - callbacks to mipi-dsi operations.
> + *
> + * @cmd_write: transfer command to lcd panel at LP mode.
> + * @cmd_read: read command from rx register.
> + * @get_dsim_frame_done: get the status that all screen data have been
> + * transferred to mipi-dsi.
> + * @clear_dsim_frame_done: clear frame done status.
> + * @get_fb_frame_done: get frame done status of display controller.
> + * @trigger: trigger display controller.
> + * - this one would be used only in case of CPU mode.
> + * @set_early_blank_mode: set framebuffer blank mode.
> + * - this callback should be called prior to fb_blank() by a client driver
> + * only if needing.
> + * @set_blank_mode: set framebuffer blank mode.
> + * - this callback should be called after fb_blank() by a client driver
> + * only if needing.
> + */
> +
> +struct mipi_dsim_master_ops {
> + int (*cmd_write)(struct mipi_dsim_device *dsim, unsigned int data_id,
> + const unsigned char *data0, unsigned int data1);
> + int (*cmd_read)(struct mipi_dsim_device *dsim, unsigned int data_id,
> + unsigned int data0, unsigned int req_size, u8 *rx_buf);
> + int (*get_dsim_frame_done)(struct mipi_dsim_device *dsim);
> + int (*clear_dsim_frame_done)(struct mipi_dsim_device *dsim);
> +
> + int (*get_fb_frame_done)(struct fb_info *info);
> + void (*trigger)(struct fb_info *info);
> + int (*set_early_blank_mode)(struct mipi_dsim_device *dsim, int power);
> + int (*set_blank_mode)(struct mipi_dsim_device *dsim, int power);
> +};
> +
> +/*
> + * device structure for mipi-dsi based lcd panel.
> + *
> + * @name: name of the device to use with this device, or an
> + * alias for that name.
> + * @dev: driver model representation of the device.
> + * @id: id of device to be registered.
> + * @bus_id: bus id for identifing connected bus
> + * and this bus id should be same as id of mipi_dsim_device.
> + * @irq: irq number for signaling when framebuffer transfer of
> + * lcd panel module is completed.
> + * this irq would be used only for MIPI-DSI based CPU mode lcd panel.
> + * @master: pointer to mipi-dsi master device object.
> + * @platform_data: lcd panel specific platform data.
> + */
> +struct mipi_dsim_lcd_device {
> + char *name;
> + struct device dev;
> + int id;
> + int bus_id;
> + int irq;
> +
> + struct mipi_dsim_device *master;
> + void *platform_data;
> +};
> +
> +/*
> + * driver structure for mipi-dsi based lcd panel.
> + *
> + * this structure should be registered by lcd panel driver.
> + * mipi-dsi driver seeks lcd panel registered through name field
> + * and calls these callback functions in appropriate time.
> + *
> + * @name: name of the driver to use with this device, or an
> + * alias for that name.
> + * @id: id of driver to be registered.
> + * this id would be used for finding device object registered.
> + */
> +struct mipi_dsim_lcd_driver {
> + char *name;
> + int id;
> +
> + void (*power_on)(struct mipi_dsim_lcd_device *dsim_dev, int enable);
> + void (*set_sequence)(struct mipi_dsim_lcd_device *dsim_dev);
> + int (*probe)(struct mipi_dsim_lcd_device *dsim_dev);
> + int (*remove)(struct mipi_dsim_lcd_device *dsim_dev);
> + void (*shutdown)(struct mipi_dsim_lcd_device *dsim_dev);
> + int (*suspend)(struct mipi_dsim_lcd_device *dsim_dev);
> + int (*resume)(struct mipi_dsim_lcd_device *dsim_dev);
> +};
> +
> +/*
> + * register mipi_dsim_lcd_device to mipi-dsi master.
> + */
> +int s5p_mipi_dsi_register_lcd_device(struct mipi_dsim_lcd_device
> + *lcd_dev);
> +/**
> + * register mipi_dsim_lcd_driver object defined by lcd panel driver
> + * to mipi-dsi driver.
> + */
> +int s5p_mipi_dsi_register_lcd_driver(struct mipi_dsim_lcd_driver
> + *lcd_drv);
> +#endif /* _LINUX_MIPI_DSIM_H */
--
To unsubscribe from this list: send the line "unsubscribe linux-fbdev" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
