Hi, dmesg is probably useles: Probably some logs after mounting...: # dmesg | grep EXT EXT3-fs (md2): mounted filesystem with ordered data mode EXT3-fs (md2): using internal journal EXT3-fs (dm-2): using internal journal EXT3-fs (dm-2): mounted filesystem with ordered data mode EXT4-fs (dm-8): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (dm-3): mounted filesystem with ordered data mode. Opts: (null) EXT4-fs (dm-12): mounted filesystem without journal. Opts: (null) EXT4-fs (dm-8): re-mounted. Opts: commit=0 EXT4-fs (dm-3): re-mounted. Opts: commit=0 EXT4-fs (dm-12): re-mounted. Opts: commit=0 EXT4-fs (dm-28): mounted filesystem with ordered data mode. Opts: (null) EXT3-fs (dm-10): using internal journal EXT3-fs (dm-10): mounted filesystem with ordered data mode On last few lines, there is some info about usb key used on thic pc: # dmesg | tail -n 30 sd 14:0:0:0: [sdg] Asking for cache data failed sd 14:0:0:0: [sdg] Assuming drive cache: write through sdg: sdg1 sd 14:0:0:0: [sdg] Asking for cache data failed sd 14:0:0:0: [sdg] Assuming drive cache: write through sd 14:0:0:0: [sdg] Attached SCSI disk mdadm: sending ioctl 1261 to a partition! mdadm: sending ioctl 1261 to a partition! usb 2-4.4: USB disconnect, device number 10 hda-intel: IRQ timing workaround is activated for card #0. Suggest a bigger bdl_pos_adj. usb 1-1: new high-speed USB device number 2 using ehci_hcd usb 1-1: New USB device found, idVendor=0951, idProduct=1687 usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 1-1: Product: DT R400 usb 1-1: Manufacturer: Kingston usb 1-1: SerialNumber: 0018F30C7FX10B000XX029 scsi15 : usb-storage 1-1:1.0 scsi 15:0:0:0: Direct-Access Kingston DT R400 PMAP PQ: 0 ANSI: 0 CCS sd 15:0:0:0: Attached scsi generic sg6 type 0 sd 15:0:0:0: [sdg] 7774208 512-byte logical blocks: (3.98 GB/3.70 GiB) sd 15:0:0:0: [sdg] Write Protect is off sd 15:0:0:0: [sdg] Mode Sense: 23 00 00 00 sd 15:0:0:0: [sdg] No Caching mode page present sd 15:0:0:0: [sdg] Assuming drive cache: write through sd 15:0:0:0: [sdg] No Caching mode page present sd 15:0:0:0: [sdg] Assuming drive cache: write through sdg: sdg1 sdg2 sd 15:0:0:0: [sdg] No Caching mode page present sd 15:0:0:0: [sdg] Assuming drive cache: write through sd 15:0:0:0: [sdg] Attached SCSI removable disk Other lines from dmesg seems not relevant. Should I post them too? PS: Writing to disk from jbd2/dm-3-8 still active (iotop shows it still on top of I/O activity). LuVar ----- "Theodore Ts'o" <tytso@xxxxxxx> wrote: > On Mon, Jul 30, 2012 at 08:26:20PM +0100, LuVar wrote: > > Hi, > > I have seriouse issue here. I have copyied about 7GB files to one of > my ext4 partitions and from that point of time there is sustained > write to that partition from jbd2/dm-3-8 process. I have lunched "sudo > sync" command (about day ago :) and a few hours a after sync start, I > have tryied to use umount on that partition... Booth of them are still > running... > > > > I have no serious data there, but if I could be helpfull in > bugreport, give me some info what to do. > > Try running the dmesg command, and see if there's anything > interesting > there. If you're not sure if it's interesting, send it to us and we > can take a quick look at it. > > Regards, > > - Ted -- To unsubscribe from this list: send the line "unsubscribe linux-ext4" in the body of a message to majordomo@xxxxxxxxxxxxxxx More majordomo info at http://vger.kernel.org/majordomo-info.html
