[Bridge] tcpdump/pcap problem

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hello
I have a problem with running tcpdump on network devices used in bridge
group:
The bridge configuration is as follows:

/usr/sbin/brctl addbr br0
/usr/sbin/brctl stp br0 no
/sbin/ifconfig eth0 up
/usr/sbin/brctl addif br0 eth0
/usr/sbin/brctl addif br0 wlan0

brctl show command output:

# brctl show
bridge name     bridge id               STP enabled     interfaces
br0             8000.0014bf6f81b2       no              eth0
                                                       wlan0

ifconfig command output:

# ifconfig
br0             Link encap:Ethernet  HWaddr 00:14:BF:6F:81:B2
                inet addr:10.1.1.201  Bcast:192.168.1.255  Mask:
255.255.255.0
                UP BROADCAST RUNNING PROMISC MULTICAST  MTU:1500  Metric:1
                RX packets:9541 errors:0 dropped:0 overruns:0 frame:0
                TX packets:2717 errors:0 dropped:0 overruns:0 carrier:0
                collisions:0 txqueuelen:100
                RX bytes:1806483 (1.7 MiB)  TX bytes:312466 (305.1 KiB)

eth0            Link encap:Ethernet  HWaddr 00:14:BF:6F:81:B2
                UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
                RX packets:10111 errors:0 dropped:0 overruns:0 frame:0
                TX packets:3139 errors:0 dropped:0 overruns:0 carrier:0
                collisions:0 txqueuelen:100
                RX bytes:1897558 (1.8 MiB)  TX bytes:354798 (346.4 KiB)

lo              Link encap:Local Loopback
                inet addr:127.0.0.1  Mask:255.0.0.0
                UP LOOPBACK RUNNING  MTU:16436  Metric:1
                RX packets:0 errors:0 dropped:0 overruns:0 frame:0
                TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
                collisions:0 txqueuelen:0
                RX bytes:0 (0.0 B)  TX bytes:0 (0.0 B)

wlan0           Link encap:Ethernet  HWaddr 00:14:BF:6F:81:B2
                UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
                RX packets:435 errors:0 dropped:0 overruns:0 frame:0
                TX packets:5853 errors:0 dropped:0 overruns:0 carrier:0
                collisions:0 txqueuelen:100
                RX bytes:42715 (41.7 KiB)  TX bytes:625334 (610.6 KiB)

The problem is that tcpdump does not show any traffic when attached to eth0
or wlan0. Traffic directed to the bridging device is visible on br0. What
should I do to make tcpdump see traffic entering eth0 and wlan0 ? Note that
this is an embedded MIPS based device with binary only network interface
kernel modules ( linksys router running linux ) .

tcpdump/pcap versions:
tcpdump version 3.9.5
libpcap version 0.9.5

WoytekM
-------------- next part --------------
An HTML attachment was scrubbed...
URL: http://lists.osdl.org/pipermail/bridge/attachments/20061127/6043ade3/attachment.htm 


[Index of Archives]     [Netdev]     [AoE Tools]     [Linux Wireless]     [Kernel Newbies]     [Security]     [Linux for Hams]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux RAID]     [Linux Admin]     [Samba]     [Video 4 Linux]

  Powered by Linux