https://bugzilla.kernel.org/show_bug.cgi?id=195893 Bug ID: 195893 Summary: Blocksize changing +1 / bad geometry / Product: File System Version: 2.5 Kernel Version: 4.9.0-2-amd64 #1 SMP Debian 4.9.18-1 (2017-03-30) x86_64 GNU/Linux Hardware: x86-64 OS: Linux Tree: Mainline Status: NEW Severity: normal Priority: P1 Component: ext4 Assignee: fs_ext4@xxxxxxxxxxxxxxxxxxxx Reporter: 189840BSGMKUQECR@xxxxxxxxxxxxx Regression: No I am handling a lot of disks. Lately, I have a lot of disks that linux refuses to mount, because the ext4 filesystem is exceeding the physical disk size. Setup: The disks have been installd while installed natively(sata) in laptops and are formatted with ext4. The disks have been removed from the original laptops and are connected via USB3-Docking Station to a Lenovo W520 running Debian. Some of them are encrypted with LUKS and some are unencrypted. Both are affected. Using fsck.ext4, I get a message like: The filesystem size (according to the superblock) is 113445126 blocks The physical size of the device is 113445125 blocks Either the superblock or the partition table is likely to be corrupt! First I thought it may have been a problem when using dd to write to a smaller disk. But now it happened to a disk I used 5 Minutes ago without any issues. I accidentally disconnected the cable. And got the fault. Disks of different vendors and size are affected. I use different USB3-Docking Stations. I am not sure but I think there were at least one disk affected having no partition table (just ext4 on the raw disk). I cannot yet reproduce the fault. But I have already had more than 15 disks with this issue over the past 6 months. Symptoms: The disk does not mount The partition exceeds the physical size by exactly 1 block. Additional information: hdparm /dev/sdd /dev/sdd: HDIO_DRIVE_CMD(identify) failed: Invalid argument readonly = 0 (off) readahead = 256 (on) geometry = 60801/255/63, sectors = 976773165, start = 0 dmesg: [611569.085740] usb 2-2: new SuperSpeed USB device number 45 using xhci_hcd [611569.115972] usb 2-2: New USB device found, idVendor=1234, idProduct=5678 [611569.115984] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3 [611569.115990] usb 2-2: Product: VLI Product String [611569.115995] usb 2-2: Manufacturer: VLI manufacture String [611569.115999] usb 2-2: SerialNumber: XXXXXXREMOVEDXXXXXXX [611569.116953] usb-storage 2-2:1.0: USB Mass Storage device detected [611569.117157] scsi host7: usb-storage 2-2:1.0 [611572.830469] scsi 7:0:0:0: Direct-Access ST950042 0AS 0002 PQ: 0 ANSI: 2 [611572.831076] sd 7:0:0:0: Attached scsi generic sg2 type 0 [611572.834528] sd 7:0:0:0: [sdd] 976773165 512-byte logical blocks: (500 GB/466 GiB) [611572.835013] sd 7:0:0:0: [sdd] Write Protect is off [611572.835016] sd 7:0:0:0: [sdd] Mode Sense: 03 00 00 00 [611572.835539] sd 7:0:0:0: [sdd] No Caching mode page found [611572.835546] sd 7:0:0:0: [sdd] Assuming drive cache: write through [611572.878044] sdd: sdd1 sdd2 sdd3 [611572.878147] sdd: p3 size 907565104 extends beyond EOD, enabling native capacity [611572.894730] sdd: sdd1 sdd2 sdd3 [611572.894821] sdd: p3 size 907565104 extends beyond EOD, truncated [611573.935026] sd 7:0:0:0: [sdd] Attached SCSI disk [611628.215491] EXT4-fs (dm-0): bad geometry: block count 113445126 exceeds size of device (113445125 blocks) [611726.355560] EXT4-fs (dm-0): mounted filesystem with ordered data mode. Opts: (null) Workaround - fix: fsck.ext4 /dev/sdd3 - press "n" to ignore different physical size - most times no more errors show up resize2fs /dev/sdd3 mount /dev/sdd3 /mnt/disk3 Now the device is fixed. And can be used again. As far as I can see there is no data loss. -- You are receiving this mail because: You are watching the assignee of the bug.